Actionable insights into hazard mitigation of typical 3D printing waste via pyrolysis.

3D printing waste (3DPW) contains hazardous substances, such as photosensitizers and pigments, and may cause environmental pollution when improperly disposed of. Pyrolysis treatment can reduce hazards and turn waste into useful resources. This study coupled thermogravimetric (TG), TG-Fourier transform infrared spectroscopy-gas chromatography/mass spectrometry, and rapid pyrolysis gas chromatography/mass spectrometry analysis to evaluate the pyrolytic reaction mechanisms, products, and possible decomposition pathways of the three typical 3DPW of photosensitive resin waste (PRW), polyamide waste (PAW), and polycaprolactone waste (PCLW). The main degradation stages of the typical 3DPW occurred at 320-580 °C. The most appropriate reaction mechanisms of PRW, PAW and PCLW were D1, A1.2 and A1.5, respectively. The main pyrolysis processes were the decomposition of the complex organic polymers of PRW, the breaking of the NH-CH2 bond and dehydration of -CO-NH- of PAW, and the breaking and reorganization of the molecular chains of PCLW, mainly resulting in toluene (C7H8), undecylenitrile (C11H21N), tetrahydrofuran (C4H8O), respectively. Unlike the slow pyrolysis, the rapid pyrolysis produced volatiles consisting mainly of phenol, 4,4'-(1-methylethylidene)bis- (C15H16O2) for PRW; 1,10-dicyanodecane (C12H20N2) for PAW; and ɛ-caprolactone (C6H10O2) for PCLW. These pyrolysis products hold great potential for applications. The findings of the study offer actionable insights into the hazard reduction and resource recovery of 3D printing waste.

Tolerance limit of external beam radiotherapy combined with low-dose rate brachytherapy in normal rabbit tissue.

BACKGROUND: Dosage-optimized multimodal radiotherapies that are safe for head and neck cancer patients are desirable. In this study, we investigated tissue tolerance to varying doses of external beam radiotherapy (EBRT) combined with low-dose rate brachytherapy in the neck of a rabbit model. METHODS: Twenty rabbits were used in the four test groups (five each) with iodine-125 seeds implanted in the neck treated with EBRT in four doses at 50, 40, 30 and 20 Gy each. Twelve rabbits for three control groups (four each). Three months after implantation, all rabbits were euthanized, and target tissues were collected. Analyses included seed implantation assessment, histopathological evaluation, immunohistochemistry staining, terminal deoxynucleotidyl transferase dUTP nick end labeling assay, electron microscopy and statistics with the SPSS software. RESULTS: Five rabbits died in the four test groups, and three rabbits died in the three control groups (one per group), which showed no significant difference by survival analysis. The calculated minimum peripheral dose was 17.6 Gy, the maximum dose near the seed was 1812.5 Gy, the D90 was 34.5 Gy and the mean dose was 124.5 Gy. In all groups that received radiation, apoptosis occurred primarily in the esophageal mucosa and corresponded to the dose of radiation; a higher dose caused a greater apoptosis, with significant difference between groups (P < 0.05). Electron microscopy of carotid arteries revealed that endothelial cells were swollen and some were shed from basement membrane, but no other noticeable tissue damages. CONCLUSIONS: Limited EBRT at maximal dose (50 Gy) combined with the brachytherapy interstitially applied to the neck was tolerated well in the rabbit model.

Ultrahigh-Loading Manganese-Based Electrodes for Aqueous Batteries via Polymorph Tuning.

Manganese-based aqueous batteries utilizing Mn2+ /MnO2 redox reactions are promising choices for grid-scale energy storage due to their high theoretical specific capacity, high power capability, low-cost, and intrinsic safety with water-based electrolytes. However, the application of such systems is hindered by the insulating nature of deposited MnO2 , resulting in low normalized areal loading (0.005-0.05 mAh cm-2 ) during the charge/discharge cycle. In this work, the electrochemical performance of various MnO2 polymorphs in Mn2+ /MnO2 redox reactions is investigated, and ɛ-MnO2 with low conductivity is determined to be the primary electrochemically deposited phase in normal acidic aqueous electrolyte. It is found that increasing the temperature can change the deposited phase from ɛ-MnO2 with low conductivity to γ-MnO2 with two order of magnitude increase in conductivity. It is demonstrated that the highly conductive γ-MnO2 can be effectively exploited for ultrahigh areal loading electrode, and a normalized areal loading of 33 mAh cm-2 is achieved. At a mild temperature of 50 °C, cells are cycled with an ultrahigh areal loading of 20 mAh cm-2 (1-2 orders of magnitude higher than previous studies) for over 200 cycles with only 13% capacity loss.

