RESUMEN
Anion exchange membrane (AEM) fuel cells (AEMFCs) and water electrolyzers (AEMWEs) suffer from insufficient performance and durability compared with commercialized energy conversion systems. Great efforts have been devoted to designing high-quality AEMs and catalysts. However, the significance of the stability of the catalyst layer has been largely disregarded. Here, an in situ cross-linking strategy was developed to promote the interactions within the catalyst layer and the interactions between catalyst layer and AEM. The adhesion strength of the catalyst layer after cross-linking was improved 7 times compared with the uncross-linked catalyst layer due to the formation of covalent bonds between the catalyst layer and AEM. The AEMFC can be operated under 0.6 A cm-2 for 1000 h with a voltage decay rate of 20 µV h-1. The related AEMWE achieved an unprecedented current density of 15.17 A cm-2 at 2.0 V and was operated at 0.5, 1.0, and 1.5 A cm-2 for 1000 h.
RESUMEN
The rational design of the current anion exchange polyelectrolytes (AEPs) is challenging to meet the requirements of both high performance and durability in anion exchange membrane water electrolyzers (AEMWEs). Herein, highly-rigid-twisted spirobisindane monomer is incorporated in poly(aryl-co-aryl piperidinium) backbone to construct continuous ionic channels and to maintain dimensional stability as promising materials for AEPs. The morphologies, physical, and electrochemical properties of the AEPs are investigated based on experimental data and molecular dynamics simulations. The present AEPs possess high free volumes, excellent dimensional stability, hydroxide conductivity (208.1 mS cm-1 at 80 °C), and mechanical properties. The AEMWE of the present AEPs achieves a new current density record of 13.39 and 10.7 A cm-2 at 80 °C by applying IrO2 and nonprecious anode catalyst, respectively, along with outstanding in situ durability under 1 A cm-2 for 1000 h with a low voltage decay rate of 53 µV h-1 . Moreover, the AEPs can be applied in fuel cells and reach a power density of 2.02 W cm-2 at 80 °C under fully humidified conditions, and 1.65 W cm-2 at 100 °C, 30% relative humidity. This study provides insights into the design of high-performance AEPs for energy conversion devices.
RESUMEN
Alkaline polymer electrolytes (APEs) are essential materials for alkaline energy conversion devices such as anion exchange membrane fuel cells (AEMFCs) and water electrolyzers (AEMWEs). Here, we report a series of branched poly(aryl-co-aryl piperidinium) with different branching agents (triptycene: highly-rigid, three-dimensional structure; triphenylbenzene: planar, two-dimensional structure) for high-performance APEs. Among them, triptycene branched APEs showed excellent hydroxide conductivity (193.5â mS cm-1 @80 °C), alkaline stability, mechanical properties, and dimensional stability due to the formation of branched network structures, and increased free volume. AEMFCs based on triptycene-branched APEs reached promising peak power densities of 2.503 and 1.705â W cm-2 at 75/100 % and 30/30 % (anode/cathode) relative humidity, respectively. In addition, the fuel cells can run stably at a current density of 0.6â A cm-2 for 500â h with a low voltage decay rate of 46â µV h-1 . Importantly, the related AEMWE achieved unprecedented current densities of 16â A cm-2 and 14.17â A cm-2 (@2â V, 80 °C, 1â M NaOH) using precious and non-precious metal catalysts, respectively. Moreover, the AEMWE can be stably operated under 1.5â A cm-2 at 60 °C for 2000â h. The excellent results suggest that the triptycene-branched APEs are promising candidates for future AEMFC and AEMWE applications.
