GIS and cellular automata based slope rainwater movement process model and its application.

Rainfall serves as a significant factor contributing to slope stability challenges in mountainous areas, and simulating the process of slope rainwater movement is a crucial approach for analyzing the stability of slopes triggered by rainfall. By combining computer numerical simulation technology with traditional hydraulic and hydrological calculation theories, it is possible to create an efficient and precise rainwater movement model that can simulate and analyze the process of rainwater movement on slopes. Utilizing natural slopes as the focal point of our research, the cellular automaton method was applied to simulate rainfall runoff on slopes, and a Cellular Automata (CA) based model for rainwater movement process was developed. This model modified the Green-Ampt (G-A) infiltration model by adopting an elliptical water content curve and introducing a coefficient that quantifies the ratio of saturated to unsaturated depth. Additionally, we refined the rules governing runoff generation and convergence within the slope and on its surface, enabling a comprehensive simulation of the entire rainwater movement process on the slope. Furthermore, the effectiveness of the model was validated through analytical solutions derived from simplified assumptions, laboratory experiments on infiltration and runoff in the flume, and a case study of a natural slope. The results show that the infiltration calculation results of the rainwater movement model are closer to the experimental values, and their overall values are slightly higher than the measured values, which are basically consistent with the model test results; The runoff calculation results show a phenomenon of initially increasing and gradually approaching the measured values compared to the measured values. When applying the model to an actual slope, it was found that the model comprehensively accounts for the influence of slope seepage, infiltration and runoff process, has better performance compared to G-A modified model. The model can be used to describe the spatial distribution and temporal variation of infiltration and runoff processes.

Generation of human induced pluripotent stem cell line from a patient with restrictive cardiomyopathy.

Restrictive cardiomyopathy (RCM) is a rare cardiomyopathy characterized by diastolic dysfunction, which affects cardiac systolic function. We successfully established human induced pluripotent stem cells (hiPSCs) from peripheral blood mononuclear cells of 24-year-old male with restrictive cardiomyopathy (RCM). The patient-derived hiPSCs carried heterozygous mutation of CRYAB gene (c.326A > G, p.D109G), which was consistent with clinical whole exon sequencing results. We confirmed the pluripotency, multipotential differentiation and karyotype of hiPSCs. The hiPSCs will be useful for studying the pathogenesis of RCM caused by CRYAB (c.326A > G) mutation.

The Role of Surface Defects in Photoluminescence and Decay Dynamics of High-Quality Perovskite MAPbI3 Single Crystals.

Halide perovskites have recently been a star semiconductor material in photovoltaic field owing to their excellent optoelectronic properties. An in-depth understanding of the photoluminescence and carrier diffusion in these materials may facilitate the implementation of high-performance optolelctronic devices. Here, we report an unusual photoluminescence quenching phenomenon in MAPbI3 single crystals. Interestingly, MAPbI3 single crystal with higher crystalline quality shows a lower photoluminescence emission and a shorter decay time, indicating the surface imperfection plays an important role to the photoluminescence. The quick quenching process is attributed to the synergistic effect of localized effect at the defects and rapid inward diffusion.

High-performance stretchable photodetector based on CH3NH3PbI3 microwires and graphene.

A stretchable photodetector was fabricated by releasing a prestrained 3 M very high bond (VHB) substrate coated with perovskite CH3NH3PbI3 microwires and graphene. The light harvesting CH3NH3PbI3 microwires were realized through a transformation from CH3NH3PbI3 bulk single crystals. Graphene served as an expressway for photoinduced carriers in the perovskite. Under a very low working voltage bias of 0.01 V and irradiance power of 13.5 mW cm-2 under 785 nm laser illumination, the responsivity could be as high as 2.2 mA W-1. When the device was stretched up to 30%, 50%, and 80% strain, the responsivity was maintained at 0.96, 0.60, and 0.21 mA W-1, respectively. It also showed a fast photoresponse (<0.12 s) after stretching to 10%, 30%, 50%, 80%, and even to 100%. The device performed well after 100 cycles of stretching to 50% strain.

