Extraction of silica from sugarcane bagasse ash and its utilization in zeolite 4A synthesis for CO2 adsorption.

Sugarcane bagasse ash (SCBA) is a solid waste containing a high amount of silica (SiO2) and is suitable to utilize as a silica source for synthesizing zeolite NaA. SCBA is typically calcined at high temperatures before silica extraction. The method is not environmentally friendly because it consumes energy and produces CO2. This work demonstrates an alternative extraction method of SiO2 from SCBA by treating it with hydrochloric (HCl) and sodium hydroxide (NaOH) solution. The obtained mixture was separated by paper filter No. 1 (P) and a combination of paper filter and syringe filter (PS). The solution was neutralized by HCl solution, producing silica (SiO2-P and SiO2-PS) with a purity of 98 wt%. Both SiO2 samples and SCBA were utilized to synthesize zeolite NaA for CO2 adsorption. The CO2 adsorption capacities of NaA-P and NaA-PS were 4.30 and 4.10 mmol gadsorbent -1, in the same range as commercial NaA. The capacity is influenced by the total basicity of zeolite. The CO2 adsorption behavior of all samples correlates well with the Toth model. The CO2 adsorption kinetics agrees well with the pseudo-second-order kinetic model. Overall, this work shows the successful extraction of silica via using a direct NaOH solution, yielding high-purity silica sufficient for synthesizing zeolite NaA, a promising adsorbent of CO2.

General Pyrolysis for High-Loading Transition Metal Single Atoms on 2D-Nitro-Oxygeneous Carbon as Efficient ORR Electrocatalysts.

Single-atom catalysts (SACs) possess the potential to involve the merits of both homogeneous and heterogeneous catalysts altogether and thus have gained considerable attention. However, the large-scale synthesis of SACs with rich isolate-metal sites by simple and low-cost strategies has remained challenging. In this work, we report a facile one-step pyrolysis that automatically produces SACs with high metal loading (5.2-15.9 wt %) supported on two-dimensional nitro-oxygenated carbon (M1-2D-NOC) without using any solvents and sacrificial templates. The method is also generic to various transition metals and can be scaled up to several grams based on the capacity of the containers and furnaces. The high density of active sites with N/O coordination geometry endows them with impressive catalytic activities and stability, as demonstrated in the oxygen reduction reaction (ORR). For example, Fe1-2D-NOC exhibits an onset potential of 0.985 V vs RHE, a half-wave potential of 0.826 V, and a Tafel slope of -40.860 mV/dec. Combining the theoretical and experimental studies, the high ORR activity could be attributed its unique FeO-N3O structure, which facilitates effective charge transfer between the surface and the intermediates along the reaction, and uniform dispersion of this active site on thin 2D nanocarbon supports that maximize the exposure to the reactants.

Unraveling Structural and Acidic Properties of Al-SBA-15-supported Metal Phosphates: Assessment for Glucose Dehydration.

5-Hydroxymethylfurfural (5-HMF) synthesized through glucose conversion requires Lewis acid (L) site for isomerization and Brønsted acid (B) site for dehydration. The objective of this work is to investigate the influence of the metal type of Al-SBA-15-supported phosphates of Cr, Zr, Nb, Sr, and Sn on glucose conversion to 5-HMF in a NaCl-H2 O/n-butanol biphasic solvent system. The structural and acid property of all supported metal phosphate samples were fully verified by several spectroscopic methods. Among those catalysts, CrPO/Al-SBA-15 provided the best performance with the highest glucose conversion and 5-HMF yield, corresponding to the highest total acidity of 0.65 mmol/g and optimal L/B ratio of 1.88. For CrPO/Al-SBA-15, another critical parameter is the phosphate-to-chromium ratio. Moreover, DFT simulation of glucose conversion to 5-HMF on the surface of the optimized chromium phosphate structure reveals three steps of fructose dehydration on the Brønsted acid site. Finally, the optimum reaction condition, reusability, and leaching test of the best catalyst were determined. CrPO/Al-SBA-15 is a promising catalyst for glucose conversion to high-value-added chemicals in future biorefinery production.

