Design, evaluation and optimization of taste masked clarithromycin powder.

Clarithromycin (CLA) is an extremely bitter macrolide antibiotic used to treat paediatric and adult infections. The bitter taste affects patient adherence and may compromise therapy. This research developed a taste masked CLA resinate using Indion® 234, a weak acidic cation exchange resin. The factors affecting formation of the CLA-resin complex were assessed. Design of experiments was used to optimize response while evaluating input variables such as temperature, CLA-resin ratio,stirring time and pH. CLA loading efficiency was determined spectrophotometrically and CLA release using USP Apparatus II. Differential Scanning Calorimetry (DSC), Scanning Electron Microscop (SEM), Fourier Transform Infrared (FT-IR) Spectroscopy and X-ray Diffraction (XRD) were used to confirm complex formation. A spectrophotometric method was used to assess taste evaluation. The optimum CLA-resin ratio, temperature, and stirring time were 1:4, 80 °C, 3 hours, respectively, at pH 8. Characterization techniques revealed that CLA was crystalline and the complex amorphous in nature. FT-IR spectra of resinate revealed the absence of resonance due to the tertiary amine functional group that is responsible for the bitter taste of CLA. CLA was stable in simulated salivary fluid and was released within 3 hours in gastric fluid. All CLAresin batches revealed complete taste masking. Taste analysis highlighted the improvement of taste masking properties of the resinate as the CLA to resin ratio, increased.

The use of experimental design for the development and validation of an HPLC-ECD method for the quantitation of efavirenz.

A high performance liquid chromatography with electrochemical detection (HPLC-ECD) method for the quantitation of efavirenz (EFV) was developed, since traditional HPLC-UV methods may be inappropriate, given that EFV undergoes photolytic degradation following exposure to UV light. This work describes the use of response surface methodology (RSM) based on a central composite design (CCD) to develop a stability-indicating HPLC method with pulsed ECD in direct current (DC) mode at an applied potential difference and current of +1400 mV and 1.0 µA for the analysis of EFV. Separation of EFV and imipramine was achieved using a Nova-Pak®C18 cartridge column and a mobile phase of phosphate buffer (pH 4.5): acetonitrile (ACN) (55:45 v/v). Mobile phase pH, buffer molarity, ACN concentration and applied potential difference were investigated. The optimized method produced sharp well resolved peaks for imipramine and EFV with retention times of 3.70 and 8.89 minutes. The calibration curve was linear (R2 = 0.9979) over the range 5-70 µg/mL. Repeatability and intermediate precision ranged between 3.37 and 4.34 % RSD and 1.31 and 4.29 % RSD and accuracy between -0.80 and 4.71 % bias. The LOQ and LOD were 5.0 and 1.5 µg/mL. The method was specific for EFV and was used to analyse EFV in commercially available tablets. The HPLC-ECD method is more suitable for quantitative analysis of EFV than HPLC-UV.

The use of experimental design for the development of a capillary zone electrophoresis method for the quantitation of captopril.

A capillary zone electrophoresis (CZE) method for the quantitation of captopril (CPT) using UV detection was developed. Influence of electrolyte concentration and system variables on electrophoretic separation was evaluated and a central composite design (CCD) was used to optimize the method. Variables investigated were pH, molarity, applied voltage and capillary length. The influence of sodium metabisulphite on the stability of test solutions was also investigated. The use of sodium metabisulphite prevented degradation of CPT over 24 hours. A fused uncoated silica capillary of 67.5cm total and 57.5 cm effective length was used for analysis. The applied voltage and capillary length affected the migration time of CPT significantly. A 20 mM phosphate buffer adjusted to pH 7.0 was used as running buffer and an applied voltage of 23.90 kV was suitable to effect a separation. The optimized electrophoretic conditions produced sharp, well-resolved peaks for CPT and sodium metabisulphite. Linear regression analysis of the response for CPT standards revealed the method was linear (R2 = 0.9995) over the range 5-70 µg/mL. The limits of quantitation and detection were 5 and 1.5 µg/mL. A simple, rapid and reliable CZE method has been developed and successfully applied to the analysis of commercially available CPT products.