Mid- to long-term periprosthetic bone density changes after cementless short stem hip arthroplasty in elderly: A clinical and radiological analysis.

Introduction: Short stem prostheses were originally designed for younger and more active patients. In recent years, they have been increasingly offered to older patients. This study evaluates the mid-to long-term survival of a short stem prosthesis and the changes in periprosthetic bone density following implantation of a cementless short hip stem in patients over 60 years of age. Methods: 118 patients aged over 60 received short stem prostheses. Clinical examination included Harris Hip Score (HHS) and Hip Disability and Osteoarthritis Outcome Score (HOOS). 93 patients were followed clinically for at least five years. 53 patients underwent dual-energy x-ray absorptiometry (DXA) and radiographic evaluation. Follow-up intervals were preoperative and postoperative (t0), at approximately six months (t1), at approximately two years (t2), and at approximately five years or later (t3). Results: Over a mean 6.7-year observation period for all 118 patients, one stem revision occurred due to a traumatic periprosthetic stem fracture. The five-year survival rate for the endpoint survival of the Metha® stem in 95 at-risk patients is 99.2%. HHS improved significantly from t0 55.3 ± 11.5 (range 30-79) to t3 95.3 ± 8.6 (range 57-100) at a mean of 8.0 years (p < 0.001). HOOS improved significantly in each subscale (p < 0.001). Bone mineral density (BMD) was available for review in 53 patients after a mean of 7.1 years. BMD increased from t0 to t3 in region of interest (ROI) 3 (+0.4%) and ROI 6 (+2.9%) and decreased in ROI 1 (-10.3%), ROI 2 (-9.8%), ROI 4 (-5.3%), ROI 5 (-3.4%) and ROI 7 (-23.1%). Conclusions: The evaluated short stem prosthesis shows a remarkably high survival rate in elderly patients, accompanied by excellent clinical results. Load transfer measurements show a metaphyseal-diaphyseal pattern with a trend towards increased diaphyseal transfer over the period observed.

[Implant anchorage: In vivo and in vitro analyses : Clusters for implant anchorage and safety]. / Implantatverankerung: In-vivo- und In-vitro-Analysen : Cluster Implantatverankerung und -sicherheit.

Aseptic implant loosening is the primary cause of revisions in arthroplasty. Various in vitro and in vivo methods are available for assessing implant fixation and stability. The aim of the Musculoskeletal Biomechanics Research Network (MSB-NET) is to continuously improve or develop these methods. In vitro analyses are often conducted using static and dynamic ISO and ASTM standards, while RSA, DXA, and EBRA analyses are established in vivo methods for evaluating implant fixation. Primary stability analyses, as well as acoustical methods, provide additional opportunities to detect loosening early and precisely evaluate implant stability. The cluster serves as a link between basic research, clinical practice, and end users to promote in vitro and in vivo methods to improve implant safety.

Development and Finite Element (FE) analysis of a novel short hip stem concept.

Introduction: In order to improve the anchorage behavior of short hip stems, this development project aims at designing a short hip stem concept that preserves the femoral neck and minimizes interference with the physiological stress distribution of the femur. The new design will be evaluated according to ISO 7206-4 which is the standard for testing Implants for surgery. Methods: Basic CAD models based on an established short stem prosthesis were created and evaluated using finite element analysis. The best design was further developed to achieve a more deformable stem while maintaining stability. The model was validated through in vitro testing. Results: The "H-Beam" short stem showed a higher degree of deformation of approximately 142-144% compared to the established short stem. The FE model had a relative error of 0.98% and 1.07% compared to the in vitro tests. An operating procedure was outlined for this new short stem design. Discussion: The FE model is deemed valid due to small differences in comparison to in vitro testing. The short-stem prosthesis is more flexible and can be easily adapted to individual anatomy during surgery. The prosthesis length is similar to conventional prostheses, but the new stem design could allow better and faster osteointegration while preserving the cancellous bone structure.

Acoustical determination of primary stability of femoral short stem during uncemented hip implantation.