Prediction of response to preoperative neoadjuvant chemotherapy in extremity high-grade osteosarcoma using X-ray and multiparametric MRI radiomics.

PURPOSE: This study aims to evaluate the value of applying X-ray and magnetic resonance imaging (MRI) models based on radiomics feature to predict response of extremity high-grade osteosarcoma to neoadjuvant chemotherapy (NAC). MATERIALS AND METHODS: A retrospective dataset was assembled involving 102 consecutive patients (training dataset, n = 72; validation dataset, n = 30) diagnosed with extremity high-grade osteosarcoma. The clinical features of age, gender, pathological type, lesion location, bone destruction type, size, alkaline phosphatase (ALP), and lactate dehydrogenase (LDH) were evaluated. Imaging features were extracted from X-ray and multi-parametric MRI (T1-weighted, T2-weighted, and contrast-enhanced T1-weighted) data. Features were selected using a two-stage process comprising minimal-redundancy-maximum-relevance (mRMR) and least absolute shrinkage and selection operator (LASSO) regression. Logistic regression (LR) modelling was then applied to establish models based on clinical, X-ray, and multi-parametric MRI data, as well as combinations of these datasets. Each model was evaluated using sensitivity, specificity, and area under the receiver operating characteristic curve (AUC) with a 95% confidence interval (CI). RESULTS: AUCs of 5 models using clinical, X-ray radiomics, MRI radiomics, X-ray plus MRI radiomics, and combination of all were 0.760 (95% CI: 0.583-0.937), 0.706 (95% CI: 0.506-0.905), 0.751 (95% CI: 0.572-0.930), 0.796 (95% CI: 0.629-0.963), 0.828 (95% CI: 0.676-0.980), respectively. The DeLong test showed no significant difference between any pair of models (p > 0.05). The combined model yielded higher performance than the clinical and radiomics models as demonstrated by net reclassification improvement (NRI) and integrated difference improvement (IDI) values, respectively. This combined model was also found to be clinically useful in the decision curve analysis (DCA). CONCLUSION: Modelling based on combination of clinical and radiomics data improves the ability to predict pathological responses to NAC in extremity high-grade osteosarcoma compared to the models based on either clinical or radiomics data.

Onboard early detection and mitigation of lithium plating in fast-charging batteries.

Fast-charging is considered as one of the most desired features needed for lithium-ion batteries to accelerate the mainstream adoption of electric vehicles. However, current battery charging protocols mainly consist of conservative rate steps to avoid potential hazardous lithium plating and its associated parasitic reactions. A highly sensitive onboard detection method could enable battery fast-charging without reaching the lithium plating regime. Here, we demonstrate a novel differential pressure sensing method to precisely detect the lithium plating event. By measuring the real-time change of cell pressure per unit of charge (dP/dQ) and comparing it with the threshold defined by the maximum of dP/dQ during lithium-ion intercalation into the negative electrode, the onset of lithium plating before its extensive growth can be detected with high precision. In addition, we show that by integrating this differential pressure sensing into the battery management system (BMS), a dynamic self-regulated charging protocol can be realized to effectively extinguish the lithium plating triggered by low temperature (0 °C) while the conventional static charging protocol leads to catastrophic lithium plating at the same condition. We propose that differential pressure sensing could serve as an early nondestructive diagnosis method to guide the development of fast-charging battery technologies.

Cold-Starting All-Solid-State Batteries from Room Temperature by Thermally Modulated Current Collector in Sub-Minute.