Nanostructured N/S doped carbon dots/mesoporous silica nanoparticles and PVA composite hydrogel fabrication for anti-microbial and anti-biofilm application.

Regarding the convergence of the worldwide epidemic, the appearance of bacterial infection has occasioned in a melodramatic upsurge in bacterial pathogens with confrontation against one or numerous antibiotics. The implementation of engineered nanostructured particles as a delivery vehicle for antimicrobial agent is one promising approach that could theoretically battle the setbacks mentioned. Among all nanoparticles, silica nanoparticles have been found to provide functional features that are advantageous for combatting bacterial contagion. Apart from that, carbon dots, a zero-dimension nanomaterial, have recently exhibited their photo-responsive property to generate reactive oxygen species facilitating to enhance microorganism suppression and inactivation ability. In this study, potentials of core/shell mesoporous silica nanostructures (MSN) in conjugation with carbon dots (CDs) toward antimicrobial activity against Staphylococcus aureus, Pseudomonas aeruginosa and Escherichia coli have been investigated. Nitrogen and sulfur doped CDs (NS/CDs) conjugated with MSN which were cost effective nanoparticles exhibited much superior antimicrobial activity for 4 times as much as silver nanoparticles against all bacteria tested. Among all nanoparticles tested, 0.40 M NS/CDs@MSN showed the greatest minimal biofilm inhibitory at very low concentration (< 0.125 mg mL-1), followed by 0.20 M NS/CDs@MSN (0.5 mg mL-1), CD@MSN (25 mg mL-1), and MSN (50 mg mL-1), respectively. Immobilization of NS/CDs@MSN in polyvinyl alcohol (PVA) hydrogel was performed and its effect on antimicrobial activity, biofilm controlling efficiency, and cytotoxicity toward fibroblast (NIH/3 T3 and L-929) cells was additionally studied for further biomedical applications. The results demonstrated that 0.40 M NS/CDs-MSN@PVA hydrogel exhibited the highest inhibitory effect on S. aureus > P. aeruginosa > E. coli. In addition, MTT assay revealed some degree of toxicity of 0.40 M NS/CDs-MSN@PVA hydrogel against L-929 cells by a slight reduction of cell viability from 100% to 81.6% when incubated in the extract from 0.40 M NS/CDs-MSN@PVA hydrogel, while no toxicity of the same hydrogel extract was detected toward NIH/3 T3 cells.

Unraveling the Adsorption Behavior of Thymol on Carbon and Silica Nanospheres for Prolonged Antibacterial Activity: Experimental and DFT Studies.

Functionalization of thymol (Thy) on nanocarriers is a key step in achieving prolonged antimicrobial activity. This requires nanomaterials with uniform particle diameters and suitable thymol sorption. Herein, hollow carbon (HC) and SiO2-carbon core-shell (SiO2@C) were investigated due to their diverse morphologies and ease of surface modification. HC (14 ± 1 nm size) and SiO2@C (10 ± 1.5 nm size) were synthesized by the Stöber method before thymol was loaded by incipient wetness impregnation. Nanoparticle physicochemical properties were characterized by advanced techniques, including X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine structure (NEXAFS). Adsorption energies of thymol on the carbon and SiO2 surfaces were elucidated by density functional theory (DFT) simulations. Moreover, the in vitro thymol release profiles and antibacterial activity were evaluated. The experimental results indicated that the oxy-carbon surface species of HC led to longer thymol release profiles than the -OH group of SiO2@C. The DFT calculations revealed that the weaker physical interaction of thymol on HC was better for drug release than that on SiO2@C. Thus, a longer thymol release profile of HC with hollow structures showed better antibacterial performance against Gram-positive bacteria Staphylococcus aureus than that of SiO2@C with core-shell structures. This work confirms the important role of carbon morphology and specific functional groups in thymol release profiles for the further development of inhibition products.

Structural Evolution of Iron-Loaded Metal-Organic Framework Catalysts for Continuous Gas-Phase Oxidation of Methane to Methanol.