RESUMEN
Anion exchange membrane fuel cells (AEMFCs) and water electrolysis (AEMWE) show great application potential in the field of hydrogen energy conversion technology. However, scalable anion exchange membranes (AEMs) with desirable properties are still lacking, which greatly hampers the commercialization of this technology. Herein, we propose a series of novel multiblock AEMs based on ether-free poly(biphenyl ammonium-b-biphenyl phenyl)s (PBPA-b-BPPs) that are suitable for use in high performance AEMFC and AEMWE systems because of their well-formed microphase separation structures. The developed AEMs achieved outstanding OH- conductivity (162.2â mS cm-1 at 80 °C) with a low swelling ratio, good alkaline stability, and excellent mechanical durability (tensile strength >31â MPa and elongation at break >147 % after treatment in 2â M NaOH at 80 °C for 3750â h). A PBPA-b-BPP-based AEMFC demonstrated a remarkable peak power density of 2.41â W cm-2 and in situ durability for 330â h under 0.6â A cm-2 at 70 °C. An AEMWE device showed a promising performance (6.25â A cm-2 at 2â V, 80 °C) and outstanding in situ durability for 3250â h with a low voltage decay rate (<28â µV h-1 ). The newly developed PBPA-b-BPP AEMs thus show great application prospects for energy conversion devices.
RESUMEN
The lack of anion exchange membranes (AEMs) that possess both high hydroxide conductivity and stable mechanical and chemical properties poses a major challenge to the development of high-performance fuel cells. Improving one side of the balance between conductivity and stability usually means sacrificing the other. Herein, we used facile, high-yield chemical reactions to design and synthesize a piperidinium polymer with a polyethylene backbone for AEM fuel cell applications. To improve the performance, we introduced ionic crosslinking into high-cationic-ratio AEMs to suppress high water uptake and swelling while further improving the hydroxide conductivity. Remarkably, PEP80-20PS achieved a hydroxide conductivity of 354.3â mS cm-1 at 80 °C while remaining mechanically stable. Compared with the base polymer PEP80, the water uptake of PEP80-20PS decreased by 69 % from 813 % to 350 %, and the swelling decreased substantially by 85 % from 350.0 % to 50.2 % at 80 °C. PEP80-20PS also showed excellent alkaline stability, 84.7 % remained after 35â days of treatment with an aqueous KOH solution. The chemical design in this study represents a significant advancement toward the development of simultaneously highly stable and conductive AEMs for fuel cell applications.
RESUMEN
Anion-exchange-membrane fuel cells (AEMFCs) are a cost-effective alternative to proton-exchange-membrane fuel cells (PEMFCs). The development of high-performance and durable AEMFCs requires highly conductive and robust anion-exchange membranes (AEMs). However, AEMs generally exhibit a trade-off between conductivity and dimensional stability. Here, a fluorination strategy to create a phase-separated morphological structure in poly(aryl piperidinium) AEMs is reported. The highly hydrophobic perfluoroalkyl side chains augment phase separation to construct interconnected hydrophilic channels for anion transport. As a result, these fluorinated PAP (FPAP) AEMs simultaneously possess high conductivity (>150 mS cm-1 at 80 °C) and high dimensional stability (swelling ratio <20% at 80 °C), excellent mechanical properties (tensile strength >80 MPa and elongation at break >40%) and chemical stability (>2000 h in 3 m KOH at 80 °C). AEMFCs with a non-precious Co-Mn spinel cathode using the present FPAP AEMs achieve an outstanding peak power density of 1.31 W cm-2 . The AEMs remain stable over 500 h of fuel cell operation at a constant current density of 0.2 A cm-2 .
RESUMEN
Anion-exchange membrane fuel cells (AEMFCs) are a promising, next-generation fuel cell technology. AEMFCs require highly conductive and robust anion-exchange membranes (AEMs), which are challenging to develop due to the tradeoff between conductivity and water uptake. Here we report a method to prepare high-molecular-weight branched poly(aryl piperidinium) AEMs. We show that branching reduces water uptake, leading to improved dimensional stability. The optimized membrane, b-PTP-2.5, exhibits simultaneously high OH- conductivity (>145â mS cm-1 at 80 °C), high mechanical strength and dimensional stability, good processability, and excellent alkaline stability (>1500â h) in 1â M KOH at 80 °C. AEMFCs based on b-PTP-2.5 reached peak power densities of 2.3â W cm-2 in H2 -O2 and 1.3â W cm-2 in H2 -air at 80 °C. The AEMFCs can run stably under a constant current of 0.2â A cm-2 over 500â h, during which the b-PTP-2.5 membrane remains stable.