BACKGROUND: Preparing the medullary space of the femur aims to create an ideal form-fitting of cementless implants to provide sufficient initial stability, which is crucial for osseous integration, ensuring good long-term results. Hammering the implant into the proximal femur creates a press-fit anchoring of the endoprosthesis in the medullary space. Implanting the optimal size of the shaft for best fitting should avoid damage to the bone. Modified acoustic signals in connection with implantation are being detected by surgeons and might be related to the primary stability of the implant. METHODS: This study aims to explore the relationship between frequency sound patterns and the change in stem stability. For this purpose, n = 32 Metha® short stems were implanted in a clinical setting by the same surgeon. During implantation, the sounds were recorded. To define a change in the acoustic system response during the operation, the individual blows of the implantation sequence were correlated with one another. FINDINGS: An algorithm was able to subdivide through sound analysis two groups of hammer blows (area 1 and area 2) since the characteristics of these groups showed significant differences within the frequency range of 100 Hz to 24 kHz. The edge between both groups, detected by the algorithm, was validated with expert surgeons' classifications of the same data. INTERPRETATION: In conclusion, monitoring, the hammer blows sound might allow quantification of the primary stability of the implant. Sound analysis including patient parameters and a classification algorithm could provide a precise characterization of implant stability.

Micromotion measurement at the interfaces of cemented tibial endoprosthetic replacements: A new standardized in vitro model using open-cell rigid foam.

Early aseptic loosening following primary total knee arthroplasty related to several factors might appear at the interface implant-cement or cement-bone. A standardized in vitro model might provide information on the relevance of single variable parameter of cementation including technique and cement respectively bone structure on fixation strength. Micromotion measurement using different directions of load should detect the primary stability of the interfaces. An open-cell rigid foam model was used for cementation of PFC-Sigma tibial trays with Palacos®. Pins were applied to the model for continuous non-destructive measurement. Relative micromotions for rotation, valgus-varus and extension flexion stress were detected at the interfaces as well as cement penetration was measured. The reproducibility of the measurement could be shown for all interfaces in extension-flexion movements. For rotation a negative trend was shown for the interface cement-prosthesis and cement-bone concerning varus-valgus stress reflecting varying surgical cementation technique. More micromotion related to extension-flexion force might reflect the design of the implant. Measurement of relative micromotion and cement distribution appear accurate to detect small differences of movement at different interfaces of cemented tibial implants and the results are reproducible for most parameter. An increased number of specimens should achieve statistical relevance for all measurements.

Retrospective clinical and X-ray-based outcome analysis of a short-stem hip arthroplasty taking into account the operative learning curve over 7 years in the 3-year control course.

INTRODUCTION: Self-monitoring is crucial to work progressively with a high-quality standard. A retrospective analysis is a valuable tool for studying the postoperative outcome of a prosthesis and for evaluating the learning process for the surgeon. MATERIALS AND METHODS: The learning process of one surgeon was analysed in 133 cases of hip arthroplasty. These were divided into seven groups representing the surgical years 2008-2014. Over the course of 3 postoperative years, a total of 655 radiographs were analysed at regarding three radiological quality parameters (centrum-collum-diaphyseal angle (CCD angle), intramedullary fit&fill ratio (FFR), and migration) and ancillary outcome parameters (Harris Hip Score (HHS), blood loss, operating time, and complications). This period was divided into five times: 1st-day post-op, 6 M, 12 M, 24 M, and 36 M. Bivariate Spearman's correlation analysis and pairwise comparisons were performed. RESULTS: The total collective achieved a proximal FFR of over 0.8. The distal prosthesis tip migrated and was located on the lateral cortex within the first months. The CCD angle initially showed a variation with a subsequent constant course. The HHS showed a significant increase (p < 0.001) to over 90 points postoperatively. Over time, the operating time and blood loss decreased. Intraoperative complications existed only at the beginning of the learning phase. A learning curve effect can be determined for almost all parameters by comparing the subject groups. CONCLUSIONS: Operative expertise was shown to gain through a learning curve, whereby postoperative results corresponded to the system philosophy of the short hip stem prosthesis. The distal FFR and the distal lateral distance could represent the principle of the prosthesis, which overall could be an interesting approach for verification of a new parameter.