Catalytic partial oxidation of methane presents a promising route to convert the abundant but environmentally undesired methane gas to liquid methanol with applications as an energy carrier and a platform chemical. However, an outstanding challenge for this process remains in developing a catalyst that can oxidize methane selectively to methanol with good activity under continuous flow conditions in the gas phase using O2 as an oxidant. Here, we report a Fe catalyst supported by a metal-organic framework (MOF), Fe/UiO-66, for the selective and on-stream partial oxidation of methane to methanol. Kinetic studies indicate the continuous production of methanol at a superior reaction rate of 5.9 × 10-2 µmolMeOH gFe-1 s-1 at 180 °C and high selectivity toward methanol, with the catalytic turnover verified by transient methane isotopic measurements. Through an array of spectroscopic characterizations, electron-deficient Fe species rendered by the MOF support is identified as the probable active site for the reaction.

Cryo-Induced Cellulose-Based Nanogel from Elaeis guineensis for Antibiotic Delivery Platform.

Cryo-induced hydrogel from cellulose is a new class of biomaterials for drug delivery, cell delivery, bone and skin tissue engineering for cell proliferation and regeneration applications. This research aimed to synthesize cryo-induced hydrogel from cellulose and carboxymethyl cellulose (CMC) produced from empty bunch's cell wall of Elaeis guineensis. First, the experiment was to produce cellulose-rich material using hot-compressed water extraction followed by alkaline delignification and bleaching with H2O2. The obtained bleached EFB cellulose was used as the substrate for CMC, and the optimal condition with the highest degree of carboxyl substitution (DS) of 0.75 was achieved when varying NaOH and monochloroacetic acid concentration as well as etherification temperature using fractional factorial design. For cryogelation study, hydrogels were synthesized from cellulose, CMC and beta-cyclodextrin (ß-CD) by dissolving cellulose-based matrix in a NaOH/urea system, and the cellulose (CEL) solution was frozen spontaneously at -40 °C followed by high speed mixing to loosen cellulose fibrils. Epichlorohydrin (ECH) and Polyethylene glycol diglycidyl ether (PEGDE) were used as a cross-linker. First, the ratio of cellulose and CMC with different amounts of ECH was investigated, and subsequently the proper ratio was further studied by adding different crosslinkers and matrices, i.e., CMC and ß-CD. From the result, the ECH crosslinked CMC-CEL (E-CMC-CEL) gel had the highest swelling properties of 5105% with the average pore size of lyophilized hydrogel of 300 µm. In addition, E-CMC-CEL gel had the highest loading and release capability of tetracycline in buffer solution at pH 7.4 and 3.2. At pH 7.4, tetracycline loading and release properties of E-CMC-CEL gel were 65.85 mg g-1 dry hydrogel and 46.48 mg g-1 dry hydrogel (70.6% cumulative release), respectively. However, at pH 3.2, the loading and release capabilities of Tetracycline were moderately lower at 16.25 mg g-1 dry hydrogel and 5.06 mg g-1 dry hydrogel, respectively. The findings presented that E-CMC-CEL hydrogel was a suitable material for antibiotic tetracycline drug carrying platform providing successful inhibitory effect on Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa, respectively.

Insight into the photocatalytic reduction of hexavalent chromium using photodeposited metal nanoparticle-TiO2 photocatalysis.

Hexavalent chromium (Cr(VI)) is carcinogenic to organisms. It is widely used in several industries. In this work, we investigated the Cr(VI) photocatalytic reaction with a scavenger on Pt and Cu-TiO2 photocatalysts. Metal-deposited TiO2 was successfully synthesized by a photodeposition method. TEM-EDX, XRD, and UV-DR were analyzed to study the changes in morphology, crystallinity, and the electronic properties of photocatalysts. The rate of charge recombination during reduction and photoluminescence (PL) spectroscopy was used to examine the catalysts in depth. Cu-TiO2 demonstrates the highest photocatalytic activity for 63.74% of Cr(VI) removal. To understand the photoreduction of Cr(VI), the fate transformation of Cr species during the adsorption and reaction was investigated using in situ XANES. The results demonstrated that the Cr(III) was noticeably main component adsorbed over the catalyst, particularly in Cu-TiO2. The presence of humic acid can boost the Cr(VI) removal efficiency and enhanced the Cr(VI) reduction to Cr(III). We believe that the extensive research on Cr(VI) photoreduction on metal-TiO2 heterojunction will provide a comprehensive understanding of catalytic behaviors, paving the way for rationally designed novel Cr reduction catalysts.

