Electrospun Amphiphilic Nanofibers as Templates for In Situ Preparation of Chloramphenicol-Loaded Liposomes.

The hydration of phospholipids, electrospun into polymeric nanofibers and used as templates for liposome formation, offers pharmaceutical advantages as it avoids the storage of liposomes as aqueous dispersions. The objective of the present study was to electrospin and characterize amphiphilic nanofibers as templates for the preparation of antibiotic-loaded liposomes and compare this method with the conventional film-hydration method followed by extrusion. The comparison was based on particle size, encapsulation efficiency and drug-release behavior. Chloramphenicol (CAM) was used at different concentrations as a model antibacterial drug. Phosphatidylcoline (PC) with polyvinylpyrrolidone (PVP), using ethanol as a solvent, was found to be successful in fabricating the amphiphilic composite drug-loaded nanofibers as well as liposomes with both methods. The characterization of the nanofiber templates revealed that fiber diameter did not affect the liposome size. According to the optical microscopy results, the immediate hydration of phospholipids deposited on the amphiphilic nanofibers occurred within a few seconds, resulting in the formation of liposomes in water dispersions. The liposomes appeared to aggregate more readily in the concentrated than in the diluted solutions. The drug encapsulation efficiency for the fiber-hydrated liposomes varied between 14.9 and 28.1% and, for film-hydrated liposomes, between 22.0 and 77.1%, depending on the CAM concentrations and additional extrusion steps. The nanofiber hydration method was faster, as less steps were required for the in-situ liposome preparation than in the film-hydration method. The liposomes obtained using nanofiber hydration were smaller and more homogeneous than the conventional liposomes, but less drug was encapsulated.

Old drug, new wrapping - A possible comeback for chloramphenicol?

The antimicrobial drug chloramphenicol (CAM) exhibits activity against resistant bacteria, such as methicillin-resistant Staphylococcus aureus (MRSA). However, its use has been limited due to its toxicity. As the threat of antibiotic resistance continues to grow, a promising approach might be to increase the use of historical antimicrobial agents that demonstrate clinical efficacy, but are hampered by toxicity. We therefore aimed to prepare a liposome-in-hydrogel system for dermal delivery of CAM. Chitosan (CS) was used as the hydrogel vehicle due to its antimicrobial activity and excellent biocompatibility. All critical preparation steps were carried out by dual centrifugation (DC). The DC-method proved to be fast and simple, and organic solvents were avoided in all processing steps. Liposomes with high drug entrapment (49-56%), low polydispersity and a size of approximately 120nm were produced. Mixing of liposomes into CS-hydrogel by DC produced a homogenous liposomes-in-hydrogel system. Bioadhesive properties were good and comparable to plain CS-hydrogel formulations. Ex vivo permeation studies using pig skin indicated a sustained release of CAM and limited skin permeation. The in vitro antimicrobial activity of CAM in the new liposome-in-hydrogel formulation was similar or better as compared to CAM in solution. Thus, the new formulation was considered highly promising.

Successful co-encapsulation of benzoyl peroxide and chloramphenicol in liposomes by a novel manufacturing method - dual asymmetric centrifugation.

Encapsulation of more than one active pharmaceutical ingredient into nanocarriers such as liposomes is an attractive approach to achieve a synergic drug effect and less complicated dosing schedules in multi-drug treatment regimes. Liposomal drug delivery in acne treatment may improve drug efficiency by targeted delivery to pilosebaceous units, reduce adverse effects and improve patient compliance. We therefore aimed to co-encapsulate benzoyl peroxide (BPO) and chloramphenicol (CAM) into liposomes using the novel liposome processing method - dual asymmetric centrifugation (DAC). Liposomes were formed from soybean lecithin, propylene glycol and distilled water (2:1:2w/v/v ratio), forming a viscous liposome dispersion. Liposomes containing both drugs (BPO-CAM-Lip), single drug (BPO-Lip and CAM-Lip), and empty liposomes were prepared. Drug entrapment of BPO and CAM was determined by a newly developed HPLC method for simultaneous detection and quantification of both drugs. Encapsulation of around 50% for BPO and 60% for CAM respectively was obtained in both single-drug encapsulated formulations (BPO-Lip and CAM-Lip) and co-encapsulated formulations (BPO-CAM-Lip). Liposome sizes were comparable for all liposome formulations, ranging from 130 to 150nm mean diameter, with a polydispersity index <0.2 for all formulations. CAM exhibited a sustained release from all liposomal formulations, whereas BPO appeared retained within the liposomes. BPO retention could be attributed to its poor solubility. However, HaCaT cell toxicity was found dependent on BPO released from the liposomes. In the higher concentration range (4%v/v), liposomal formulations were less cytotoxic than the corresponding drug solutions used as reference. We have demonstrated that DAC is a fast, easy, suitable method for encapsulation of more than one drug within the same liposomes.

