Investigations of Shape Deformation Behaviors of the Ferromagnetic Ni-Mn-Ga Alloy/Porous Silicone Rubber Composite towards Actuator Applications.

Ferromagnetic shape memory alloys (FSMAs), which are potential candidates for future technologies (i.e., actuators in robots), have been paid much attention for their high work per volume and rapid response as external stimulation, such as a magnetic field, is imposed. Among all the FSMAs, the Ni-Mn-Ga-based alloys were considered promising materials due to their appropriate phase transformation temperatures and ferromagnetism. Nevertheless, their intrinsic embrittlement issue and sluggish twin motion due to the inhibition of grain boundaries restrict their practicability. This study took advantage of the single-crystal Ni-Mn-Ga cube/silicone rubber composite materials to solve the two aforementioned difficulties. The single-crystal Ni-Mn-Ga cube was prepared by using a high-temperature alloying procedure and a floating-zone (FZ) method, and the cubes were verified to be the near-{100}p Ni-Mn-Ga alloy. Various room temperature (RT) curing silicone rubbers were utilized as matrix materials. Furthermore, polystyrene foam particles (PFP) were used to provide pores, allowing a porous silicone rubber matrix. It was found that the elastic modulus of the silicone rubber was successfully reduced by introducing the PFP. Additionally, the magnetic field-induced martensite variant reorientation (MVR) was greatly enhanced by introducing a porous structure into the silicone rubber. The single-crystal Ni-Mn-Ga cube/porous silicone rubber composite materials are considered to be promising materials for applications in actuators.

Promoted mechanical properties and functionalities via Ta-tailored Ti-Au-Cr shape memory alloys towards biomedical applications.

In view of the urgent demands of shape memory alloys (SMAs) for biomedical applications due to the world population aging issue, the mechanical properties and functionalities of the biocompatible Ti-Au-Cr-based SMAs, which are tailored by Ta additions, have been developed in this study. The quaternary SMAs were successfully manufactured by physical metallurgy techniques and their mechanical properties and functionalities were examined. In the continuous tensile tests, it was found that the correlation between the yielding strength and phase stability followed a typical trend of mechanical behavior of SMAs, showing the lowest yielding strength at the metastable ß-parent phase. Functional mappings between the alloy strength and elongation revealed that compared to the Ta-free specimen, the ductility was promoted 50% while the strength remained intact through the 4 at.% introduction of Ta. Slight shape recovery was observed in the cyclic loading-unloading tensile tests during the unloading process and the highest shape recovery was found in the Ti-4 at.% Au-5 at.% Cr-4 at.% Ta specimen. This indicates that the 4 at.% Ta tailored Ti-Au-Cr SMAs could be a promising material for biomedical applications.

Investigations of Effects of Intermetallic Compound on the Mechanical Properties and Shape Memory Effect of Ti-Au-Ta Biomaterials.

Owing to the world population aging, biomedical materials, such as shape memory alloys (SMAs) have attracted much attention. The biocompatible Ti-Au-Ta SMAs, which also possess high X-ray contrast for the applications like guidewire utilized in surgery, were studied in this work. The alloys were successfully prepared by physical metallurgy techniques and the phase constituents, microstructures, chemical compositions, shape memory effect (SME), and superelasticity (SE) of the Ti-Au-Ta SMAs were also examined. The functionalities, such as SME, were revealed by the introduction of the third element Ta; in addition, obvious improvements of the alloy performances of the ternary Ti-Au-Ta alloys were confirmed while compared with that of the binary Ti-Au alloy. The Ti3Au intermetallic compound was both found crystallographically and metallographically in the Ti-4 at.% Au-30 at.% Ta alloy. The strength of the alloy was promoted by the precipitates of the Ti3Au intermetallic compound. The effects of the Ti3Au precipitates on the mechanical properties, SME, and SE were also investigated in this work. Slight shape recovery was found in the Ti-4 at.% Au-20 at.% Ta alloy during unloading of an externally applied stress.

Enhancement of mechanical properties and shape memory effect of Ti-Cr-based alloys via Au and Cu modifications.

The requirements for biomedical materials have been raised greatly due to the rapidly aging global population. Shape memory alloys (SMAs) are indeed promising materials for biomedical applications due to their controllable shape deformation via the manipulation of temperature and/or stress. This study investigated the enhancement of the fundamental mechanical properties and the shape memory effect (SME) in the Ti-Cr-based alloys via the modification of Au and Cu. The quaternary Ti-Cr-Au-Cu alloys were successfully manufactured by physical metallurgy methods and their phase constitutions, mechanical properties, SME, and superelastic (SE) behaviors have been investigated in this study. Cold-workability, which was enhanced by the introduction of the Au element, was elaborated by the phase constitutions of the alloys. The ß-parent phase was stabilized to around body temperature by the introduction of the ß-stabilizers of Cr, Au, and Cu, and the functionalities of the specimens were revealed at the operating temperature. Perfect SME at the shape recovery rate of 100% was practiced by the substitution of Au by Cu and the mechanical properties, such as strength and ductility, were also enhanced. Functional mappings of the fundamental mechanical properties, which could be a helpful tool for the investigations of the quaternary Ti-Cr-Au-Cu alloys, were constructed in this work.

Analysis of variant-pairing tendencies in lenticular martensite microstructures based on rank-1 connection.

Herein, variant-pairing tendencies of lenticular martensite in an Fe-30Ni-0.3C (wt%) alloy are analyzed based on rank-1 connection at martensite/martensite junction planes (JPs) to facilitate the understanding of martensite microstructure. The degree of incompatibility (θ) at the JPs successfully explained their observed frequency; in the actual microstructure, variant pairs with a small θ form preferentially. The experimentally obtained JPs were consistent with theoretical ones. To the best of our knowledge, this is the first study to confirm the validity of variant-pair crystallography in steel based on rank-1 connection, both theoretically and experimentally. Diamond, composite-spear, and composite-kink clusters are considered. The cumulative θ at the JPs can suppress diamond cluster formation because it exceeds the θ of a single variant pair, and the diamond cluster is not observed experimentally. However, θ at the JPs cancel out in composite-spear (CS) and composite-kink (CK) clusters, but CK clusters are rarely observed experimentally, while a few CS clusters are observed. This demonstrates the analytical limitations of 2D approaches used to evaluate the frequency of variant pairs and clusters. These two variant clusters have a narrow window of 2D observation because the orientation relationships between JPs and intersection lines between two habit planes affect the areas of JPs.

Plastic deformation behaviour of single-crystalline martensite of Ti-Nb shape memory alloy.

ß-Ti alloys have attracted considerable attention as new biomedical shape memory alloys. Given the critical importance of the plastic deformation in the martensite phase for the shape memory effect and superelasticity, we investigated here the plastic deformation behaviour of a single crystal of α″ (orthorhombic) martensite of Ti-27 mol%Nb shape memory alloy obtained by the stress-induced martensitic transformation of a single crystal of the parent ß phase. Four operative plastic deformation modes were observed, including two dislocation slips and two twinnings. To the best of our knowledge, two of these plastic deformation modes (one dislocation slip and one twinning) were discovered for the first time in this study. The identified slip and twinning systems in the martensite phase have corresponding slip and twinning systems in the parent ß phase with which they share many similarities. Therefore, we believe that the plastic deformation of the α″ martensite is inherited from that of the parent ß phase.