All-solid-state batteries (ASSBs) show great potential as high-energy and high-power energy-storage devices but their attainable energy/power density at room temperature is severely reduced because of the sluggish kinetics of lithium-ion transport. Here a thermally modulated current collector (TMCC) is reported, which can rapidly cold-start ASSBs from room temperature to operating temperatures (70-90 °C) in less than 1 min, and simultaneously enhance the transient peak power density by 15-fold compared to one without heating. This TMCC is prepared by integrating a uniform, ultrathin (≈200 nm) nickel layer as a thermal modulator within an ultralight polymer-based current collector. By isolating the thermal modulator from the ion/electron pathway of ASSBs, it can provide fast, stable heat control yet does not interfere with regular battery operation. Moreover, this ultrathin (13.2 µm) TMCC effectively shortens the heat-transfer pathway, minimizes heat losses, and mitigates the formation of local hot spots. The simulated heating energy consumption can be as low as ≈3.94% of the total battery energy. This TMCC design with good tunability opens new frontiers toward smart energy-storage devices in the future from the current collector perspective.

[Nasal endoscopy assisting combined with transoral approach for resection of carcinoma of the palate invading nasal cavity and sinuses].

Objective:To explore the value of nasal endoscopy assisting combined with transoral approach in resection of the carcinoma of the palate with the nasal cavity and sinuses invaded. Methods:A retrospective analysis of 21 patients with a primary malignant tumors of the palate was performed. Preoperative nasal endoscopy and CT and MRI scan showed that the primary tumors invading the nasal cavity and sinuses in all patients or skull base with varying degrees. All patients were treated by nasal endoscopic assisting combined with transoral approach. Postoprational adjuvant radiotherapy or concurrent chemoradiotherapy was performed according to pathological types and clinical stage. Postoperative complications, all-tumor resection rate, local control rate and 5-year survival rate were analyzed statistically. Results:The combined approach was successfully performed in all patients. En bloc resection was carried out in 18 patients by this combined approach and surgical margins were free of carcinoma. The median follow-up period was 60 months. All patients had good nasal ventilation function and no epiphora in postoperation, and the overall local control rate of primary site was 85.7%, overall 5-year survival rate was 76.2%. Conclusion:Nasal endoscopy assisting combined with transoral approach is an effective method for the resection of palate malignant tumors invading the nasal cavity and sinuses. It is convenient for en bloc resection and local control of primary lesions. It is beneficial to preserve the function of nasal cavity and sinuses, which is in line with the principle of functional surgery.

Oxy-fuel co-combustion dynamics of phytoremediation biomass and textile dyeing sludge: Gas-to-ash pollution abatement.

The environmental pressures of major wastes in the circular economies can be abated leveraging the complementarity and optimal conditions of their co-combustion. The oxy-fuel co-combustion of phytoremediation biomass of Sedum alfredii Hance (SAH) and textile dyeing sludge (TDS) may be a promising choice for sustainable CO2 capture and a waste-to-energy conversion. This study characterized and quantified their co-combustion performances, kinetics, and interactions as a function of blend ratio, atmosphere type, and temperature. With a focus on the characteristic elements of SAH (Ca, K, Zn, and Cd) and TDS (Al and S), changes in the mineral phases and ash melting and slagging trends of K2O-Al2O3-SiO2 and CaO-Al2O3-SiO2 systems were quantified. The Zn and Cd residual rates of the co-combustion of 75% SAH and 25% TDS rose by 58.52% and 5.93%, respectively, in the oxy-fuel atmosphere at the 30% oxygen concentration, relative to the mono-combustion of SAH in the air atmosphere. The co-combustion in the oxy-fuel atmosphere at the 20% oxygen concentration delayed the release peaks of SO2, C2S, and H2S, while the Ca-rich SAH captured S in TDS through the formation of CaSO4. Our findings provide new and practical insights into the oxy-fuel co-combustion toward the enhanced co-circularity.

Dynamic spatial progression of isolated lithium during battery operations.

