RESUMEN
The mass production of high-quality graphene is required for industrial application as a future electronic material. However, the chemical vapor deposition (CVD) systems previously studied for graphene production face bottlenecks in terms of quality, speed, and reproducibility. Herein, we report a novel conveyor CVD system that enables rapid graphene synthesis using liquid precursors. Pristine and nitrogen-doped graphene samples of a size comparable to a smartphone (15 cm × 5 cm) are successfully synthesized at temperatures of 900, 950, and 1000 °C using butane and pyridine, respectively. Raman spectroscopy allows optimization of the rapid-synthesis conditions to achieve uniformity and high quality. By conducting compositional analysis via X-ray photoelectron spectroscopy as well as electrical characterization, it is confirmed that graphene synthesis and nitrogen doping degree can be adjusted by varying the synthesis conditions. Testing the corresponding graphene samples as gas-sensor channels for NH3 and NO2 and evaluating their response characteristics show that the gas sensors exhibit polar characteristics in terms of gas adsorption and desorption depending on the type of gas, with contrasting characteristics depending on the presence or absence of nitrogen doping; nitrogen-doped graphene exhibits superior gas-sensing sensitivity and response speed compared with pristine graphene.
RESUMEN
To investigate the efficacy of the Korean version of the Minnesota low vision reading chart. A Korean version consisting of 38 items was prepared based on the MNREAD acuity chart developed by the University of Minnesota. A linguist composed the representative sentences, each containing nine words from second and third grade levels of elementary school. Reading ability was measured for 20-35-year-old subjects with normal visual acuity (corrected visual acuity of logMAR 0.0 or better). The maximum reading speed (words per minute [wpm]) for healthy participants, reading acuity (smallest detectable font size), and critical print size (smallest font size without reduction of reading speed) were analyzed. The average age of the subjects was 28.3 ± 2.6 years (male:female ratio, 4:16). The average reading time for 38 sentences was 3.66 ± 0.69 s, with no differences in the average maximum reading speed between sentences (p = 0.836). The maximum reading speed was 174.2 ± 29.3 and 175.4 ± 27.8 in the right and left eye, respectively. Reading acuity was measured as logMAR 0.0 or better in 80% of the cases. All subjects showed a critical print size of 0.2 logMAR or better. The overall reading ability can be measured using the Korean version of the MNREAD acuity chart, thereby making it useful in measuring the reading ability of those with Korean as their native language.
Asunto(s)
Pruebas de Visión , Baja Visión , Humanos , Masculino , Femenino , Adulto , Adulto Joven , Agudeza Visual , Lenguaje , República de CoreaRESUMEN
Two-dimensional (2D) vertical van der Waals heterostructures (vdWHs) show great potential across various applications. However, synthesizing large-scale structures poses challenges owing to the intricate growth parameters, forming unexpected hybrid film structures. Thus, precision in synthesis and thorough structural analysis are essential aspects. In this study, we successfully synthesized large-scale structured 2D transition metal dichalcogenides (TMDs) via chemical vapor deposition using metal oxide (WO3 and MoO3) thin films and a diluted H2S precursor, individual MoS2, WS2 films and various MoS2/WS2 hybrid films (Type I: MoxW1-xS2 alloy; Type II: MoS2/WS2 vdWH; Type III: MoS2 dots/WS2). Structural analyses, including optical microscopy, Raman spectroscopy, transmission electron microscopy (TEM) with energy-dispersive X-ray spectroscopy, and cross-sectional imaging revealed that the A1g and E2g modes of WS2 and MoS2 were sensitive to structural variations, enabling hybrid structure differentiation. Type II showed minimal changes in the MoS2's A1g mode, while Types I and III exhibited a ~2.8 cm-1 blue shift. Furthermore, the A1g mode of WS2 in Type I displayed a 1.4 cm-1 red shift. These variations agreed with the TEM-observed microstructural features, demonstrating strain effects on the MoS2-WS2 interfaces. Our study provides insights into the structural features of diverse hybrid TMD materials, facilitating their differentiation through Raman spectroscopy.
