Sr(II) and Ba(II) Alkaline Earth Metal-Organic Frameworks (AE-MOFs) for Selective Gas Adsorption, Energy Storage, and Environmental Application.

Two new alkaline earth metal-organic frameworks (AE-MOFs) containing Sr(II) (UPJS-15) or Ba(II) (UPJS-16) cations and extended tetrahedral linker (MTA) were synthesized and characterized in detail (UPJS stands for University of Pavol Jozef Safarik). Single-crystal X-ray analysis (SC-XRD) revealed that the materials are isostructural and, in their frameworks, one-dimensional channels are present with the size of ~11 × 10 Å2. The activation process of the compounds was studied by the combination of in situ heating infrared spectroscopy (IR), thermal analysis (TA) and in situ high-energy powder X-ray diffraction (HE-PXRD), which confirmed the stability of compounds after desolvation. The prepared compounds were investigated as adsorbents of different gases (Ar, N2, CO2, and H2). Nitrogen and argon adsorption measurements showed that UPJS-15 has SBET area of 1321 m2 g-1 (Ar) / 1250 m2 g-1 (N2), and UPJS-16 does not adsorb mentioned gases. From the environmental application, the materials were studied as CO2 adsorbents, and both compounds adsorb CO2 with a maximum capacity of 22.4 wt.% @ 0 °C; 14.7 wt.% @ 20 °C and 101 kPa for UPJS-15 and 11.5 wt.% @ 0°C; 8.4 wt.% @ 20 °C and 101 kPa for UPJS-16. According to IAST calculations, UPJS-16 shows high selectivity (50 for CO2/N2 10:90 mixture and 455 for CO2/N2 50:50 mixture) and can be applied as CO2 adsorbent from the atmosphere even at low pressures. The increased affinity of materials for CO2 was also studied by DFT modelling, which revealed that the primary adsorption sites are coordinatively unsaturated sites on metal ions, azo bonds, and phenyl rings within the MTA linker. Regarding energy storage, the materials were studied as hydrogen adsorbents, but the materials showed low H2 adsorption properties: 0.19 wt.% for UPJS-15 and 0.04 wt.% for UPJS-16 @ -196 °C and 101 kPa. The enhanced CO2/H2 selectivity could be used to scavenge carbon dioxide from hydrogen in WGS and DSR reactions. The second method of applying samples in the area of energy storage was the use of UPJS-15 as an additive in a lithium-sulfur battery. Cyclic performance at a cycling rate of 0.2 C showed an initial discharge capacity of 337 mAh g-1, which decreased smoothly to 235 mAh g-1 after 100 charge/discharge cycles.

Adsorption and Release Properties of Drug Delivery System Naproxen-SBA-15: Effect of Surface Polarity, Sodium/Acid Drug Form and pH.