New Folding 2D-Layered Nitro-Oxygenated Carbon Containing Ultra High-Loading Copper Single Atoms.

The discoveries of 2D nanomaterials have made huge impacts on the scientific community. Their unique properties unlock new technologies and bring significant advances to diverse applications. Herein, an unprecedented 2D-stacked material consisting of copper (Cu) on nitro-oxygenated carbon is disclosed. Unlike any known 2D stacked structures that are usually constructed by stacking of separate 2D layers, this material forms a continuously folded 2D-stacked structure. Interestingly, advanced characterizations indicate that Cu atoms inside the structure are in an atomically-dispersed form with extraordinarily high Cu loading up to 15.9 ± 1.2 wt.%, which is among the highest reported metal loading for single-atom catalysts on 2D supports. Facile exfoliation results in thin 2D nanosheets that maximize the exposure of the unique active sites (two neighboring Cu single atoms), leading to impressive catalytic performance, as demonstrated in the electrochemical oxygen reduction reaction.

Platinum/carbon dots nanocomposites from palm bunch hydrothermal synthesis as highly efficient peroxidase mimics for ultra-low H2O2 sensing platform through dual mode of colorimetric and fluorescent detection.

Detection of hydrogen peroxide and glucose in nanomolar level is crucial for point-of-care medical diagnosis. It has been reported that human's central nervous system diseases such as Alzheimer's disease, Parkinson's disease, and even amyotrophic lateral sclerosis, are presumably caused H2O2 or reactive radical species (ROS). Sensing of H2O2 released from human biofluids, tissues, organ from metabolism disorder at ultra-low concentration assists for early identification of severe diabetis mellitus related to glucose, and heart attack, as well as stroke related to cholesterol. In this work, carbon dots (CDs) having an average diameter at 6.99 nm with highly photoluminescence performance were successfully synthesized from palm empty fruit bunch (EFB) using green and environmentally friendly process via hydrothermal condition. CDs acted well on peroxidase-like activity for H2O2 detection at room temperature, however their sensitivity on ultra-low H2O2 concentration needed to be improved. To enhance their reactivity on H2O2 nanozyme activity at room temperature, synthesis of hybrid metal nanoparticles (AgNPs and PtNPs) on CDs surface was established. The findings exhibited that CDs/PtNPs was the most suitable nanozyme achieving highly efficient peroxidase mimic for dual mode of colorimetric and fluorescent H2O2 sensing platform at very low limit of detection of 0.01 mM (10 nM) H2O2.

Correlating the effect of preparation methods on the structural and magnetic properties, and reducibility of CuFe2O4 catalysts.

CuFe2O4 spinel oxide has attracted research interest because of its versatile practical applications, especially for catalysis. In this study, nanometre-sized CuFe2O4 particles were prepared by three different methods, including nanospace confinement in SBA-15, hard template removal, and sol-gel combustion. The relationship between structure, size, magnetic behaviour, and reducibility of the catalysts was further investigated by various advanced techniques. Samples prepared by impregnation and hard template removal show high surface area and small crystallite size with superparamagnetic behaviour. In contrast, the sol-gel sample exhibits ferromagnetic properties with a large crystallite size and low surface area. Although all samples present a tetragonal crystal structure, the distributions of Fe and Cu cations in tetrahedral and octahedral sites in the spinel structure are different. The reducibility results demonstrate that the supported CuFe2O4/SBA-15 shows the lowest reduction profile. These results could suggest that the synthesis method strongly affects the crystal properties and cation distribution in the spinel structure, microstructure, surface area and reducibility, which are among the most relevant physicochemical properties for the catalytic activity.

The Role of N and S Doping on Photoluminescent Characteristics of Carbon Dots from Palm Bunches for Fluorimetric Sensing of Fe3+ Ion.