The increasing demand for next-generation energy storage systems necessitates the development of high-performance lithium batteries1-3. Unfortunately, current Li anodes exhibit rapid capacity decay and a short cycle life4-6, owing to the continuous generation of solid electrolyte interface7,8 and isolated Li (i-Li)9-11. The formation of i-Li during the nonuniform dissolution of Li dendrites12 leads to a substantial capacity loss in lithium batteries under most testing conditions13. Because i-Li loses electrical connection with the current collector, it has been considered electrochemically inactive or 'dead' in batteries14,15. Contradicting this commonly accepted presumption, here we show that i-Li is highly responsive to battery operations, owing to its dynamic polarization to the electric field in the electrolyte. Simultaneous Li deposition and dissolution occurs on two ends of the i-Li, leading to its spatial progression toward the cathode (anode) during charge (discharge). Revealed by our simulation results, the progression rate of i-Li is mainly affected by its length, orientation and the applied current density. Moreover, we successfully demonstrate the recovery of i-Li in Cu-Li cells with >100% Coulombic efficiency and realize LiNi0.5Mn0.3Co0.2O2 (NMC)-Li full cells with extended cycle life.

Integrated cooling (i-Cool) textile of heat conduction and sweat transportation for personal perspiration management.

Perspiration evaporation plays an indispensable role in human body heat dissipation. However, conventional textiles tend to focus on sweat removal and pay little attention to the basic thermoregulation function of sweat, showing limited evaporation ability and cooling efficiency in moderate/profuse perspiration scenarios. Here, we propose an integrated cooling (i-Cool) textile with unique functional structure design for personal perspiration management. By integrating heat conductive pathways and water transport channels decently, i-Cool exhibits enhanced evaporation ability and high sweat evaporative cooling efficiency, not merely liquid sweat wicking function. In the steady-state evaporation test, compared to cotton, up to over 100% reduction in water mass gain ratio, and 3 times higher skin power density increment for every unit of sweat evaporation are demonstrated. Besides, i-Cool shows about 3 °C cooling effect with greatly reduced sweat consumption than cotton in the artificial sweating skin test. The practical application feasibility of i-Cool design principles is well validated based on commercial fabrics. Owing to its exceptional personal perspiration management performance, we expect the i-Cool concept can provide promising design guidelines for next-generation perspiration management textiles.

A Morphologically Stable Li/Electrolyte Interface for All-Solid-State Batteries Enabled by 3D-Micropatterned Garnet.

Morphological degradation at the Li/solid-state electrolyte (SSE) interface is a prevalent issue causing performance fading of all-solid-state batteries (ASSBs). To maintain the interfacial integrity, most ASSBs are operated under low current density with considerable stack pressure, which significantly limits their widespread usage. Herein, a novel 3D-micropatterned SSE (3D-SSE) that can stabilize the morphology of the Li/SSE interface even under relatively high current density and limited stack pressure is reported. Under the pressure of 1.0 MPa, the Li symmetric cell using a garnet-type 3D-SSE fabricated by laser machining shows a high critical current density of 0.7 mA cm-2 and stable cycling over 500 h under 0.5 mA cm-2 . This excellent performance is attributed to the reduced local current density and amplified mechanical stress at the Li/3D-SSE interface. These two effects can benefit the flux balance between Li stripping and creep at the interface, thereby preventing interfacial degradation such as void formation and dendrite growth.

Electrolyte-Resistant Dual Materials for the Synergistic Safety Enhancement of Lithium-Ion Batteries.

Safety issues associated with lithium-ion batteries are of major concern, especially with the ever-growing demand for higher-energy-density storage devices. Although flame retardants (FRs) added to electrolytes can reduce fire hazards, large amounts of FRs are required and they severely deteriorate battery performance. Here, we report a feasible method to balance flame retardancy and electrochemical performance by coating an electrolyte-insoluble FR on commercial battery separators. By integrating dual materials via a two-pronged mechanism, the quantity of FR required could be limited to an ultrathin coating layer (4 µm) that rarely influences electrochemical performance. The developed composite separator has a four-times better flame retardancy than conventional polyolefin separators in full pouch cells. Additionally, this separator can be fabricated easily on a large scale for industrial applications. High-energy-density batteries (2 Ah) were assembled to demonstrate the scaling of the composite separator and to confirm its enhanced safety through nail penetration tests.

Rapid solidification of Sr-contaminated soil by consecutive microwave sintering: mechanism and stability evaluation.