RESUMEN
Transition metal dichalcogenides (TMDs) benefit electrical devices with spin-orbit coupling and valley- and topology-related properties. However, TMD-based devices suffer from traps arising from defect sites inside the channel and the gate oxide interface. Deactivating them requires independent treatments, because the origins are dissimilar. This study introduces a single treatment to passivate defects in a multilayer MoS2 FET. By applying back-gate bias, protons from an H-TFSI droplet are injected into the MoS2, penetrating deeply enough to reach the SiO2 gate oxide. The characterizations employing low-temperature transport and deep-level transient spectroscopy (DLTS) studies reveal that the trap density of S vacancies in MoS2 drops to the lowest detection level. The temperature-dependent mobility plot on the SiO2 substrate resembles that of the h-BN substrate, implying that dangling bonds in SiO2 are passivated. The carrier mobility on the SiO2 substrate is enhanced by approximately 2200% after the injection.
RESUMEN
The objective of this study was to investigate the usefulness of fibrinogen-to-albumin ratio (FAR) as a prognostic marker in patients admitted to an intensive care unit (ICU) compared with Sequential Organ Failure Assessment (SOFA) score, a widely used prognostic scoring system. An inverse probability weighting (IPW) was used to control for selection bias and confounding factors. After IPW adjustment, the high FAR group showed significantly higher risk of 1-year compared with low FAR group (36.4% vs. 12.4%, adjust hazard ratio = 1.72; 95% confidence interval (CI): 1.59-1.86; p < 0.001). In the receiver-operating characteristic curve analysis associated with the prediction of 1-year mortality, there was no significant difference between the area under the curve of FAR on ICU admission (C-statistic: 0.684, 95% CI: 0.673-0.694) and that of SOFA score on ICU admission (C-statistic: 0.679, 95% CI: 0.669-0.688) (p = 0.532). In this study, FAR and SOFA score at ICU admission were associated with 1-year mortality in patients admitted to an ICU. Especially, FAR was easier to obtain in critically ill patients than SOFA score. Therefore, FAR is feasible and might help predict long-term mortality in these patients.
RESUMEN
A low interfacial contact resistance is a challenge in polymer nanocomposites based on conductive nanomaterials for high-performance wearable electrode applications. Herein, a polydimethylsiloxane (PDMS)-based flexible nanocomposite incorporating high-conductivity 1D single-walled carbon nanotubes (SWCNTs) and 2D reduced graphene oxide (r-GO) was developed for high-performance electrocardiogram (ECG) wearable electrodes. A PDMS-SWCNT (P-SW; type I) nanocomposite containing only SWCNTs (2 wt%), exhibited rough and non-uniform surface morphology owing to the strong bundling effect of as-grown SWCNTs and randomly entangled aggregate structures and because of inefficient vacuum degassing (i.e., R P-SW = 1871 Ω). In contrast, owing to the hybrid structure of the SWCNTs (1 wt%) and r-GO (1 wt%), the PDMS-SWCNTs/r-GO (P-SW/r-GO; type II) nanocomposite exhibited uniform surface characteristics and low contact resistance (i.e., R P-SW/r-GO = 63 Ω) through the formation of hybrid and long conducting pathways. The optimized nanocomposite (P-SW/r-GO/f; type III) possessed a fabric-assisted structure that enabled tunable and efficient vacuum degassing and curing conditions. Additionally, a long and wide conducting pathway was formed through more uniform and dense interconnected structures, and the contact resistance was drastically reduced (i.e., R P-SW/r-GO/f = 15 Ω). The performance of the electrodes fabricated using the optimized nanocomposites was the same or higher than that of commercial Ag/AgCl gel electrodes during real-time measurement for ECG Bluetooth monitoring. The developed high-performance hybrid conducting polymer electrodes are expected to contribute significantly to the expansion of the application scope of wearable electronic devices and wireless personal health monitoring systems.