Mesoporous silica SBA-15 was prepared via sol-gel synthesis and functionalized with different types of organosilanes containing various organic functional groups: (3-aminopropyl)triethoxysilane (SBA-15-NH2), (3-mercaptopropyl)triethoxysilane (SBA-15-SH), triethoxymethylsilane (SBA-15-CH3), triethoxyphenylsilane (SBA-15-Ph), and (3-isocynatopropyl)triethoxysilane (SBA-15-NCO). The prepared materials were investigated as drug delivery systems for naproxen. As model drugs, naproxen acid (HNAP) and its sodium salt (NaNAP) were used. Mentioned medicaments belong to the group of non-steroidal anti-inflammatory drugs (NSAIDs). The prepared materials were characterized by different analytical methods such as transmission electron microscopy (TEM), infrared spectroscopy (IR), nitrogen adsorption/desorption analysis (N2), thermogravimetric analysis (TG), 1H, 13C and 23Na solid-state nuclear magnetic resonance spectroscopy (1H, 13C and 23Na ss-NMR). The abovementioned analytical techniques confirmed the successful grafting of functional groups to the SBA-15 surface and the adsorption of drugs after the impregnation process. The BET area values decreased from 927 m2 g-1 for SBA-15 to 408 m2 g-1 for SBA-15-NCO. After drug encapsulation, a more significant decrease in surface area was observed due to the filling of pores with drug molecules, while the most significant decrease was observed for the SBA-15-NH2 material (115 m2 g-1 for NaNAP and 101 m2 g-1 for HNAP). By combining TG and nitrogen adsorption results, the occurrence of functional groups and the affinity of drugs to the carriers' surface were calculated. The dominant factor was the volume of functional groups and intermolecular interactions. The highest drug affinity values were observed for phenyl and amine-modified materials (SBA-15-Ph = 1.379 µmol m-2 mmol-1 for NaNAP, 1.761 µmol m-2 mmol-1 for HNAP and SBA-15-NH2 = 1.343 µmol m-2 mmol-1 for NaNAP, 1.302 µmol m-2 mmol-1 for HNAP) due to the formation of hydrogen bonds and π-π interactions, respectively. Drug release properties and kinetic studies were performed at t = 37 °C (normal human body temperature) in different media with pH = 2 as simulated human gastric fluid and pH = 7.4, which simulated a physiological environment. Determination of drug release quantity was performed with UV-VIS spectroscopy. The surface polarity, pH and naproxen form influenced the total released amount of drug. In general, naproxen sodium salt has a higher solubility than its acid form, thus significantly affecting drug release from surface-modified SBA-15 materials. Different pH conditions involved surface protonation and formation/disruption of intermolecular interactions, influencing both the release rate and the total released amount of naproxen. Different kinetic models, zero-order, first-order, Higuchi and Hixson-Crowell models, were used to fit the drug release data. According to the obtained experimental results, the drug release rates and mechanisms were determined.

Energy-Efficient Iodine Uptake by a Molecular Host⋠Guest Crystal.

Recently, porous organic crystals (POC) based on macrocycles have shown exceptional sorption and separation properties. Yet, the impact of guest presence inside a macrocycle prior to adsorption has not been studied. Here we show that the inclusion of trimethoxybenzyl-azaphosphatrane in the macrocycle cucurbit[8]uril (CB[8]) affords molecular porous host⋅guest crystals (PHGC-1) with radically new properties. Unactivated hydrated PHGC-1 adsorbed iodine spontaneously and selectively at room temperature and atmospheric pressure. The absence of (i) heat for material synthesis, (ii) moisture sensitivity, and (iii) energy-intensive steps for pore activation are attractive attributes for decreasing the energy costs. 1 H NMR and DOSY were instrumental for monitoring the H2 O/I2 exchange. PHGC-1 crystals are non-centrosymmetric and I2 -doped crystals showed markedly different second harmonic generation (SHG), which suggests that iodine doping could be used to modulate the non-linear optical properties of porous organic crystals.

Thermosensitive Drug Delivery System SBA-15-PEI for Controlled Release of Nonsteroidal Anti-Inflammatory Drug Diclofenac Sodium Salt: A Comparative Study.

Mesoporous SBA-15 silica material was prepared by the sol-gel method and functionalized with thermosensitive polyethylenimine polymers with different molecular weight (g·mol-1): 800 (SBA-15(C)-800), 1300 (SBA-15(C)-1300) and 2000 (SBA-15(C)-2000). The nonsteroidal anti-inflammatory drug (NSAID) diclofenac sodium was selected as a model drug and encapsulated into the pores of prepared supports. Materials were characterized by the combination of infrared spectroscopy (IR), atomic force microscopy (AFM), transmission electron microscopy (TEM), photon cross-correlation spectroscopy (PCCS), nitrogen adsorption/desorption analysis, thermogravimetry (TG), differential scanning calorimetry (DSC) and small-angle X-ray diffraction (SA-XRD) experiments. The drug release from prepared matrixes was realized in two model media differing in pH, namely small intestine environment/simulated body fluid (pH = 7.4) and simulated gastric fluid (pH = 2), and at different temperatures, namely normal body temperature (T = 37 °C) and inflammatory temperature (T = 42 °C). The process of drug loading into the pores of prepared materials from the diclofenac sodium salt solutions with different concentrations and subsequent quantitative determination of released drugs was analyzed by UV-VIS spectroscopy. Analysis of prepared SBA-15 materials modified with polyethylenimines in solution showed a high ability to store large amounts of the drug, up to 230 wt.%. Experimental results showed their high drug release into the solution at pH = 7.4 for both temperatures, which is related to the high solubility of diclofenac sodium in a slightly alkaline environment. At pH = 2, a difference in drug release rate was observed between both temperatures. Indeed, at a higher temperature, the release rates and the amount of released drug were 2-3 times higher than those observed at a lower temperature. Different kinetic models were used to fit the obtained drug release data to determine the drug release rate and its release mechanism. Moreover, the drug release properties of prepared compounds were compared to a commercially available medicament under the same experimental conditions.

