RESUMEN
The vertical phase distribution of active layers plays a vital role in balancing exciton dissociation and charge transport for achieving efficient polymer solar cells (PSCs). The layer-by-layer (LbL) PSCs are commonly prepared by using sequential spin-coating method from donor and acceptor solutions with distinct solvents and solvent additives. The enhanced exciton dissociation is expected in the LbL PSCs with efficient charge transport in the relatively neat donor or acceptor layers. In this work, a series of LbL all-polymer solar cells (APSCs) were fabricated with PM6 as donor and PY-DT as acceptor, and triplet material m-Ir(CPmPB)3 is deliberately incorporated into PY-DT layer to prolong exciton lifetimes of active layers. The power conversion efficiency (PCE) of LbL APSCs is improved to 18.24% from 17.32% by incorporating 0.3 wt% m-Ir(CPmPB)3 in PY-DT layer, benefiting from the simultaneously enhanced short-circuit current density (JSC) of 25.17 mA cm-2 and fill factor (FF) of 74.70%. The enhancement of PCE is attributed to the efficient energy transfer of m-Ir(CPmPB)3 to PM6 and PY-DT, resulting in the prolonged exciton lifetime in the active layer and the increased exciton diffusion distance. The efficient energy transfer from m-Ir(CPmPB)3 to PM6 and PY-DT layer can be confirmed by the increased photoluminescence (PL) intensity and the prolonged PL lifetime of PM6 and PY-DT in PM6 + m-Ir(CPmPB)3 and PY-DT + m-Ir(CPmPB)3 films. This study indicates that the triplet material as solid additive has great potential in fabricating efficient LbL APSCs by prolonging exciton lifetimes in active layers.
RESUMEN
The large open circuit voltage (VOC) loss is currently one of the main obstacles to achieving efficient organic solar cells (OSCs). In this study, the ternary OSCs comprising PM6:BTP-eC9:IT-4F demonstrate a superior efficiency of 18.2 %. Notably, the utilization of the medium bandgap acceptor IT-4F as the third component results in an exceptionally low nonradiative recombination energy loss of 0.28â V. The desirable energy level cascade is formed among PM6, BTP-eC9, and IT-4F due to the low-lying HOMO and LUMO energy levels of IT-4F. More importantly, the VOC of PM6:BTP-eC9:IT-4F OSCs can reach as high as 0.86â V, which is higher than both binary OSCs without sacrificing JSC and FF. Besides, this strategy proved that IT-4F can not only broaden the absorption range but also work as a morphology modifier in PM6:BTP-eC9:IT-4F OSCs, and there also exists efficient energy transfer between BTP-eC9 and IT-4F. This result provides a promising way to suppress the nonradiative recombination energy loss and realize higher VOC than the two binary OSCs in ternary OSCs to obtain high power conversion efficiencies.
RESUMEN
Low bandgap organic semiconductors have been widely employed to broaden the light response range to utilize much more photons in the inverted perovskite solar cells (PSCs). However, the serious charge recombination at the heterointerface contact between perovskite and organic semiconductors usually leads to large energy loss and limits the device performance. In this work, a titanium chelate, bis(2,4-pentanedionato) titanium(IV) oxide (C10H14O5Ti), was directly used as an interlayer between the perovskite layer and organic bulk heterojunction layer for the first time. Impressively, it was found that C10H14O5Ti can not only increase the surface potential of perovskite films but also show a positive passivation effect toward the perovskite film surface. Drawing from the above function, a smoother perovskite active layer with a higher work function was realized upon the use of C10H14O5Ti. As a result, the C10H14O5Ti-modified integrated devices show lower interfacial loss and obtain the best power conversion efficiency (PCE) of up to 20.91% with a high voltage of 1.15 V. The research offers a promising strategy to minimize the interfacial loss for the preparation of high-performance perovskite solar cells.
RESUMEN
In this study, using PM6:L8-BO as the main system and non-fullerene acceptor IDIC as the third component, a series of ternary organic solar cells (TOSCs) are fabricated. The results reveal that IDIC plays a significant role in enhancing the performance of TOSCs by optimizing the morphology of blended films and forming interpenetrating nanostructure. The improved film morphology facilitates exciton dissociation and collection in TOSCs, which causes an increase in the short-circuit current density (JSC ) and fill factor (FF). Further, by optimizing the IDIC content, the power conversion efficiency (PCE) of TOSCs reaches 18.9%. Besides, the prepared TOSCs exhibit a JSC of 27.51 mA cm-2 and FF of 76.64%, which are much higher than those of PM6:L8-BO-based organic solar cells (OSCs). Furthermore, the addition of IDIC improves the long-term stability of the OSCs. Meanwhile, TOSCs with a large effective area of 1.00 cm2 have been prepared, which exhibit a PCE of 12.4%. These findings suggest that modifying the amount of the third component can be a useful strategy to construct hight-efficiency TOSCs with practical application potential.
RESUMEN
Additive strategies play a critical role in improving the performance of organic solar cells (OSCs). There are only a few reports on the application of solid additives for OSCs, which leaves a large space for further improvement of solid additives and further study on the relationship between material structure and property. PM6:BTP-eC9-based organic solar cells (OSCs) were prepared by using a small molecule BTA3 as a solid additive, and a high energy conversion efficiency of 18.65% is achieved. BTA3 has good compatibility with the acceptor component (BTP-eC9) and optimizes the morphology of the thin films. Moreover, the introduction of a small amount of BTA3 (5 wt %) effectively promotes exciton dissociation and charge transfer and suppresses charge recombination, and the relationship between the BTA3 content and the device parameter is deeply revealed. The use of BTA3 in the active layers is an attractive and effective strategy for high-performance OSCs.
RESUMEN
Carbon-based mesoscopic perovskite solar cells (MPSCs) are becoming one of the most competitive photovoltaic technologies owing to their lower manufacturing cost and excellent stability. In this work, methylammonium acetate (MAAc), an ionic liquid additive, is added into methylammonium lead triiodide (MAPbI3) perovskite and is used to fabricate high-performance MPSCs. Systematic and detailed studies have shown that the MAAc interacts with PbI2 preferentially to form a MAPbI3-x(Ac)x intermediate phase that can effectively control the crystallization kinetics of MAPbI3 in the triple-mesoscopic layer. MAPbI3 films with an appropriate amount of MAAc exhibit higher crystallinity, lower defect density, and dense pore filling, which effectively reduce carrier non-radiative recombination loss in MPSCs. As a result, a champion power conversion efficiency (PCE) of 13.54% is obtained based on the optimized MAAc-engineered MPSCs. The PCE is 24% higher than 10.90% of the control devices. Moreover, unencapsulated MAAc-engineered MPSCs retain 90% of their initial PCE after being stored in the dark for 50 days under ambient atmosphere, which demonstrates much better air stability than control devices. This work provides an effective strategy for developing efficient and stable carbon-based MPSCs with an eco-friendly ionic liquid additive.