Formic acid: an accelerator and quality promoter for nonseeded growth of CH3NH3PbI3 single crystals.

With the aid of formic acid, CH3NH3PbI3 single crystal of 9 mm in length was directly harvested within 3 days via a nonseeded solution temperature-lowering (STL) method. It showed a record-narrow full width at half maximum of 13 arcsec for the high-resolution X-ray rocking curve, a low trap-state density of 3.1 × 109 cm-3, a high carrier mobility of 162 cm2 V-1 s-1 and high moisture stability. The addition of formic acid could suppress the oxidation of iodide ions in a conventional STL process, resulting in rapid growth of high-quality CH3NH3PbI3 single crystals.

Perovskite CH3NH3PbI3(Cl) Single Crystals: Rapid Solution Growth, Unparalleled Crystalline Quality, and Low Trap Density toward 10(8) cm(-3).

Single crystal reflects the intrinsic physical properties of a material, and single crystals with high-crystalline quality are highly desired for the acquisition of high-performance devices. We found that large single crystals of perovskite CH3NH3PbI3(Cl) could be grown rapidly from chlorine-containing solutions. Within 5 days, CH3NH3PbI3(Cl) single crystal as large as 20 mm × 18 mm × 6 mm was harvested. As a most important index to evaluate the crystalline quality, the full width at half-maximum (fwhm) in the high-resolution X-ray rocking curve (HR-XRC) of as-grown CH3NH3PbI3(Cl) single crystal was measured as 20 arcsec, which is far superior to so far reported CH3NH3PbI3 single crystals (∼1338 arcsec). The unparalleled crystalline quality delivered a low trap-state density of down to 7.6 × 10(8) cm(-3), high carrier mobility of 167 ± 35 cm(2) V(-1) s(-1), and long transient photovoltaic carrier lifetime of 449 ± 76 µs. The improvement in the crystalline quality, together with the rapid growth rate and excellent carrier transport property, provides state-of-the-art single crystalline hybrid perovskite materials for high-performance optoelectronic devices.

High-Performance Planar-Type Photodetector on (100) Facet of MAPbI3 Single Crystal.

Recently, the discovery of organometallic halide perovskites provides promising routes for fabricating optoelectronic devices with low cost and high performance. Previous experimental studies of MAPbI3 optoelectronic devices, such as photodetectors and solar cells, are normally based on polycrystalline films. In this work, a high-performance planar-type photodetector fabricated on the (100) facet of a MAPbI3 single crystal is proposed. We demonstrate that MAPbI3 photodetector based on single crystal can perform much better than that on polycrystalline-film counterpart. The low trap density of MAPbI3 single crystal accounts for the higher carrier mobility and longer carrier diffusion length, resulted in a significant performance increasement of MAPbI3 photodetector. Compared with similar planar-type photodetectors based on MAPbI3 polycrystalline film, our MAPbI3 single crystal photodetector showed excellent performance with good stability and durability, broader response spectrum to near-infrared region, about 10(2) times higher responsivity and EQE, and approximately 10(3) times faster response speed. These results may pave the way for exploiting high-performance perovskites photodetectors based on single crystal.

Hexagonal crown-capped zinc oxide micro rods: hydrothermal growth and formation mechanism.

Hexagonal crown-capped ZnO micro rods were successfully prepared by a facile low-temperature hydrothermal method. The as-prepared ZnO micro rods are 4.4-5.2 µm in length and 2.4-3.6 µm in diameter, possessing a single-crystal hexagonal structure. The morphology evolution and structure changes were tracked during hydrothermal growth by field-emission scanning electron microscopy and X-ray diffraction, respectively. A three-stage growth mechanism of the hexagonal crown-capped ZnO micro rods was proposed and further verified by a growth solution renewal experiment. The room-temperature photoluminescence (PL) spectrum of the hexagonal crowns exhibits a strong UV emission at about 382 nm. The temperature dependent PL results indicate that the UV emission originates from the radiative free-exciton recombination.