Cytotoxicity study and influence of SBA-15 surface polarity and pH on adsorption and release properties of anticancer agent pemetrexed.

Mesoporous material SBA-15 was functionalized with different polar and nonpolar groups: 3-aminopropyl, (SBA-15-NH2), 3-isocyanatopropyl (SBA-15-NCO), 3-mercaptopropyl (SBA-15-SH), methyl (SBA-15-CH3) and phenyl (SBA-15-Ph). The resulting surface grafted materials were investigated as matrices for controlled drug delivery. Anticancer agent, pemetrexed (disodium pemetrexed heptahydrate) was selected as a model drug and loaded in the unmodified and functionalized SBA-15 materials. Materials were characterized by elemental analysis, infrared spectroscopy, transmission electron microscopy, nitrogen adsorption/desorption analysis, small angle X-ray scattering, powder X-ray diffraction, solid state NMR spectroscopy and thermogravimetry. It was shown that surface modification has an impact on both encapsulated drug amount and release properties. Release experiments were performed into two media with different pH: simulated body fluid (pH = 7.4) and simulated gastric fluid (pH = 2). In general, the effect of pH was reflected by the lower release of pemetrexed under acidic conditions (pH = 2) compared to slightly alkaline saline environment (pH = 7.4). The release rate of pemetrexed from propylamine-, propylisocyanate- and phenyl-modified SBA-15 was found to be effectively controlled by intermolecular interactions as compared to that from pure SBA-15, SBA-15-SH, and SBA-15-CH3, that evidenced a steady and similar release. The highest release was observed for methyl-functionalized material whose hydrophobic surface accelerates the pemetrexed release. The data obtained from release studies were fitted using various kinetic models to determine the pemetrexed release mechanism and its release rate. The best correlations were found for Korsmeyer-Peppas and Higuchi models. Moreover, the theoretical three-parameter model for drug release kinetic was applied to calculate the strength of drug-support interactions. The in vitro cell study was performed on SKBR3 cancer cells and obtained results demonstrated that the modification of the mesoporous silica material by grafted polar/nonpolar groups may significantly affect the compatibility of this material with cells, drug release from this material and subsequent biological activity of PEM.

Doxorobicin as cargo in a redox-responsive drug delivery system capped with water dispersible ZnS nanoparticles.

In this work, we have prepared and investigated a redox-responsive drug delivery system (DDS) based on a porous carrier. Doxorubicin (DOX), a chemotherapy medication for treatment of different kinds of cancer, was used as a model drug in the study. DOX was loaded in ordered hexagonal mesoporous silica SBA-15, a nanoporous material with good biocompatibility, stability, large pore size and specific surface area (S BET = 908 m2 g-1, V P = 0.79 cm3 g-1, d = 5.9 nm) and easy surface modification. To prepare the redox-responsive system, cystamine derivative ligands, with redox active disulphide linkers were grafted onto the surface of SBA-15. To ensure no significant premature release of DOX from the porous system, thioglycolic acid modified ZnS nanoparticles (ZnS-COOH NPs) were used as pore capping agents. The grafted redox-responsive cystamine derivative ligand containing disulphide linkers was bonded by a peptide bond to the thioglycolic acid groups of ZnS-COOH NPs, capping the pores. Once the disulphide bond was cleaved, the ZnS-COOH NPs caps were released and pores were opened to deliver the DOX cargo. The dithiol bond was cleavable by redox active molecules such as dithiothreitol (DTT) or glutathione, the concentration of which in cancer cells is 4 times higher than in healthy cells. The redox release of DOX was studied in two different media, physiological saline solution with DTT and saline without DTT. The prepared DDS proved the concept of redox responsive release. All samples were characterised by powder X-ray diffraction (XRD), transition electron microscopy (TEM), nitrogen adsorption/desorption at 77 K, Fourier-transform infrared spectroscopy (FTIR), thermal analysis and zeta potential measurements. The presence of semiconducting ZnS nanoparticle caps on the pore openings was detected by magnetic measurements using SQUID magnetometry showing that such cargo systems could be monitored using magnetic measurements which opens up the possibilities of using such drug delivery systems as theranostic agents.