Influence of muscle traction on the primary stability of a reverse humeral prosthesis.

Background: Currently, the influence of muscle traction on the postoperative stability of humeral prostheses is not adequately researched. This study analyzed the prosthesis' stability in vitro during muscle traction considering different bone defect sizes. Methods: The reverse humeral prosthesis "AEQUALIS™ ADJUSTABLE REVERSED" (Stryker) was implanted using press-fit into ten bones with a length of 200 mm and 160 mm. Subsequently, the models were torqued in 30 cycles using a universal testing machine (2 Nm - 6 Nm) and loaded axially to simulate muscle traction. The axial weight increased from 7.7 kg (pure muscle traction) over 40 kg (45-degree abduction) to 69.3 kg (90-degree abduction). The prosthesis' relative micromotion was simultaneously measured at three different measurement heights using high-sensitivity displacement transducers and compared to the relative micromotion without axial load. Results: It was found that a larger torsional moment was associated with a larger relative micromotion in both bone defects studied. However, the influence became significant (P < 0.014) in bone models with predominantly larger defect.Furthermore, no significant influence of muscle traction on relative micromotion could be detected for the larger bone models at any of the measurement levels (P = 1.000). In contrast, smaller bones showed no significant differences in muscle traction until a torsional moment of 6 Nm (P < 0.028). Conclusion: In conclusion, a larger torsional moment is associated with a higher relative micromotion and muscle traction, conclusively, has no effect on the primary stability of the reverse prosthesis for a 200 mm bone in vitro.

Development and validation of an algorithm to determine the minimal factors needed for non-invasive measurement of the in vivo primary stability of cementless hip implants.

Aseptic loosening is a frequent cause for revision of endoprosthesis. X-ray examinations like Radio-Stereometry-Analysis (RSA) are among the most widely used in vivo methods for its detection. Nevertheless, this method is not used routinely because of bone marker and related radiation exposure. This work aims at creating a new in vivo concept to detect implant stability measuring micromotions without x-ray and to develop a corresponding algorithm. Based on the assumption of contactless measurement, the input parameters for the algorithm are the distances of each ultrasound sensor to the object (prosthesis and bone) and its position. First, the number of parameters necessary for a precise reconstruction and measurement of micromotions between objects had to be defined. Therefore, the algorithm has been tested with simulations of these parameters. Two experimental measurements, either using contact sensors or ultrasound, were used to prove the accuracy of the algorithm. Simulations indicate a high accuracy with three distances as initial parameters for each object. Contact measurements show precise representation of micromotion, and the contactless measurements show the possibility of detecting various materials with a high resolution. This work lays the foundations for non-invasive detection of micromotions between the implant-bone interface.

Measuring Young's modulus of single trabeculae in cancellous bone using a two-point bending test.

BACKROUND: Surgical treatment of proximal humeral fractures poses a major challenge, especially in osteoporotic bone. At present, there appears to exist neither a suitable model for research to optimize the osteosynthesis processes nor are the structural data available which are required for developing such a model. Therefore, the aim of this study is to determine the microscopic morphology and Young's modulus of cancellous bone from human humeral heads considering osteoporotic changes. METHODS: Cylindrical samples were taken from ten fresh-frozen human humeral heads and structural analysis was done with µCT. Ten rod-like trabeculae were prepared from five of the humeral heads each which were measured and tested mechanically. For this purpose, the trabeculae were fixed on a slide and rotated axially under a stereo microscope. The sample cross-section and the depending moment of inertia were extracted from the image data. The samples were then loaded in a 2-point bending test and Young's moduli of the samples were determined. RESULTS: It could be shown that with increasing age of the donor, ossified portion of the cancellous bone decreased (p < 0.05). The average degree of mineralization of the bone was 1.24 (±0.06) g/mm3, which decreased with increasing age (p < 0.05). The determined Young's modulus averaged 1.33 (±1.76) GPa. INTERPRETATION: The verified structural parameter showed osteoporotic changes in the examined bone. This study for the first time determined Young's modulus of single trabeculae of cancellous bone of osteoporotically altered human humeral heads. Implementing the non-destructive sample measurement before exposure resulted in a methodical improvement.