RESUMEN
In membrane-based separation, molecular size differences relative to membrane pore sizes govern mass flux and separation efficiency. In applications requiring complex molecular differentiation, such as in natural gas processing, cascaded pore size distributions in membranes allow different permeate molecules to be separated without a reduction in throughput. Here, we report the decoration of microporous polymer membrane surfaces with molecular fluorine. Molecular fluorine penetrates through the microporous interface and reacts with rigid polymeric backbones, resulting in membrane micropores with multimodal pore size distributions. The fluorine acts as angstrom-scale apertures that can be controlled for molecular transport. We achieved a highly effective gas separation performance in several industrially relevant hollow-fibrous modular platform with stable responses over 1 year.
RESUMEN
The alkaline stability of N-heterocyclic ammonium (NHA) groups is a critical topic in anion-exchange membranes (AEMs) and AEM fuel cells (AEMFCs). Here, we report a systematic study on the alkaline stability of 24 representative NHA groups at different hydration numbers (λ) at 80 °C. The results elucidate that γ-substituted NHAs containing electron-donating groups display superior alkaline stability, while electron-withdrawing substituents are detrimental to durable NHAs. Density-functional-theory calculations and experimental results suggest that nucleophilic substitution is the dominant degradation pathway in NHAs, while Hofmann elimination is the primary degradation pathway for NHA-based AEMs. Different degradation pathways determine the alkaline stability of NHAs or NHA-based AEMs. AEMFC durability (from 1â A cm-2 to 3â A cm-2 ) suggests that NHA-based AEMs are mainly subjected to Hofmann elimination under 1â A cm-2 current density for 1000â h, providing insights into the relationship between current density, λ value, and durability of NHA-based AEMs.
RESUMEN
Low-cost anion exchange membrane fuel cells have been investigated as a promising alternative to proton exchange membrane fuel cells for the last decade. The major barriers to the viability of anion exchange membrane fuel cells are their unsatisfactory key components-anion exchange ionomers and membranes. Here, we present a series of durable poly(fluorenyl aryl piperidinium) ionomers and membranes where the membranes possess high OH- conductivity of 208 mS cm-1 at 80 °C, low H2 permeability, excellent mechanical properties (84.5 MPa TS), and 2000 h ex-situ durability in 1 M NaOH at 80 °C, while the ionomers have high water vapor permeability and low phenyl adsorption. Based on our rational design of poly(fluorenyl aryl piperidinium) membranes and ionomers, we demonstrate alkaline fuel cell performances of 2.34 W cm-2 in H2-O2 and 1.25 W cm-2 in H2-air (CO2-free) at 80 °C. The present cells can be operated stably under a 0.2 A cm-2 current density for ~200 h.
RESUMEN
Aryl-ether-free anion-exchange ionomers (AEIs) and membranes (AEMs) have become an important benchmark to address the insufficient durability and power-density issues associated with AEM fuel cells (AEMFCs). Here, we present aliphatic chain-containing poly(diphenyl-terphenyl piperidinium) (PDTP) copolymers to reduce the phenyl content and adsorption of AEIs and to increase the mechanical properties of AEMs. Specifically, PDTP AEMs possess excellent mechanical properties (storage modulus>1800â MPa, tensile strength>70â MPa), H2 fuel-barrier properties (<10â Barrer), good ion conductivity, and ex-situ stability. Meanwhile, PDTP AEIs with low phenyl content and high-water permeability display excellent peak power densities (PPDs). The present AEMFCs reach outstanding PPDs of 2.58â W cm-2 (>7.6â A cm-2 current density) and 1.38â W cm-2 at 80 °C in H2 /O2 and H2 /air, respectively, along with a specific power (PPD/catalyst loading) over 8â W mg-1 , which is the highest record for Pt-based AEMFCs so far.