Consecutive microwave sintering is a method proposed in this study to dispose soil contaminated by Sr during a nuclear accident by rapidly solidifying the contaminated soil. The results show that soil contaminated with 20 wt% SrSO4 and 30 wt% SrSO4 can be completely solidified by microwave sintering at 1100-1200 and 1300 â„ƒ, respectively, for 30 min. Sr was found to be cured into slawsonite (SrAl2Si2O8) and glass structures. Moreover, soil sintered at 1300 â„ƒ has large cured solubility (30 wt.%), good uniformity, and excellent hardness (6.9-7.2 GPa) and chemical durability (below 1.46 × 10-5 g m-2 d-1 at 28 d). Thus, consecutive microwave sintering technology may provide a new method for treating Sr-contaminated soil in case of a nuclear accident emergency.

Designing a Nanoscale Three-phase Electrochemical Pathway to Promote Pt-catalyzed Formaldehyde Oxidation.

Gas-phase heterogeneous catalysis is a process spatially constrained on the two-dimensional surface of a solid catalyst. Here, we introduce a new toolkit to open up the third dimension. We discovered that the activity of a solid catalyst can be dramatically promoted by covering its surface with a nanoscale-thin layer of liquid electrolyte while maintaining efficient delivery of gas reactants, a strategy we call three-phase catalysis. Introducing the liquid electrolyte converts the original surface catalytic reaction into an electrochemical pathway with mass transfer facilitated by free ions in a three-dimensional space. We chose the oxidation of formaldehyde as a model reaction and observed a 25000-times enhancement in the turnover frequency of Pt in three-phase catalysis as compared to conventional heterogeneous catalysis. We envision three-phase catalysis as a new dimension for catalyst design and anticipate its applications in more chemical reactions from pollution control to the petrochemical industry.

Modified Maxillary-Swing Approach for Resection of Primary Malignancies in the Pterygopalatine Fossa.

BACKGROUND: En bloc resection of malignancies in the pterygopalatine fossa (PPF) poses critical challenges. Using the modified maxillary-swing (MMS) approach, we achieved monobloc removal of primary malignancies in this region. This study provides a detailed account of the surgical techniques and indications used. METHODS: We enrolled seven patients with primary malignancies in the PPF during a period from January 2012 to January 2019 in this retrospective study. After malignancies were confirmed by biopsy as well as evaluation with computed tomography (CT) and magnetic resonance imaging (MRI) scans, all of the patients underwent MMS surgery under general anesthesia to extirpate these tumors. We performed regular postoperative follow-up using CT and MRI scans. RESULTS: En bloc resection was successfully performed in all cases. We observed negative margins in six cases and positive margins in one patient with adenoid cystic carcinoma, who received postoperative radiotherapy. The most common complication was facial numbness. During the follow-up period (range, 6-69 months), one patient suffered from recurrence, while the others did not. CONCLUSION: The advantages of the MMS include a wide surgical field, full exposure, and easy manipulation. We expect this approach to become an alternative to the monobloc resection of malignancies in the PPF that involve the infratemporal fossa, maxillary sinus, nasal cavity, orbit, or oral cavity.

Targeted Inhibitory Effect of Nasopharyngeal Carcinoma Cells by Hre2.Grp78 Chimeric Promoter Regulating Fusion Gene TK/VP3.

OBJECTIVE: To construct plasmids with Hre2.Grp78 chimeric promoter regulating fusion gene TK/VP3 and elaborate the effects of overexpressed TK/VP3 on nasopharyngeal carcinoma cells. METHODS: Four plasmids were constructed, including pcDNA3.1-CMV-TK/VP3, pcDNA3.1-Hre2.TK/VP3, pcDNA3.1-Grp78.TK/VP3, and pcDNA3.1-Hre2.Grp78.TK/VP3. The human nasopharyngeal carcinoma cell line HNE1 cells were transfected with the 4 plasmids, respectively. Cell viabilities were evaluated using 3-(4,5-Dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay, and apoptosis was conducted using flow cytometry analysis. The expression of TK, VP3, Grp78, and hypoxia-inducible factor 1α and apoptosis-related proteins was determined by real-time quantitative polymerase chain reaction and Western blotting. RESULTS: The recombinant plasmids that could steadily overexpress TK and VP3 were successfully constructed. Expression of TK and VP3 in cells transfected with pcDNA3.1-Hre2.TK/VP3 and pcDNA3.1-Grp78.TK/VP3 was significantly higher than pcDNA3.1-CMV-TK/VP3, and expression in cells transfected with pcDNA3.1-Hre2.Grp78.TK/VP3 was the highest. Under glucose deprivation or hypoxia condition, Grp78 or hypoxia-inducible factor 1α was overexpressed so that expression of TK and VP3 was significantly upregulated, which could further inhibit cell proliferation and enhance cell apoptosis. CONCLUSION: We successfully constructed 4 plasmids with Hre2.Grp78 chimeric promoter regulating fusion gene TK/VP3, which could significantly inhibit the proliferation as well as enhance the apoptosis of nasopharyngeal carcinoma cells under glucose deprivation or hypoxia condition.

