The utility of ultraviolet beam in advanced oxidation-reduction processes: a review on the mechanism of processes and possible production free radicals.

Advanced oxidation processes (AOPs) and advanced reduction processes (ARPs) are a set of chemical treatment procedures designed to eliminate organic (sometimes inorganic) contamination in water and wastewater by producing free reactive radicals (FRR). UV irradiation is one of the factors that are effectively used in oxidation-reduction processes. Not only does the UV beam cause the photolysis of contamination, but it also leads to the product of FRR by affecting oxidants-reductant, and the pollutant decomposition occurs by FRR. UV rays produce active radical species indirectly in an advanced redox process by affecting an oxidant (O3, H2O2), persulfate (PS), or reducer (dithionite, sulfite, sulfide, iodide, ferrous). Produced FRR with high redox potential (including oxidized or reduced radicals) causes detoxification and degradation of target contaminants by attacking them. In this review, it was found that ultraviolet radiation is one of the important and practical parameters in redox processes, which can be used to control a wide range of impurities.

Adsorption-photocatalytic processes for removal of pentachlorophenol contaminant using FeNi3/SiO2/ZnO magnetic nanocomposite under simulated solar light irradiation.

The adsorption followed by photocatalytic degradation process was examined for the pentachlorophenol (PCP) removal from aqueous solution. These processes were accomplished by using FeNi3/SiO2/ZnO magnetic nanocomposite as an adsorbent-photocatalytic agent and under the irradiation of solar light. The magnetic nanocomposite used was first synthesized and then was characterized using transmission electron microscopy (TEM), field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDX), vibrating-sample magnetometer (VSM), and X-ray diffraction (XRD) spectroscopy. The PCP removal efficiency was tested for various factors, including pH, PCP concentration, and nanocomposite dose at different contact times. The characterization results of TEM, FE-SEM, and VSM analysis showed that the synthesized nanoparticles are amorphous and tend to agglomerate due to their high super-paramagnetic property. In addition, the EDX technique showed that the Zn and O elements had the highest weight percent in the synthesized nanocomposite, respectively. On the other hand, XRD analysis revealed that the crystalline size of the nanoparticles was about 42 nm. The kinetic of PCP degradation followed the pseudo-first-order model with R2 = 0.978. According to the results of the isotherm study, the adsorption of PCP onto the nanoparticles followed the Freundlich model. The results of adsorption-photocatalytic degradation experiments showed that 100% removal of PCP was obtained at optimum conditions of pH = 3, nanocomposite dose = 0.5 g/L, contact time = 180 min, and initial PCP concentration of 10 mg/L. Through the results obtained from this study, the adsorption process followed by solar light photocatalytic degradation process using FeNi3/SiO2/ZnO magnetic nanocomposite is found to be an efficacious treatment method for the removal of PCP contaminant from water and wastewater.

A comprehensive study on the application of FeNi3@SiO2@ZnO magnetic nanocomposites as a novel photo-catalyst for degradation of tamoxifen in the presence of simulated sunlight.

Pharmaceutical compounds at trace concentrations are found in the environment, especially in drinking water and food, posing significant negative effects on humans as well as on animals. This paper aimed to examine the diagnostic catalytic properties and efficacy of a novel synthesized photocatalyst, namely FeNi3@SiO2@ZnO magnetic nanocomposite, for the removal of tamoxifen (TMX) from wastewater under simulated sunlight. According to the results, it was found that TMX was completely degraded operating under optimized conditions (i.e. pH = 7, catalyst dose = 0.01 g/L, initial TMX concentration = 20 mg/L and reaction time = 60 min). The reaction kinetics of TMX degradation followed a pseudo-first order kinetics model. The final by-products from the TMX photodegradation were water, carbon dioxide, acetic acid, nitroacetic acid methyl ester, 2-methyl-2-pentenal, and 4-methyl-2-pentanol. In addition, the synthesized photocatalyst could successfully performed five consecutive photodegradation cycles. The obtained results revealed that the synthesized FeNi3@SiO2@ZnO magnetic nanocomposite holds a great potential to be applied as a photocatalyst for the degradation of TMX on an industrial scale.

Synthesis and characteristics of a novel FeNi3/SiO2/TiO2 magnetic nanocomposites and its application in adsorption of humic acid from simulated wastewater: study of isotherms and kinetics.