RESUMEN
Artificial lung (AL) membranes are used for blood oxygenation for patients undergoing open-heart surgery or acute lung failures. Current AL technology employs polypropylene and polymethylpentene membranes. Although effective, these membranes suffer from low biocompatibility, leading to undesired blood coagulation and hemolysis over a long term. In this work, we propose a new generation of AL membranes based on amphiphobic fluoropolymers. We employed poly(vinylidene-co-hexafluoropropylene), or PVDF-co-HFP, to fabricate macrovoid-free membranes with an optimal pore size range of 30-50 nm. The phase inversion behavior of PVDF-co-HFP was investigated in detail for structural optimization. To improve the wetting stability of the membranes, the fabricated membranes were coated using Hyflon AD60X, a type of fluoropolymer with an extremely low surface energy. Hyflon-coated materials displayed very low protein adsorption and a high contact angle for both water and blood. In the hydrophobic spectrum, the data showed an inverse relationship between the surface free energy and protein adsorption, suggesting an appropriate direction with respect to biocompatibility for AL research. The blood oxygenation performance was assessed using animal sheep blood, and the fabricated fluoropolymer membranes showed competitive performance to that of commercial polyolefin membranes without any detectable hemolysis. The data also confirmed that the bottleneck in the blood oxygenation performance was not the membrane permeance but rather the rate of mass transfer in the blood phase, highlighting the importance of efficient module design.
Asunto(s)
Membranas Artificiales , Polivinilos , Adsorción , Animales , Humanos , Pulmón , Membranas , OvinosRESUMEN
Two-dimensional nanosheets have shown great potential for separation applications because of their exceptional molecular transport properties. Nanosheet materials such as graphene oxides, metal-organic frameworks, and covalent organic frameworks display unique, precise, and fast molecular transport through nanopores and/or nanochannels. However, the dimensional instability of nanosheets in harsh environments diminishes the membrane performance and hinders their long-term operation in various applications such as gas separation, water desalination, and ion separation. Recent progress in nanosheet membranes has included modification by crosslinking and functionalization that has improved the stability of the membranes, their separation functionality, and the scalability of membrane formation while the membranes' excellent molecular transport properties are retained. These improvements have enhanced the potential of nanosheet membranes in practical applications such as separation processes.
RESUMEN
Marine mussel inspired polydopamine (PDA) has received increased attention due to its good thermal and chemical stability as well as strong adhesion on most materials. In this work, high-performance nanofiltration membranes based on interpenetrating polymer networks (IPN) incorporating PDA and polybenzimidazole (PBI) were developed for organic solvent nanofiltration (OSN). Generally, in order to obtain solvent stability, polymers need to be covalently cross-linked under harsh conditions, which inevitably leads to losses in permeability and mechanical flexibility. Surprisingly, by in situ polymerization of dopamine within a PBI support, excellent solvent resistance and permeance of polar aprotic solvents were obtained without covalent cross-linking of the PBI backbone due to the formation of an IPN. The molecular weight cutoff and permeance of the membranes can be fine-tuned by changing the polymerization time. Robust membrane performance was achieved in conventional and emerging green polar aprotic solvents (PAS) in a wide temperature range covering -10 °C to +100 °C. It was successfully demonstrated that the in situ polymerization of PDA-creating an IPN-can provide a simple and green alternative to covalent cross-linking of membranes. To elucidate the nature of the solvent stability, a detailed analysis was performed that revealed that physical entanglement along with strong secondary interaction synergistically enable solvent resistance with as low as 1-3% PDA content.
RESUMEN
Amino functionalized boron nitride nanosheets (FBN) were incorporated into a crosslinked, thermally rearranged polyimide (XTR) to fabricate FBN-XTR nanocomposite membrane. The FBN-XTR membrane exhibited a small decrease in H2 permeability but demonstrated a remarkably increased H2 gas selectivity over other gases, compared with XTR. The XTR membrane heat-treated at 425 °C had a H2 permeability of 210 Barrers and a H2 /CH4 separation factor of 24.1, whereas the nanocomposite membrane with 1â wt % FBN exhibited a H2 permeability of 110 Barrers and H2 /CH4 separation factor of 275, an order of magnitude greater. At 1â wt % FBN loading, the FBN-XTR membrane showed three times higher tensile strength and 60 % higher elongation than pristine XTR membrane. In addition, FBN-XTR was found to be able to be readily processed into thin-film membranes for practical H2 separation applications.