This work aims to enhance the value of palm empty fruit bunches (EFBs), an abundant residue from the palm oil industry, as a precursor for the synthesis of luminescent carbon dots (CDs). The mechanism of fIuorimetric sensing using carbon dots for either enhancing or quenching photoluminescence properties when binding with analytes is useful for the detection of ultra-low amounts of analytes. This study revealed that EFB-derived CDs via hydrothermal synthesis exceptionally exhibited luminescence properties. In addition, surface modification for specific binding to a target molecule substantially augmented their PL characteristics. Among the different nitrogen and sulfur (N and S) doping agents used, including urea (U), sulfate (S), p-phenylenediamine (P), and sodium thiosulfate (TS), the results showed that PTS-CDs from the co-doping of p-phenylenediamine and sodium thiosulfate exhibited the highest PL properties. From this study on the fluorimetric sensing of several metal ions, PTS-CDs could effectively detect Fe3+ with the highest selectivity by fluorescence quenching to 79.1% at a limit of detection (LOD) of 0.1 µmol L-1. The PL quenching of PTS-CDs was linearly correlated with the wide range of Fe3+ concentration, ranging from 5 to 400 µmol L-1 (R2 = 0.9933).

Effect of Co-Doping on Cu/CaO Catalysts for Selective Furfural Hydrogenation into Furfuryl Alcohol.

Cu/CaO catalysts with fine-tuned Co-doping for excellent catalytic performance of furfural (FAL) hydrogenation to furfuryl alcohol (FOL) were synthesized by a facile wetness impregnation method. The optimal Co1.40Cu1/CaO catalyst, with a Co to Cu mole ratio of 1.40:1, exhibited a 100% FAL conversion with a FOL yield of 98.9% at 100 °C and 20 bar H2 pressure after 4 h. As gained from catalyst characterizations, Co addition could facilitate the reducibility of the CoCu system. Metallic Cu, Co-Cu alloys, and oxide species with CaO, acting as the major active components for the reaction, were formed after reduction at 500 °C. Additionally, this combination of Co and Cu elements could result in an improvement of catalyst textures when compared with the bare CaO. Smaller catalyst particles were formed after the addition of Co into Cu species. It was found that the addition of Co to Cu on the CaO support could fine-tune the appropriate acidic and basic sites to boost the FOL yield and selectivity with suppression of undesired products. These observations could confirm that the high efficiency and selectivity are mainly attributed to the synergistic effect between the catalytically active Co-Cu species and the CaO basic sites. Additionally, the FAL conversion and FOL yield insignificantly changed throughout the third consecutive run, confirming a high stability of the developed Co1.40Cu1/CaO catalyst.

Insight into the Roles of Metal Loading on CO2 Photocatalytic Reduction Behaviors of TiO2.

The photocatalytic reduction of carbon dioxide (CO2) into value-added chemicals is considered to be a green and sustainable technology, and has recently gained considerable research interest. In this work, titanium dioxide (TiO2) supported Pt, Pd, Ni, and Cu catalysts were synthesized by photodeposition. The formation of various metal species on an anatase TiO2 surface, after ultraviolet (UV) light irradiation, was investigated insightfully by the X-ray absorption near edge structure (XANES) technique. CO2 reduction under UV-light irradiation at an ambient pressure was demonstrated. To gain an insight into the charge recombination rate during reduction, the catalysts were carefully investigated by the intensity modulated photocurrent spectroscopy (IMPS) and photoluminescence spectroscopy (PL). The catalytic behaviors of the catalysts were investigated by density functional theory using the self-consistent Hubbard U-correction (DFT+U) approach. In addition, Mott-Schottky measurement was employed to study the effect of energy band alignment of metal-semiconductor on CO2 photoreduction. Heterojunction formed at Pt-, Pd-, Ni-, and Cu-TiO2 interface has crucial roles on the charge recombination and the catalytic behaviors. Furthermore, it was found that Pt-TiO2 provides the highest methanol yield of 17.85 µmol/gcat/h, and CO as a minor product. According to the IMPS data, Pt-TiO2 has the best charge transfer ability, with the mean electron transit time of 4.513 µs. We believe that this extensive study on the junction between TiO2 could provide a profound understanding of catalytic behaviors, which will pave the way for rational designs of novel catalysts with improved photocatalytic performance for CO2 reduction.