RESUMEN
OBJECTIVE: To compare and analyze the differences in the sociodemographic and clinical characteristics of suicide attempters who visited an emergency department (ED) before and during the coronavirus disease (COVID-19) pandemic. METHODS: This single center, retrospective study was conducted by reviewing the medical records of patients in the "self-injury/suicide" category of the National Emergency Department Information System who visited an ED between January 2019 and December 2020. We obtained information on baseline characteristics, suicide attempt, and disposition. Data were analyzed using the chi-squared test. RESULTS: A total of 456 patients were included. The number of patients visiting the ED for suicide attempts increased by 18.2% (from 209 to 247 cases) during the COVID-19 pandemic, and the ratio of suicide attempters to the total number of ED visits increased by 48.8% (from 0.43% to 0.64%, P<0.001). There were significant differences in methods of suicide attempt, endotracheal intubation, ED disposition, and the presence of mental illness. Drug overdose (42.1% vs. 53.4%) and gas inhalation (5.7% vs. 8.5%) increased, and hanging decreased (6.0% vs. 2.0%) during the pandemic. Endotracheal intubation (13.9% vs. 5.7%) and intensive care unit admission (29.7% vs. 14.6%) decreased. More patients with the history of mental illness visited during the pandemic (54.0% vs. 70.1%). CONCLUSION: Since the COVID-19 pandemic began, suicide attempts have increased in this single ED although the lethality of those attempts is low.
RESUMEN
A recent study found that magnetization curves for Y3Fe5O12 (YIG) slab and thick films (>20 µm thick) differed from bulk system curves by their longitudinal spin Seebeck effect in a Pt/YIG bilayer system. The deviation was due to intrinsic YIG surface magnetic anisotropy, which is difficult to adopt extrinsic surface magnetic anisotropy even when in contact with other materials on the YIG surface. This study experimentally demonstrates evidence for extrinsic YIG surface magnetic anisotropy when in contact with a diamagnetic graphene interlayer by observing the spin Seebeck effect, directly proving intrinsic YIG surface magnetic anisotropy interruption. We show the Pt/YIG bilayer system graphene interlayer role using large area single and multilayered graphenes using the longitudinal spin Seebeck effect at room temperature, and address the presence of surface magnetic anisotropy due to magnetic proximity between graphene and YIG layer. These findings suggest a promising route to understand new physics of spin Seebeck effect in spin transport.
RESUMEN
The excellent physical and chemical properties of carbon nanomaterials render them suitable for application in gas sensors. However, the synthesis of carbon nanomaterials using high-temperature furnaces is time consuming and expensive. In this study, we synthesize a carbon nanomaterial using local laser-scribing on a substrate coated with a Cu-embedded polyimide (PI) thin film to reduce the processing time and cost. Spin coating using a Cu-embedded PI solution is performed to deposit a Cu-embedded PI thin film (Cu@PI) on a quartz substrate, followed by the application of a pulsed laser for carbonization. In contrast to a pristine PI solution-based PI thin film, the laser absorption of the Cu-embedded PI thin film based on Cu@PI improved. The laser-scribed carbon nanomaterial synthesized using Cu@PI exhibits a three-dimensional structure that facilitates gas molecule absorption, and when it is exposed to NO2 and NH3, its electrical resistance changes by -0.79% and +0.33%, respectively.
RESUMEN
Carbon nanomaterials have attracted significant research attention as core materials in various industrial sectors owing to their excellent physicochemical properties. However, because the preparation of carbon materials is generally accompanied by high-temperature heat treatment, it has disadvantages in terms of cost and process. In this study, highly sensitive carbon nanomaterials were synthesized using a local laser scribing method from a copper-embedded polyacrylonitrile (CuPAN) composite film with a short processing time and low cost. The spin-coated CuPAN was converted into a carbonization precursor through stabilization and then patterned into a carbon nanomaterial of the desired shape using a pulsed laser. In particular, the stabilization process was essential in laser-induced carbonization, and the addition of copper promoted this effect as a catalyst. The synthesized material had a porous 3D structure that was easy to detect gas, and the resistance responses were detected as -2.41 and +0.97% by exposure to NO2 and NH3, respectively. In addition, the fabricated gas sensor consists of carbon materials and quartz with excellent thermal stability; therefore, it is expected to operate as a gas sensor even in extreme environments.