RESUMEN
A fundamental understanding of polymer microstructure is important in order to design novel polymer electrolyte membranes (PEMs) with excellent electrochemical performance and stabilities. Hydrocarbon-based polymers have distinct microstructure according to their chemical structure. The ionic clusters and/or channels play a critical role in PEMs, affecting ion conductivity and water transport, especially at medium temperature and low relative humidity (RH). In addition, physical properties such as water uptake and dimensional swelling behavior depend strongly on polymer morphology. Over the past few decades, much research has focused on the synthetic development and microstructural characterization of hydrocarbon-based PEM materials. Furthermore, blends, composites, pressing, shear field, electrical field, surface modification, and cross-linking have also been shown to be effective approaches to obtain/maintain well-defined PEM microstructure. This review summarizes recent work on developments in advanced PEMs with various chemical structures and architecture and the resulting polymer microstructures and morphologies that arise for potential application in fuel cell, lithium ion battery, redox flow battery, actuators, and electrodialysis.
RESUMEN
It is well-known that solvent treatment and preconditioning play an important role in rejection and flux performance of membranes due to solvent-induced swelling and solvent adsorption. Investigations into the effect of solvent treatment are scarce and application specific, and were limited to a few solvents only. This study reveals the trend in solvent treatment based on solvent polarity in a systematic investigation with the aim to harness such effect for intensification of membrane processes. Nine solvents with polarity indices ranging from 0.1 to 5.8 (hexane to acetonitrile) were used as treatment and process solvents on commercial Borsig GMT-oNF-2, Evonik Duramem 300, and emerging tailor-made polybenzimidazole membranes. TGA-GCMS, HS-GC-FID, and NMR techniques were employed to better understand the effect of solvent treatment on the polymer matrix of membranes. In this work, apart from the solvent treatment's direct effect on the membrane performance, a subsequent indirect effect on the ultimate separation process was observed. Consequently, a pharmaceutical case study employing chlorhexidine disinfectant and antiseptic was used to demonstrate the effect of solvent treatment on the nanofiltration-based purification. It is shown that treatment of polybenzimidazole membranes with acetone resulted in a 25% increase in product recovery at 99% impurity removal. The cost of the process intensification is negligible in terms of solvent consumption, mass intensity, and processing time.
RESUMEN
In this work, three functional groups were introduced in poly(arylene ether sulfone) membranes to investigate the effects of cationic functional groups in the membranes on reverse electrodialysis performance. Our results showed that controlling the swelling behaviour of the membranes was an important factor for increasing the permselectivity while maintaining their high conductivity.
RESUMEN
Highly permeable, thermally rearranged polymer membranes based on bismaleimide derivatives that exhibit excellent CO2 permeability up to 5440 Barrer with a high BET surface area (1130 m2 g-1) are reported for the first time. In addition, the membranes can be easily used to form semi-interpenetrating networks with other polymers endowing them with superior gas transport properties.
RESUMEN
The regulation of water content in polymeric membranes is important in a number of applications, such as reverse electrodialysis and proton-exchange fuel-cell membranes. External thermal and water management systems add both mass and size to systems, and so intrinsic mechanisms of retaining water and maintaining ionic transport in such membranes are particularly important for applications where small system size is important. For example, in proton-exchange membrane fuel cells, where water retention in the membrane is crucial for efficient transport of hydrated ions, by operating the cells at higher temperatures without external humidification, the membrane is self-humidified with water generated by electrochemical reactions. Here we report an alternative solution that does not rely on external regulation of water supply or high temperatures. Water content in hydrocarbon polymer membranes is regulated through nanometre-scale cracks ('nanocracks') in a hydrophobic surface coating. These cracks work as nanoscale valves to retard water desorption and to maintain ion conductivity in the membrane on dehumidification. Hydrocarbon fuel-cell membranes with surface nanocrack coatings operated at intermediate temperatures show improved electrochemical performance, and coated reverse-electrodialysis membranes show enhanced ionic selectivity with low bulk resistance.