Determination of E-modulus of cancellous bone derived from human humeri and validation of plotted single trabeculae: Development of a standardized humerus bone model.

Background: Evaluation of the mechanical behavior of the microstructure of cancellous bone seems important for the understanding of the mechanical behavior of bone. Prevention and treatment of fragility fractures due to osteoporosis is a major challenge according to ageing population. A bone model might help to assess fracture risk. Measurement of single trabeculae of bone should give further information compared with bone densitometry alone. This study measures the mechanical properties of single cancellous trabeculae derived from human proximal humerus. Methods: 34 single trabeculae dissected from human humeral heads were measured and evaluated mechanically. Trabeculae were fixed on microscope slides and geometrical data were reported during axial rotation of the specimens to measure the transverse section using computer aided design (CAD). The samples were subjected to a two-point bending test and were loaded with a measure-stamp at a defined distance. Force and deflection were measured by high-resolution sensors. The E-modulus was then calculated in combination with finite elements method simulation (FEM), using the previously obtained CAD-Data. Results: The average E-modulus from 34 valid measurements of human humeral trabeculae was 1678 MPa with a range from 829 to 3396 MPa, which is consistent with existing literature. The planned additional validation of the measurement method using manufactured three-dimensional synthetic trabeculae with known mechanical properties showed an average elastic modulus of single trabeculae of 51.5 MPa, being two dimensions lower than the value reported in the datasheet of the plastic. Conclusion: This newly developed, time and cost-efficient procedure allows the measurement of E-modulus in single trabeculae. Measurement of mechanic parameters of single trabeculae might give insights on mechanic behavior of bone and be relevant for the research of systemic bone diseases, complementing the existing data on bone-mineral-density. Further examination of single trabeculae of human cancellous bone should give an insight on the mechanical behavior of bone also considering systemic bone diseases.

Press-fit reverse shoulder arthroplasty in case of advanced humeral bone loss - Is additional distal fixation necessary for primary stability?

BACKGROUND: Revision reverse shoulder arthroplasty (RSA) poses considerable surgical challenges. We hypothesized that a newly developed press-fit stem, which is modeled on the medullary canal of the supracondylar region of the distal humerus by a slight distal bend, achieve both correct fit and sufficient primary stability and that additional distal fixation by interlocking screws is favorable in case of advanced humeral bone loss. METHODS: A modular tapered press-fit stem was implanted in 16 Sawbone humeri in three consecutively created defect situations (200 mm (experimental group type 3°), 160 mm (type 4°) and 120 mm (type 5°) bone length above the epicondylar line. In experimental groups type 4° and 5°, additional distal interlocking screw fixation with one to three screws was tested. Primary stability was investigated by measuring micromotions with a high-precision rotational setup. FINDINGS: Highest relative micromotions were noted at the proximal end in experimental groups type 3° and type 4°, whereas in type 5° highest micromotions could be seen at the distal end. Overall micromotions were significantly lower in type 3° and increased with extended defect size. In experimental group type 5°, micromotions increased with reduced additional distal screw fixation. INTERPRETATION: The examined press-fit stem did not provide sufficient primary rotational stability in all constructs without additional support. Advanced distal humeral bone loss had a strong impact on primary fixation. In experimental group type 5° with 120 mm bone remaining, it might be beneficial to use three distal interlocking screws in the supracondylar region in order to neutralize torque and to avoid early loosening.

How do the geometries of the broach handles relate to the distribution of force and moments in a femoral model?

