RESUMEN
Despite the fundamental and technological importance of the elastic constants, a suitable method for their full characterization in epitaxial films is missing. Here we show that transient grating spectroscopy (TGS) with highly k-vector-selective generation and detection of acoustic waves is capable of determination of all independent elastic coefficients of an epitaxial thin film grown on a single-crystalline substrate. This experimental setup enables detection of various types of guided acoustic waves and evaluation of the directional dependence of their speeds of propagation. For the studied model system, which is a 3µm thin epitaxial film of the NiTi shape memory alloy on an MgO substrate, the TGS angular maps include Rayleigh-type surface acoustic waves as well as Sezawa-type and Love-type modes, delivering rich information on the elastic response of the film under different straining modes. The resulting inverse problem, which means the calculation of the elastic constants from the TGS maps, is subsequently solved using the Ritz-Rayleigh numerical method. Using this approach, tetragonal elastic constants of the NiTi film and their changes with the austeniteâmartensite phase transition are analyzed.
RESUMEN
During cooling, conventional martensitic transformation can only be realized from austenite to martensite. Recently, a so-called reentrant martensitic transformation attracted much interest due to an additional transformation from martensite to austenite during further cooling. Obviously, materials with this reentrant transformation will increase the number of physical effects and possible applications. However, until now, only bulk samples have been available, which are not suitable for applications in micro-devices. In this work, we focus on the Co-Cr-Ga-Si system and examine the suitability of this system for the growth of thin films. We observed that the films grow epitaxially on MgO (100) substrates and exhibit a martensitic transformation if deposited at a sufficiently high temperature or with an additional heat treatment. Films within the austenite state are ferromagnetic while films within the martensitic state just exhibit a very low ferromagnetic order.
RESUMEN
Structural martensitic transformations enable various applications, which range from high stroke actuation and sensing to energy efficient magnetocaloric refrigeration and thermomagnetic energy harvesting. All these emerging applications benefit from a fast transformation, but up to now their speed limit has not been explored. Here, we demonstrate that a thermoelastic martensite to austenite transformation can be completed within 10 ns. We heat epitaxial Ni-Mn-Ga films with a nanosecond laser pulse and use synchrotron diffraction to probe the influence of initial temperature and overheating on transformation rate and ratio. We demonstrate that an increase in thermal energy drives this transformation faster. Though the observed speed limit of 2.5 × 1027 (Js)1 per unit cell leaves plenty of room for further acceleration of applications, our analysis reveals that the practical limit will be the energy required for switching. Thus, martensitic transformations obey similar speed limits as in microelectronics, as expressed by the Margolus - Levitin theorem.
RESUMEN
Magnetocaloric materials based on field-induced first order transformations such as Ni-Mn-Ga-Co are promising for more environmentally friendly cooling. Due to the underlying martensitic transformation, a large hysteresis can occur, which in turn reduces the efficiency of a cooling cycle. Here, we analyse the influence of the film microstructure on the thermal hysteresis and focus especially on large angle grain boundaries. We control the microstructure and grain boundary density by depositing films with local epitaxy on different substrates: Single crystalline MgO(0 0 1), MgO(1 1 0) and Al2O3(0 0 0 1). By combining local electron backscatter diffraction (EBSD) and global texture measurements with thermomagnetic measurements, we correlate a smaller hysteresis with the presence of grain boundaries. In films with grain boundaries, the hysteresis is decreased by about 30% compared to single crystalline films. Nevertheless, a large grain boundary density leads to a broadened transition. To explain this behaviour, we discuss the influence of grain boundaries on the martensitic transformation. While grain boundaries act as nucleation sites, they also lead to different strains in the material, which gives rise to various transition temperatures inside one film. We can show that a thoughtful design of the grain boundary microstructure is an important step to optimize the hysteresis.