The presence of natural organic matter such as humic acid in water creates various problems in water purification. Humic acid can react with chlorine in the disinfection step and lead to the production of trihalomethanes and haloacetic acids that these compounds have carcinogenic and mutagenic properties; therefore, they must be removed before arriving to the disinfection stage. The purpose of this research was adsorption of humic acid from simulated wastewater by synthesized FeNi3/SiO2/TiO2 magnetic nanocomposites. FeNi3/SiO2/TiO2 magnetic nanocomposites were synthesized by sol-gel procedure and its characteristics were determined by TEM, VSM, BET, FESEM, and XRD techniques. Then, the effects of such pH (3-11), FeNi3/SiO2/TiO2 dosage (0.005-0.1 g/L), contact time (0-200 min), and initial concentration (2-15 mg/L) were studied on humic acid adsorption using FeNi3/SiO2/TiO2. The results of adsorption experiments revealed that the highest percentage of humic acid removal (94.4%) was achieved at pH 3, initial concentration of 5 ppm, FeNi3/SiO2/TiO2 dose of 0.1 g/L, and contact time of 90 min. The analyses of experimental isotherm data showed that the humic acid adsorption was described by Langmuir model and also the kinetic studies represented that the process of adsorption of humic acid on FeNi3/SiO2/TiO2 was followed by the pseudo-second kinetic. According to the results, it can be concluded that FeNi3/SiO2/TiO2 magnetic nanocomposites have a high ability to absorb humic acid from simulated wastewater.

A comparative study of using barberry stem powder and ash as adsorbents for adsorption of humic acid.

In the present research, investigation of the practical utility of barberry stem powder (BSP) and barberry stem ash (BSA) for humic acid (HA) removal from an aqueous medium by adsorption was carried out. The adsorption process was tested by varying of pH (3-11), reaction time (5-20 min), initial HA concentration (5-40 mg/L), adsorbent dosage (1-4 g/L), and temperature (15-35 °C). The isothermal results revealed that the adsorption process is favorable for both used adsorbents and it is highly described using the Freundlich and Langmuir models (R2 > 0.960). Also, the maximum uptakes of BSP and BSA for HA were 20.220 and 16.950 mg/g at the abovementioned optimized conditions (pH = 7, reaction time = 10 min, temperature = 15 °C, initial HA concentration = 40 mg/L, and adsorbent amount = 1.0 g/L), respectively. The results achieved from the fitting of the experimental data with Dubinin-Radushkevich isotherm model showed that the HA molecules are adsorbed onto the BSP and BSA by physiosorption process. From the thermodynamic study, it appeared that the biosorption process of the HA onto two studied adsorbents was of exothermic nature. The kinetics of the adsorption process of HA has been found to be pseudo-second-order model (R2 = 0.930-0.999). Thus, the results obtained from this paper elucidated that the BSP exhibited higher adsorption capacity in comparison to BSA, for HA removal up to permissible concentrations.

Facile green synthesis of silver nanoparticles using Berberis vulgaris leaf and root aqueous extract and its antibacterial activity.

Most recently, silver nanoparticles due to antibacterial properties have been considered in medical science. So the aim of the study was green synthesis of silver nanoparticles using Berberis vulgaris leaf and root aqueous extract and its antibacterial activity. After collection, identification and extraction of Berberis vulgaris was performed production of silver nanoparticles. In the study effect of parameters such as AgNO3 concentration (0.5, 1, 3, 10 mM), aqueous extract (3, 5, 10, 15, 30 mL) and contact time (1, 2, 6, 12, 24 h) were investigated in the synthesis of nanoparticles and also the antibacterial effect of these nanoparticles was studied on Escherichia coli and Staphylococcus aureus bacteria by Disk diffusion test and Minimum Inhibitory Concentration test (MIC). According to XRD results and analysis of TEM, nanoparticles have spherical shapes and size of 30 to 70 nm. On the other hand antibacterial tests showed these nanoparticles have more antibacterial activity more than other extracts. Result showed the biosynthesis of silver nanoparticles using aqueous extract of Berberis vulgaris is a clean, inexpensive and safe method that has not been used any toxic substance and consequently does not side effects and this nanoparticles has a high antibacterial activity.