Enhancing the catalytic performance of calcium-based catalyst derived from gypsum waste for renewable light fuel production through a pyrolysis process: A study on the effect of magnesium content.

The thermochemical conversion of abundant renewable resources through pyrolytic catalysis cracking (PCC) is one of the most promising technologies for producing green biofuels. In this study, the pyrolysis of palm oil was investigated over a sustainable CaO-based catalyst derived from waste gypsum. PCC was conducted in a continuous packed-bed reactor under atmospheric pressure without purge gas. The effects of Mg doping and reaction temperature were also examined. A wet ball milling process was used to prepare the well-mixed catalysts and to subsequently form a heterojunction structure between the CaO and MgO particles. CaO was synthesized using the Ca(OH)2 derived from the reaction between gypsum and sodium hydroxide. The pyrolytic oil was separated from the crude oil to remove water and other impurities. The pyrolytic oil was then distilled following ASTM D86, and the three separated products were classified as bio-gasoline, bio-kerosene, and bio-diesel. The highest renewable light fuel volume (bio-gasoline and bio-kerosene) of about 75% (74 %wt.) was obtained at a reaction temperature of 525 °C with 10% MgCO3 content. The percent volume of light fuel increased with increasing reaction temperature. Renewable light fuel production over the Mg-doped CaO-based catalyst was related to both the Mg content and reaction temperature.

Self-calcifying lipid nanocarrier for bone tissue engineering.

BACKGROUND: A nanoemulsion with specific surface properties (such as charge and functional groups) can initiate the deposition of calcium phosphate (CaP) on its surface, leading to formation of CaP nanoparticles with a lipid core. The lipid core can carry lipophilic compounds based on the function of the nanoemulsion. Therefore, a dual purpose nanoemulsion of lipid nanoparticles (LNPs) exhibiting self-calcifying and carrier abilities can be developed. METHODS: We employed an emulsification process to formulate LNPs with a specific charged surface. The LNPs were tested for their ability to calcify in simulated body fluid and encapsulate cholecalciferol (a model of active compound). The self-calcifying LNP was successfully fabricated using the emulsification process and stabilized using a mixture of polysorbate 80 and polysorbate 20. RESULTS: The LNPs incubated in simulated body fluid bound to calcium and phosphate, subsequently forming CaP on the particle surface and resulting in approximately 180-nm CaP spheres with a lipid core. The LNPs facilitated calcium phosphate deposition in the collagen scaffolds. In addition, LNPs can be used as carriers of lipophilic compounds without impeding the self-calcifying ability.

Three-Dimensional Hierarchical Porous TiO2 for Enhanced Adsorption and Photocatalytic Degradation of Remazol Dye.

Three-dimensional hierarchical mesoporous structures of titanium dioxide (3D-HPT) were synthesized by self-assembly emulsion polymerization. Polymethyl methacrylate (PMMA) and pluronic 123 (P123) were used as the soft templates and co-templates for assisting the formation of hierarchical 3D porous structures. The TiO2 crystal structure, morphology, and Remazol red dye degradation were investigated. The 3D-HPT and normal three-dimensional titanium dioxide (3D-T) presented the good connection of the nanoparticle-linked honeycomb within the form of anatase. The 3D-HPT structure showed greatly enhanced adsorption of Remazol dye, and facilitated the efficient photocatalytic breakdown of the dye. Surprisingly, 3D-HPT can adsorb approximately 40% of 24 ppm Remazol dye in the dark, which is superior to 3D-T and the commercial anatase at the same condition (approx. 5%). Moreover, 3D-HPT can completely decolorize Remazol dye within just 20 min, which is more than three folds faster than the commercial anatase, making it one of the most active photocatalysts that have been reported for degradation of Remazol dye. The superior photocatalytic performance is attributed to the higher specific surface area, amplified light-harvesting efficiency, and enhanced adsorption capacity into the hierarchical 3D inverse opal structure compared to the commercial anatase TiO2.