Numb inhibits epithelial-mesenchymal transition via RBP-Jκ-dependent Notch1/PTEN/FAK signaling pathway in tongue cancer.

BACKGROUND: Oral cancer has been estimated as the sixth most frequent solid cancer all over the world, in which tongue squamous cell carcinoma (TSCC) is the most common type of oral cancers. However, the mechanism of TSCC metastasizing to lymph node and distant sites has not been completely understood. METHODS: In this study, RT-qPCR method was used to detect the mRNA level of Numb, PTEN and Notch1 genes, as well as EMT-associated genes. Western blot assay was utilized to detect protein level of these genes. In addition, we determined cell proliferation by MTT assay and employed transwell invasion assay and wound healing assay to probe the abilities of invasion and migration, respectively. To investigate the role of PTEN, its inhibitor VO-Ohpic trihydrate was used to treat SCC-4 and CAL27 cells. RESULTS: We found that Numb expression was downregulated in SCC-9 and CAL-27 cells compared to NHOK cells. Instead, Notch1 level in SCC-9 and CAL-27 cells were higher than that in NHOK cells. Furthermore, the results showed that Numb overexpression significantly suppressed proliferation, migration and invasion of SCC-9 and CAL-27 cells via regulating Notch1 signaling and EMT-related genes expression. By contrast, we observed that RBP-Jκ knockdown had an inhibitory role in proliferation, migration and invasion of SCC-9 and CAL-27 cells. In cells with Numb overexpression or RBP-Jκ knockdown, p-FAK and EMT-related genes were remarkably regulated. CONCLUSIONS: Our findings provide new mechanism of understanding the metastasis of TSCC and help develop therapeutic strategies for treating tongue cancer.

Unravelling Atomic Structure and Degradation Mechanisms of Organic-Inorganic Halide Perovskites by Cryo-EM.

Despite rapid progress of hybrid organic-inorganic halide perovskite solar cells, using transmission electron microscopy to study their atomic structures has not been possible because of their extreme sensitivity to electron beam irradiation and environmental exposure. Here, we develop cryogenic-electron microscopy (cryo-EM) protocols to preserve an extremely sensitive perovskite, methylammonium lead iodide (MAPbI3) under various operating conditions for atomic-resolution imaging. We discover the precipitation of lead iodide nanoparticles on MAPbI3 nanowire's surface after short UV illumination and surface roughening after only 10 s exposure to air, while these effects remain undetected in conventional x-ray diffraction. We establish a definition for critical electron dose, and find this value for MAPbI3 at cryogenic condition to be 12 e-/Å2 at 1.49 Å spatial resolution. Our results highlight the importance of cryo-EM since traditional techniques cannot capture important nanoscale changes in morphology and structure that have important implications for perovskite solar cell stability and performance.

Wearable Thermoelectric Devices Based on Au-Decorated Two-Dimensional MoS2.

Two-dimensional (2D) materials have recently opened a new avenue to flexible thermoelectric materials with enhanced performance because of their unique electronic transport properties. Here, we report a feasible approach to improve the thermoelectric performance of transition-metal dichalcogenides by effectively decorating 2D MoS2 with Au nanoparticles using in situ growth. The present Au-decorated MoS2-assembled heterojunction system shows a certain decoupled phenomenon, that is, the Seebeck coefficient and conductivity increased simultaneously. This is due to the occurrence of p-type doping of the MoS2 2H phase and injection energy filtering of dopant-originated carriers around the local band bending at the interface. The composite flexible films can achieve a power factor value of 166.3 µW m-1 K-2 at room temperature, which have great potential for harvesting human body heat.