RESUMEN
In this study, we describe the adsorption behavior of water (H2O) in the interstitial space of single-walled carbon nanotubes (SWCNTs). A highly dense SWCNT (HD-SWCNT) film with a remarkably enhanced interstitial space was fabricated through mild HNO3/H2SO4 treatment. The N2, CO2, and H2 adsorption isotherm results indicated remarkably developed micropore volumes (from 0.10 to 0.40 mL g-1) and narrower micropore widths (from 1.5 to 0.9 nm) following mild HNO3/H2SO4 treatment, suggesting that the interstitial space was increased from the initial densely-packed network assembly structure of the SWCNTs. The H2O adsorption isotherm of the HD-SWCNT film at 303 K showed an increase in H2O adsorption (i.e., by â¼170%), which increased rapidly from the critical value of relative pressure (i.e., 0.3). Despite the remarkably enhanced adsorption capacity of H2O, the rates of H2O adsorption and desorption in the interstitial space did not change. This result shows an adsorption behavior different from that of the fast transport of H2O molecules in the internal space of the SWCNTs. In addition, the adsorption capacities of N2, CO2, H2, and H2O molecules in the interstitial space of the HD-SWCNT film showed a linear relationship with the kinetic diameter, indicating an adsorption behavior that is highly dependent on the kinetic diameter.
RESUMEN
Over the past decades, graphene has attracted much attention from the scientific community due to its broad applications in the optoelectronics industries [1]. Owing to graphene's high transmission and high electrical conductivity, diverse functional materials/graphene hybridized heterostructures and interfaces are under extensive investigation to satisfy the increasing interest in the need for bendable, flexible and high performance optoelectronic devices [2]. Due to the good atomic lattice structure of graphene, varying heterostructures have been formed by depositing different functional materials directly on graphene [3], [4], [5]. We fabricated a vertical photovoltaic type G/PbS/Ti device by making use of the Ti/PbS Schottky junction and discussed the photocurrent transient characteristics. Lead sulfide (PbS) was deposited directly on large area CVD (Chemical vapor deposition) graphene by CBD (Chemical bath deposition). Temperature dependent photocurrent spectra of our G/PbS/Ti photovoltaic devices were measured by a Fourier transformed infrared (FTIR) set-up. In this paper, we present the experimental procedures and the raw experimental data for the direct chemical deposition of PbS on CVD-graphene for high performance photovoltaic infrared photo-detectors. The manuscript is already available [6].
RESUMEN
We investigated the heat transfer behavior of thermally conductive networks with one-dimensional carbon materials to design effective heat transfer pathways for hybrid filler systems of polymer matrix composites. Nano-sized few-walled carbon nanotubes (FWCNTs) and micro-sized mesophase pitch-based carbon fibers (MPCFs) were used as the thermally conductive materials. The bulk density and thermal conductivity of the FWCNT films increased proportionally with the ultrasonication time due to the enhanced dispersibility of the FWCNTs in an ethanol solvent. The ultrasonication-induced densification of the FWCNT films led to the effective formation of filler-to-filler connections, resulting in improved thermal conductivity. The thermal conductivity of the FWCNT-MPCF hybrid films was proportional to the MPCF content (maximum thermal conductivity at an MPCF content of 60 wt %), indicating the synergistic effect on the thermal conductivity enhancement. Moreover, the MPCF-to-MPCF heat transfer pathways in the FWCNT-MPCF hybrid films were the most effective in achieving high thermal conductivity due to the smaller interfacial area and shorter heat transfer pathway of the MPCFs. The FWCNTs could act as thermal bridges between neighboring MPCFs for effective heat transfer. Furthermore, the incorporation of Ag nanoparticles of approximately 300 nm into the FWCNT-MPCF hybrid film dramatically enhanced the thermal conductivity, which was closely related to a decreased thermal interfacial resistance at the intersection points between the materials. Epoxy-based composites loaded with the FWCNTs, MPCFs, FWCNT-MPCF hybrids, and FWCNT-MPCF-Ag hybrid fillers were also fabricated. A similar trend in thermal conductivity was observed in the polymer matrix composite with carbon-based hybrid films.