Development of Suberin Fatty Acids and Chloramphenicol-Loaded Antimicrobial Electrospun Nanofibrous Mats Intended for Wound Therapy.

Suberin fatty acids (SFAs) isolated from outer birch bark were investigated as an antimicrobial agent and biomaterial in nanofibrous mats intended for wound treatment. Electrospinning (ES) was used in preparing the composite nonwoven nanomats containing chloramphenicol (CAM; as a primary antimicrobial drug), SFAs, and polyvinylpyrrolidone (as a carrier polymer for ES). The X-ray powder diffraction, differential scanning calorimetry, scanning electron microscopy, atomic force microscopy, and texture analysis were used for the physicochemical and mechanical characterization of the nanomats. ES produced nanofibrous mats with uniform structure and with an average fiber diameter ranging from 370 to 425 nm. Microcrystalline SFAs and crystalline CAM were found to undergo a solid-state transformation during ES processing. The ES process caused also the loss of CAM in the final nanofibers. In the texture analysis, the SFAs containing nanofibers exhibited significantly higher maximum detachment force to an isolated pig skin (p < 0.05) than that obtained with the reference nanofibers. CAM exists in an amorphous form in the nanofibers which needs to be taken into account in controlling the physical storage stability. In conclusion, homogeneous composite nanofibrous mats for wound healing can be electrospun from the ternary mixture(s) of CAM, SFAs, and polyvinylpyrrolidone.

Development and optimization of a new processing approach for manufacturing topical liposomes-in-hydrogel drug formulations by dual asymmetric centrifugation.

OBJECTIVE: The objective of the present study was to utilize dual asymmetric centrifugation (DAC) as a novel processing approach for the production of liposomes-in-hydrogel formulations. MATERIALS AND METHODS: Lipid films of phosphatidylcholine, with and without chloramphenicol (CAM), were hydrated and homogenized by DAC to produce liposomes in the form of vesicular phospholipid gels with a diameter in the size range of 200-300 nm suitable for drug delivery to the skin. Different homogenization processing parameters were investigated along with the effect of adding propylene glycol (PG) to the formulations prior to homogenization. The produced liposomes were incorporated into a hydrogel made of 2.5% (v/v) soluble ß-1,3/1,6-glucan (SBG) and mixed by DAC to achieve a homogenous liposomes-in-hydrogel-formulation suitable for topical application. RESULTS AND DISCUSSION: CAM-containing liposomes with a vesicle diameter of 282 ± 30 nm and polydispersity index (PI) of 0.13 ± 0.02 were successfully produced by DAC after 50 min centrifugation at 3500 rpm, and homogenously (< 4% content variation) incorporated into the SBG hydrogel. Addition of PG decreased the necessary centrifugation time to 2 min and 55 s, producing liposomes of 230 ± 51 nm and PI of 0.25 ± 0.04. All formulations had an entrapment efficiency of approximately 50%. CONCLUSION: We managed to develop a relatively fast and reproducible new method for the production of liposomes-in-hydrogel formulations by DAC.

Investigation of parameters influencing incorporation, retention and cellular cytotoxicity in liposomal formulations of poorly soluble camptothecin.

Improving tumor delivery of lipophilic drugs through identifying advanced drug carrier systems with efficient carrier potency is of high importance. We have performed an investigative approach to identify parameters that affect liposomes' ability to effectively deliver lipophilic camptothecin (CPT) to target cells. CPT is a potent anticancer drug, but its undesired physiological properties are impairing its therapeutic use. In this study, we have identified parameters influencing incorporation and retention of lipophilic CPT in liposomes, evaluating the effect of lipid composition, lipid chemical structure (head and tail group variations, polymer inclusion), zeta potential and anisotropy. Polyethyleneglycol (PEG) surface decoration was included to avoid liposome fusing and increase the potential for prolonged in vivo circulation time. The in vitro effect of the different carrier formulations on cell cytotoxicity was compared and the effect of active targeting of one of the formulations was evaluated. We found that a combination of liposome surface charge, lipid headgroup and carbon chain unsaturation affect CPT incorporation. Retention in liposomes was highly dependent on the liposomal surroundings and liposome zeta potential. Inclusion of lipid tethered PEG provided stability and prevented liposome fusing. PEGylation negatively affected CPT incorporation while improving retention. In vitro cell culture testing demonstrated that all formulations increased CPT potency compared to free CPT, while cationic formulations proved significantly more toxic to cancer cells that healthy cells. Finally, antibody mediated targeting of one liposome formulation further enhanced the selectivity towards targeted cancer cells, rendering normal cells fully viable after 1 hour exposure to targeted liposomes.