A single-crystal-to-single-crystal transformation affording photochromic 3D MORF crystals.

Metal-organic framework (MOF) type crystals in which rigid, viologen-based pillars are surrounded by cucurbit[7]uril (CB[7]) macrocycles are described. These metal-organic rotaxane frameworks (MORF) are obtained by desolvation of a crystal precursor featuring a network already near-optimal toward 3D metal-ligand reticulation and show reversible photochromism.

A drug delivery system based on switchable photo-controlled p-coumaric acid derivatives anchored on mesoporous silica.

A stimuli-responsive drug delivery system consisting of mesoporous silica with its surface modified by p-coumaric acid derivatives (CA) as photo-switchable ligands was studied for the delivery of the non-steroidal anti-inflammatory drug (NSAID) naproxen. For this purpose, MCM-41 mesoporous silica material was prepared and post-synthetically modified by the grafting of a triethoxysilyl derivative of p-coumaric acid, which undergoes a reversible photo-dimerization under UV irradiation and creates the "valves" on the surface of silica allowing targeted opening/closing of the pores. Naproxen was encapsulated into grafted MCM-41 and drug release studies were performed in two different media, in a simulated gastric fluid (pH = 2) and in a simulated body fluid (pH = 7.4). Differences in drug release were observed after irradiation of the material using UV light at λ = 365 nm (closed pore configuration) and UV light at λ = 254 nm (opened pore configuration).

Self-assembled liquid crystalline nanoparticles as an ophthalmic drug delivery system. Part I: influence of process parameters on their preparation studied by experimental design.

To develop self-assembled liquid crystalline nanoparticles as a drug delivery system for keratoconus treatment, a formulation containing riboflavin a water-soluble drug, two surfactants (poloxamer 407 and mono acyl glycerol - monoolein-) and water was optimized and prepared by emulsification and a homogenization process. A fractional factorial design was applied to estimate the main effects and interaction effects of five parameters on two responses, namely particle size and encapsulation efficiency. The five parameters are the temperature of the two phases, the duration of emulsification, the presence of heating during homogenization, the number of passes and pressure. The most influent parameters are the presence of heating during the homogenization and the pressure that led to the production of nanoparticles with an average size of 145 nm and an average encapsulation efficiency of 46%.

Self-assembled liquid crystalline nanoparticles as an ophthalmic drug delivery system. Part II: optimization of formulation variables using experimental design.

In the field of keratoconus treatment, a lipid-based liquid crystal nanoparticles system has been developed to improve the preocular retention and ocular bioavailability of riboflavin, a water-soluble drug. The formulation of this ophthalmic drug delivery system was optimized by a simplex lattice experimental design. The delivery system is composed of three main components that are mono acyl glycerol (monoolein), poloxamer 407 and water and two secondary components that are riboflavin and glycerol (added to adjust the osmotic pressure). The amounts of these three main components were selected as the factors to systematically optimize the dependent variables that are the encapsulation efficiency and the particle size. In this way, 12 formulas describing experimental domain of interest were prepared. Results obtained using small angle X-rays scattering (SAXS) and cryo-transmission electron microscopy (cryo-TEM) evidenced the presence of nano-objects with either sponge or hexagonal inverted structure. In the zone of interest, the percentage of each component was determined to obtain both high encapsulation efficiency and small size of particles. Two optimized formulations were found: F7 and F1. They are very close in the ternary phase diagram as they contain 6.83% of poloxamer 407; 44.18% and 42.03% of monoolein; 46.29% and 48.44% of water for F7 and F11, respectively. These formulations displayed a good compromise between inputs and outputs investigated.