RESUMEN
We developed a new technique to fabricate single nanowire devices with reliable graphene/nanowire contacts using a position-controlled microtransfer and an embedded nanowire structure in a planar junction configuration. A thorough study of electrical properties and fabrication challenges of single p-GaAs nanowire/graphene devices was carried out in two different device configurations: (1) a graphene bottom-contact device where the nanowire-graphene contact junction is formed by transferring a nanowire on top of graphene and (2) a graphene top-contact device where the nanowire-graphene contact junction is formed by transferring graphene on top of an embedded nanowire. For the graphene top-contact devices, graphene-nanowire-metal devices, where graphene is used as one electrode and metal is the other electrode to a nanowire, and graphene-nanowire-graphene devices, where both electrodes to a nanowire are graphene, were investigated and compared with conventional metal/p-GaAs nanowire devices. Conventional metal/p-GaAs nanowire contact devices were further investigated in embedded and nonembedded nanowire device configurations. A significantly improved current in the embedded device configuration is explained with a "parallel resistors model" where the high-resistance parts with the metal-semiconductor Schottky contact and the low-resistance parts with noncontacted facets of the hexagonal nanowires are taken into consideration. Consistently, the nonembedded nanowire structure is found to be depleted much easier than the embedded nanowires from which an estimation for a fully depleted condition has also been established.
RESUMEN
Recent development in mobile electronic devices and electric vehicles requires electrical wires with reduced weight as well as enhanced stability. In addition, since electric energy is mostly generated from power plants located far from its consuming places, mechanically stronger and higher electric power transmission cables are strongly demanded. However, there has been no alternative materials that can practically replace copper materials. Here, we report a method to prepare ultrastrong graphene fibers (GFs)-Cu core-shell wires with significantly enhanced electrical and mechanical properties. The core GFs are synthesized by chemical vapor deposition, followed by electroplating of Cu shells, where the large surface area of GFs in contact with Cu maximizes the mechanical toughness of the core-shell wires. At the same time, the unique electrical and thermal characteristics of graphene allow a â¼10 times higher current density limit, providing more efficient and reliable delivery of electrical energies through the GFs-Cu wires. We believe that our results would be useful to overcome the current limit in electrical wires and cables for lightweight, energy-saving, and high-power applications.
RESUMEN
BACKGROUND: Single or combined multiple-site peripheral nerve blocks (PNBs) are becoming popular for patients undergoing surgery on their feet or ankles. These procedures are known to be generally safe in surgical settings compared with other forms of anesthesia, such as spinal block. The purposes of this study were to assess the incidence of complications after the administration of multiple PNBs for foot and ankle surgery and to compare the rates of complications between patients who received a single PNB and those who received multiple blocks. METHODS: Charts were reviewed retrospectively to assess peri- and postoperative complications possibly related to the PNBs. The records of 827 patients who had received sciatic nerve blocks, femoral nerve blocks adductor canal blocks, or combinations of these for foot and/or ankle surgery were analyzed for complications. The collected data consisted of age, sex, body mass index, presence of diabetes mellitus, smoking history, tourniquet time, and complications both immediately postoperatively and 1 year later. RESULTS: Of these 827 patients, 92 (11.1%) developed neurologic symptoms after surgery; 22 (2.7%) of these likely resulted from the nerve blocks, and 7 (0.8%) of these were unresolved after the patients' last follow-up visits. There were no differences in complication rates between combined blocks and single sciatic nerve blocks. CONCLUSION: There were more complications, both transient and long term, after anesthetic PNBs than previous literature has reported. Combined multiple-site blocks did not increase the rate of neurologic complications. LEVEL OF EVIDENCE: Level III, retrospective comparative study.
Asunto(s)
Anestésicos Locales/administración & dosificación , Tobillo/cirugía , Bloqueo Nervioso/métodos , Procedimientos Ortopédicos/métodos , Complicaciones Posoperatorias/epidemiología , Nervio Ciático/fisiología , Humanos , Inyecciones , Estudios RetrospectivosRESUMEN
Despite recent progress in producing flexible and stretchable electronics based on two-dimensional (2D) nanosheets, their intrinsic properties are often degraded by the presence of polymeric residues that remain attached to the 2D nanosheet surfaces following fabrication. Further breakthroughs are therefore keenly awaited to obtain clean surfaces compatible with flexible applications. Here, we report a method that allows the 2D nanosheets to be intrinsically integrated onto flexible substrates. The method involves thermal decomposition of polymeric residues by microwave-induced ultrafast heating of the surface without affecting the underlying flexible substrate. Mapping the CâO stretching mode by Fourier-transform infrared spectroscopy in combination with atomic force microscopy confirms elimination of the polymeric residues from the 2D nanosheet surface. Flexible devices prepared using microwave-cleaned 2D nanosheets show enhanced electrical, optical, and electrothermal performances. This simple technique is applicable to a wide range of 2D nanomaterials and represents an important advance in the field of flexible devices.