The continuous improvement of minimally invasive hip endoprostheses surgery comes with a change in geometries of surgery instruments like the broach handles. Consequently, depending on the handles' curvature this results in a deviation between handle and femoral axis. Therefore, this study aimed to prove the influence of different handles' curvatures on the preparation of implant site and acting forces and moments in this process. Five femoral models attached to different handles (double-curved, single-curved, straight) were locked in a drop-weight device with standardize implantation forces and moments and five strokes were measured for each possible combination. Distribution of force and moment components was dependent on the handle's curvature, where the lowest variation from the standard force values was by the straight one (av:15.2% ± 0.5%) and the strongest discrepancies were exhibit by the double-curved one (av:54.3% ± 0.1%.). Moment values have also shown this trend with the lowest variation (12.4%-23.3%) by the straight one and the highest discrepancies (56,6%-90.9%) by the double-curved one. Results show that unguided axial impact introduces unwanted transverse forces and moments into the femur. Therefore, broach handles should be modified accordingly so that minimally invasive surgery remains feasible but unwanted forces or moments can still be compensated.

Comparison of Short Stems Versus Straight Hip Stems: A Biomechanical Analysis of the Primary Torsional Stability.

Cementless straight stems show very good survival rates. However, the more distal force application of straight stems may lead to release-related proximal stress-shielding. Nevertheless, this technical brief had the objective of conducting a biomechanical in vitro analysis comparing short stems with established straight stems with respect to their primary torsional stability. Two cementless short hip stems and three cementless straight hip stems were implanted in n = 5 synthetic femora each. Torsional torques were applied into the hip stems at a continuous interval of ±7 Nm. Micromotions were measured by six inductive extensometers on four different measurement levels. At the proximal measuring point, significantly smaller relative micromotions of the CLS® prosthesis could be detected compared to all other stem models (p < 0.05). In all stem models, smallest relative micromotions were found at the metaphyseal/diaphyseal measuring point. Only at the measuring point of the distal tips of the straight stems, statistically significantly lower relative micromotion of the CLS® stem compared to the Trendhip® stem could be found (p < 0.01). All the investigated stems generally display a rather comparable anchoring pattern and an almost physiological force application. Since the comparatively long straight stems present an anchoring pattern nearly identical to that of the examined short stems, a shortening of the established straight stems could be taken into consideration. This would offer the advantage of minimally invasive surgery and bone-saving resection as well as preservation of cancellous bone in case a revision would become necessary.

How screw connections influence the primary stability of acetabular cups under consideration of different bone models.

INTRODUCTION: Good osteointegration of implants requires sufficient primary stability. Aim of this study was to examine the influence of screw fixation on the primary stability of press-fit cups. METHODS: Two press-fit acetabular cups were tested with regard to the influence and number of screws and their primary stability. RESULTS: For the relatively thin-walled Allofit®-S cup, an influence of the number of screws on the different forms of movement could be demonstrated. CONCLUSIONS: We see a clear influence of the cup wall thickness on the elastic deformability and accordingly on the primary stability of the examined cups.

Influence of thermodisinfection on microstructure of human femoral heads: duration of heat exposition and compressive strength.

Allogeneic bone derived from living donors being necessary to match demand for bone transplantation and thermodisinfection of femoral heads is an established sterilization method. During the thermodisinfection the peripheral bone is exposed to maximum 86 °C for 94 min providing 82.5 °C within the center of the femoral head for at least 15 min. This study examined the compression force of the central and representative peripheral regions of native and thermodisinfected human femoral heads to observe wether different duration and intensity of heat exposure might alter mechanic behaviour. Slices from the equatorial region of human femoral heads were taken from each 14 native and thermodisinfected human femoral heads. The central area revealed a significantly higher compression force for native (p ≤ 0.001) and for thermodisinfected bone (p = 0.002 and p = 0.005) compared with peripheral regions since no relevant differences were found between the peripheral and intermediate areas themselves. A small reduction of compression force for thermodisinfected bone was shown since this did not appear significant due to the small number of specimens. The heat exposure did not alter the pre-existing anatomical changes of the microarchitecture of the native femoral heads from the center towards the peripheral regions. The heterogeneity of microstructure of the femoral head might be of interest concerning clinical applications of bone grafts since the difference between native and thermodisinfected bone appears moderate as shown previously. The different quantity of heat exposure did not reveal any significant influence on compression force which might enable thermodisinfection of preformed bone pieces for surgical indications.