Organic multishell isostructural host-guest crystals: fullerenes C(60) inside a nitroxide open framework.

The dinitroxide biradical crystallizes forming hexagonal open frameworks with one-dimensional corrugated channels filled with crystallization solvent. The large pockets constitutive of the channels allowed the inclusion of C(60) in the paramagnetic network. The rapidity and high fidelity of crystal growth were used to prepare isostructural multilayer host-guest crystals successively stained with C(60).

Electrochemical fabrication and properties of highly ordered Fe-doped TiO2 nanotubes.

Highly-ordered Fe-doped TiO(2) nanotubes (TiO(2)nts) were fabricated by anodization of co-sputtered Ti-Fe thin films in a glycerol electrolyte containing NH(4)F. The as-sputtered Ti-Fe thin films correspond to a solid solution of Ti and Fe according to X-ray diffraction. The Fe-doped TiO(2)nts were studied in terms of composition, morphology and structure. The characterization included scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, UV/Vis spectroscopy, X-ray photoelectron spectroscopy and Mott-Schottky analysis. As a result of the Fe doping, an indirect bandgap of 3.0 eV was estimated using Tauc's plot, and this substantial red-shift extends its photoresponse to visible light. From the Mott-Schottky analysis, the flat-band potential (E(fb)) and the charge carrier concentration (N(D)) were determined to be -0.95 V vs Ag/AgCl and 5.0×10(19) cm(-3) respectively for the Fe-doped TiO(2)nts, whilst for the undoped TiO(2)nts, E(fb) of -0.85 V vs Ag/AgCl and N(D) of 6.5×10(19) cm(-3) were obtained.

Computational investigation of the adsorption of carbon dioxide onto zirconium oxide clusters.

A theoretical investigation of the adsorption of CO2 onto ZrO2 is presented. Various cluster models were used to mimic different basic and acidic sites on the surface. The method used was the density functional theory with the generalized gradient approximation and including Grimme's empirical model in order to properly describe the weak interactions that may occur between the adsorbate and the surface. We found that the adsorption at sites exhibiting two adjacent unsaturated zirconium atoms led to either the exothermic dissociation of CO2 or to a strongly physisorbed state. By contrast, on a single unsaturated zirconium, CO2 was adsorbed in an apical manner. In this case, the molecule is highly polarized and the adsorption energy amounts to -64.6 kJ mol⁻¹. Finally, the weakest adsorption of CO2 occurred on the basic OH sites on the surface.

Microcalorimetric investigation of high-surface-area mesoporous titania samples for CO2 adsorption.

Mesoporous titania powders were synthesized using the triblock copolymer F127 (PEO(106)PPO(70)PEO(106)) as a surfactant template. Two different procedures (ammonia and/or low-temperature treatment at 393 K) were successfully applied to stabilize the mesoporous structure, resulting in significantly increased surface areas and pore volumes with respect to those of the untreated titania powders. Three of these samples were chosen for further investigation by adsorption microcalorimetry. These samples are characterized by high surface areas (varying between 340 and 141 m (2) g (-1)) and a varying degree of crystallization (anatase phase). The samples were compared to nanosized anatase particles treated to 873 K. The adsorption microcalorimetry was carried out using nitrogen and carbon dioxide at 77 and 303 K, respectively, to gain complementary information about the surfaces. Nitrogen at 77 K showed, for the three samples, adsorption enthalpies at low coverage of similar values, approximately -19 to -22 kJ mol (-1), indicating that the probe gas interacts with similar energetic surface sites. Two distinct energetic regions are observed, the first of which increases with increasing pretreatment temperature, which can be related to increased sample crystallinity. The adsorption of carbon dioxide at 303 K showed high adsorption enthalpies (up to approximately 65-80 kJ mol (-1)), highlighting strong interactions of the carbon dioxide with the titania surface at low pressures. Finally, the CO(2) adsorption properties of the titania samples (adsorbed amount and enthalpies of adsorption) are compared with those of other nanosized adsorbents. This comparison shows the potentiality of mesoporous titania powders for the adsorption of CO(2).