In Situ X-ray Absorption Fine Structure Probing-Phase Evolution of CuFe2O4 in Nanospace Confinement.

The thermal transformation of Cu(NO3)2 and (Fe(NO3)3 into a CuFe2O4 spinel structure in the confined space of SBA-15 has been investigated. Interestingly, we observed the new formation mechanism of CuFe2O4 in SBA-15 via isolated metal ions (Cu2+ and Fe3+) surrounded by oxygen atoms, which gradually transformed to CuO and ferrihydrite. The latter evolved to maghemite spinel ferrite and reacted with CuO to form CuFe2O4 as the final species. In contrast, in the nonconfined space where the spinel was produced via a sol-gel combustion method, the nanostructure of CuFe2O4 immediately formed during the sol-gel combustion process and its crystallinity was improved after calcination. This is the first report on probing-phase formation using high-temperature in situ X-ray absorption fine structure.

Structure, dissolution, and plant uptake of ferrous/zinc phosphates.

Development of slow release fertilizers by tuning dissolution kinetics can reduce the environmental impact of (micro) nutrients added to crops. Mixed metal compounds may have different dissolution kinetics and plant uptake than single metal compounds. In this study, mixed Fe(II)/Zn(II) phosphates (0-100 at% Zn) were prepared by aqueous precipitation and their structural characteristics and dissolution kinetics in a sand column were measured as model for divalent metal and phosphate release in soil. Three minerals were identified, namely vivianite (Fe3(PO4)2·8H2O) at 0-20 at% Zn, phosphophyllite (Zn2Fe(PO4)2·4H2O) at 20-79 at% Zn, and hopeite (Zn3(PO4)2·4H2O) at 79-100 at% Zn. The Fe-rich materials had high SSA of 42-64 m2 g-1, which decreased to ≤4 m2 g-1 for ≥79 at% Zn. The Fe K-edge and Zn K-edge XANES spectroscopy measurements show that the samples had comparable local structure and contained 13-72% of Fe as Fe(III) due to partial oxidation. In the sand column, Zn(II) and Fe(II) phosphates dissolved near-congruently at steady state (>7 h), whereas mixed Fe(II)/Zn(II) phosphates showed preferential release of Zn over P and Fe, likely due to reprecipitation of Fe. Pot experiments demonstrate that Zn from Fe(II)/Zn(II) phosphates is absorbed by bird's eye chili plants (C. annuum), in agreement with the preferential dissolution of Zn(II). These results may provide insight into the dissolution of other divalent metals, which not only aids in the growth of plants and resulting foodstuff but ultimately leads to reductions in environmental contamination.

Preparation and electrochemical performance of nitrogen-enriched activated carbon derived from silkworm pupae waste.

In this study, nitrogen-enriched activated carbon from silkworm pupae waste (P-AC) was successfully prepared and its electrochemical performances in aqueous and organic electrolytes were investigated. Silkworm pupae waste is beneficial because it is a nitrogen-enriched, inexpensive, and locally available material. The preparation process includes hydrothermal treatment of the silkworm pupae waste at 200 °C, and chemical activation using zinc chloride at activation temperatures of 700, 800 and 900 °C (P700, P800, and P900, respectively). The nitrogen content in the P-ACs was approximately 3.8-6.4 at%, decreasing with activation temperature, while the surface area was approximately 1062-1267 m2 g-1, increasing with activation temperature. Compared to a commercial AC, the P-ACs show higher nitrogen content but lower surface area. Furthermore, the P800 exhibited superior specific capacitance (154.6 and 91.6 F g-1 in aqueous and organic electrolytes) compared to a commercial AC despite possessing smaller surface area. The high nitrogen content enhanced the pseudocapacitance and improved the electrical conductivity of the P-ACs. These properties were confirmed by relatively low series and charge transfer resistances, a capacity retention higher than 88% at a current density of 0.5 A g-1 and excellent cycling stability demonstrated by maintaining 97.6% of its capacitance after 3000 cycles. These results demonstrate that silkworm pupae waste is a viable source of nitrogen-enriched AC for application in supercapacitors.