Outcome of short- to medium-term migration analysis of a cementless short stem total hip arthroplasty using EBRA-FCA: a radiological and clinical study.

INTRODUCTION: Stress shielding may lead to aseptic loosening which is a common reason for implant failure. An established method to identify implants with risk of implant failure caused by aseptic loosening is to measure early migration of the stem with the "Ein Bild Roentgen Analyse" femoral component analysis (EBRA-FCA). Therefore, the aim of this study was to measure the migration of a cementless short stem prosthesis via EBRA-FCA to predict the future performance. MATERIALS AND METHODS: A total collective of 71 patients were treated with a cementless short hip stem prosthesis. Indications for surgery were primary coxarthrosis, dysplasia coxarthrosis or femoral head necrosis. After surgery, the patients were followed-up immediately after 3, 6, 12, 24, 36, and 48 months and X-ray images for EBRA-FCA measurements were taken. Axial caudal migration as well as the varus/valgus tilting of the prosthesis was determined. Possible influencing factors like BMI, age, diagnosis, gender or Harris Hip Score (HHS) on the migration of the stem were assessed. RESULTS: HHS increased significantly direct postoperatively (p < 0.001). At the second follow-up the average caudal migration was 0.42 ± 0.52 mm (range: 0.00-2.85 mm) (p < 0.001). A total of 14 patients underwent a caudal migration greater than 1.5 mm until 48 months. The initial varus and valgus tilts within the first 3 months were significant (p < 0.001). No correlations between BMI, age, diagnosis, gender or HHS and the migration as well as the tilting of the cementless short hip stem prosthesis were found. CONCLUSIONS: Although initial axial caudal migration as well as tilting tendencies in varus or valgus position can be detected, there is no marked migration of the examined prosthesis after the first 48 months. Likewise, no aseptic early loosening was detected throughout the study period, which indicates good osseointegration of the short stem prosthesis.

Biomechanical testing of various suture techniques for Achilles tendon repair with and without augmentation by using synthetic polyester grafts.

Following surgical Achilles tendon reconstruction surgery, there is a distinct trend towards an early and faster rehabilitation protocol to avoid muscle atrophy. However, this procedure involves the risk of a higher complication rate. In order to reduce the occurrence of re-ruptures and pathological tendon extensions, a tendon reconstruction with the highest possible primary stability is desirable. Therefore, the aim of this study was to determine if augmentation using synthetic polyester tapes (QuadsTape™) could provide greater primary stability in case of different tendon suture techniques. 90 tendons of the superficial toe flexor of pigs were divided into 9 groups. The reconstruction method was combined using the factors suture technique (Kessler and Bunnell), augmentation (non-augmented and augmented with QuadsTape™) and defect type (end-to-end and 10 mm gap). The biomechanical measurements were performed on a material testing machine and consisted of a creep test, a cyclic test and a tear-off test. This study compared creep strain, ultimate load failure, maximum stress and stiffness. Irrespective of the type of defect involved, augmentation of the tendon sutures led to a significant increase of the maximum force (not augmented: 82.30 ±â€¯25.48 N, augmented: 135.73 ±â€¯30.69 N, p < 0.001) and the maximum stress (not augmented: 2.26 ±â€¯0.83 MPa, augmented: 4.13 ±â€¯1.79 MPa, p < 0.001). Furthermore, there was a non-significant increase in stiffness and no significant differences were observed with respect to creep strain. Augmentation of Achilles tendon reconstruction using QuadsTape™ increases composite strength and stiffness in the in vitro model, thus potentially contributing to the feasibility of early rehabilitation programs. Biological factors still need to be investigated in order to formulate appropriate indications.

In vitro examination of the primary stability of three press-fit acetabular cups under consideration of two different bearing couples.