RESUMEN
To predict carcinogenic potential of AgNPs on the respiratory system, BEAS-2B cells (human bronchial epithelial cells) were chronically exposed to low- and non-cytotoxic dose (0.13 and 1.33µg/ml) of AgNPs for 4months (#40 passages). To assess malignant cell transformation of chronic exposure to AgNPs, several bioassays including anchorage independent agar colony formation, cell migration/invasion assay, and epithelial-mesenchymal transition (EMT) were performed in BEAS-2B cells. Chronic exposure to AgNPs showed a significant increase of anchorage independent agar colony formation and cell migration/invasion. EMT, which is the loss of epithelial markers (E-Cadherin and Keratin) and the gain of mesenchymal marker (N-cadherin and Vimentin), was induced by chronic exposure to AgNPs. These responses indicated that chronic exposure to AgNPs could acquire characteristics of tumorigenic cells from normal BEAS-2B cells. In addition, caspase-3, p-p53, p-p38, and p-JNK were significantly decreased, while p-ERK1/2 was significantly increased. MMP-9 related to cell migration/invasion was upregulated, while a MMP-9 inhibitor, TIMP-1 was down-regulated. These results indicated that BEAS-2B cells exposed to AgNPs could induce anti-apoptotic response/anoikis resistance, and cell migration/invasion by complex regulation of MAPK kinase (p38, JNK, and ERK) and p53 signaling pathways. Therefore, we suggested that long-term exposure to low-dose of AgNPs could enhance malignant cell transformation in non-tumorigenic BEAS-2B cells. Our findings provide useful information needed to assess the carcinogenic potential of AgNPs.
Asunto(s)
Transformación Celular Neoplásica/efectos de los fármacos , Nanopartículas del Metal/toxicidad , Plata/toxicidad , Antígenos CD/metabolismo , Cadherinas/metabolismo , Caspasa 3/genética , Línea Celular , Movimiento Celular/efectos de los fármacos , Supervivencia Celular/efectos de los fármacos , Transición Epitelial-Mesenquimal , Humanos , Queratinas/metabolismo , Metaloproteinasa 9 de la Matriz/metabolismo , Proteínas Proto-Oncogénicas c-bcl-2/genética , ARN Mensajero/metabolismo , Inhibidor Tisular de Metaloproteinasa-1/metabolismo , Proteína p53 Supresora de Tumor/genética , Vimentina/metabolismo , Proteína X Asociada a bcl-2/genéticaRESUMEN
Control of living cells on biocompatible materials or on modified substrates is important for the development of bio-applications, including biosensors and implant biomaterials. The topography and hydrophobicity of substrates highly affect cell adhesion, growth, and cell growth kinetics, which is of great importance in bio-applications. Herein, we investigate the adhesion, growth, and morphology of cultured breast cancer cells on a silicon substrate, on which graphene oxides (GO) was partially formed. By minimizing the size and amount of the GO-containing solution and the further annealing process, GO-coated Si samples were prepared which partially covered the Si substrates. The coverage of GO on Si samples decreases upon annealing. The behaviors of cells cultured on two samples have been observed, i.e. partially GO-coated Si (P-GO) and annealed partially GO-coated Si (Annealed p-GO), with a different coverage of GO. Indeed, the spreading area covered by the cells and the number of cells for a given culture period in the incubator were highly dependent on the hydrophobicity and the presence of oxygenated groups on GO and Si substrates, suggesting hydrophobicity-driven cell growth. Thus, the presented method can be used to control the cell growth via an appropriate surface modification.