BACKROUND: For preclinical statements about the anchoring behavior of prostheses, the primary stability of the prosthesis is of special importance. It was the aim of this study to examine and compare the relevant relative micromotions of three different acetabulum prostheses by introducing three-dimensional torques. METHODS: The cups were implanted under standard conditions into an anatomical artificial bone model. Three-dimensional torques were applied to the acetabular cups. Taking into account the resulting frictional moments of two different bearing couples, ceramic-on-ceramic and ceramic-on-polyethylene, the relative micromotions of the cups were recorded as maximum total micromotion, translational and rotational micromotion, and the primary stability values of the three cups were compared. RESULTS: Relative micromotion of all cup models was always significantly smaller with the CoC bearing couples than with the CoP bearing couples (p < 0.001). The rotational micromotion was always lower (p < 0.001) than the translational micromotion, and the rotational as well as the translational micromotions were each always lower than the maximum total micromotion (p < 0.001, p < 0.010). The thinnest-walled cup system always showed the largest relative micromotions. CONCLUSION: The results of our study can be interpreted as indicating that the low relative micromotions of all cups - irrespective of the use of CoC or CoP bearing couples - are within an acceptable range favoring secondary osseointegration of the implants. Furthermore, we were able to show that the cup wall thickness and the surface quality of the cup systems have an influence on the primary stability and the elastic deformability of the examined cup systems.

Development of periprosthetic bone mass density around the cementless Metha® short hip stem during three year follow up-a prospective radiological and clinical study.

PURPOSE: The purpose of this study was to check the concept of the cementless Metha® short hip stem in order to find out whether proximal physiological load transfer can be achieved. METHODS: Fourty-three patients were included. Epidemiological factors were established. The Harris Hip Score was determined and measurement of bone mass density as well as osteodensitometric and radiological measurements was carried out pre-operatively, post-operatively, and after six, 12, 24, and 36 months. RESULTS: Harris Hip Score improved from 55.9 ± 12.4 pre-operatively to 94.8 ± 8.2 after 36 months (p < 0.001). After initial reduction of bone density in zones 1 and 7 up to six months post-operatively, there was a steady approximation of bone density to the initial values (p < 0.05). CONCLUSION: The Metha® short hip stem shows good clinical results. Furthermore, there is an increase of bone density in the proximal zones 1 and 7 between six and 36 months serving as a sign of physiological load transfer.

Age-related osseointegration of a short hip stem: a clinical and radiological 24 months follow-up.

PURPOSE: The purpose of this study was to examine potential differences between patients under and over 60 years who underwent a total short hip stem arthroplasty in a 24-month follow-up in a clinical setting. METHODS: Sixty seven patients were included in this prospective study and divided in two groups. In the younger cohort 39 patients ≤ 59 years and in the older cohort 28 patients ≥ 60 years were included. Clinical and radiological examinations of the patients took place preoperatively, postoperatively and after 3, 6, 12 and 24 months. The Harris Hip Score (HHS) was raised as clinical examination. Changes of bone mass density (BMD), stress shielding, reactive lines, spot welds and sclerosing were examined as radiological analysis. RESULTS: The HHS improved from 53.6 ± 8.2 preoperative to 93.2 ± 9.6 in the younger cohort and for the older cohort from 57.6 ± 14.8 to 94.1 ± 7.6 after 24 months. BMD growth was detectable in regions of interest (ROI) 3 and 6 for both groups. Different results between the cohorts could only be detected in ROIs 4 and 5. The older cohort showed a loss of BMD of 5.95% in ROI 4 and 3.17% in ROI 5 after 24 months, whereas the younger cohort showed no loss of BMD in both ROIs. CONCLUSIONS: No significant differences or any influences of osseointegration and clinical outcome of the short hip stem for both groups were detectable. Lower losses (ROIs 1 and 2) and higher growths (ROIs 3, 4, 5) were discovered in younger patients and the HHS improved in both groups. Reasons for this result could be age, sex or the level of activity of the patients, but in both groups the short hip stem shows comparable results in clinical as well as in radiological examination. We conclude that the short hip stem seems to be an adequate treatment also for older patients.