Modification of traditional composite nonwovens with stable storage of light absorption transients and photodynamic antibacterial effect.

Combining photodynamic antimicrobials with nonwovens is prospective. However, common photosensitizers still have drawbacks such as poor photoactivity and the inability to charge. In this study, a photodynamic and high-efficiency antimicrobial protective material was prepared by grafting bis benzophenone-structured 4,4-terephthaloyl diphthalic anhydride (TDPA) photosensitizer, and antimicrobial agent chlorogenic acid (CA) onto spunbond-meltblown-spunbond (SMS) membranes. The charging rates for ·OH and H2O2 were 6377.89 and 913.52 µg/g/h. The light absorption transients structural storage remained above 69% for 1 month. High electrical capacity remained after seven cycles indicating its rechargeability and recyclability. The SMS/TDPA/CA membrane has excellent bactericidal performance when under illumination or lightless conditions, and the bactericidal efficiency of Escherichia coli and Staphylococcus aureus reached over 99%. The construction of self-disinfection textiles based on the photodynamic strategies proposed in this paper is constructive for expanding and promoting the application of textile materials in the medical field.

Photothermoelectric Synergistic Hydrovoltaic Effect: A Flexible Photothermoelectric Yarn Panel for Multiple Renewable-Energy Harvesting.

The human body is in a complex environment affected by body heat, light, and sweat, requiring the development of a wearable multifunctional textile for human utilization. Meanwhile, the traditional thermoelectric yarn is limited by expensive and scarce inorganic thermoelectric materials, which restricts the development of thermoelectric textiles. Therefore, in this paper, photothermoelectric yarns (PPDA-PPy-PEDOT/CuI) using organic poly(3,4-ethylenedioxythiophene) (PEDOT) and inorganic thermoelectric material cuprous iodide (CuI) are used for the thermoelectric layer and poly(pyrrole) (PPy) for the light-absorbing layer. With the introduction of PPy, the temperature difference of the photothermoelectric yarn can be increased for a better voltage output. Subsequently synergizing the photothermoelectric effect with the hydrovoltaic effect to create higher electric potentials, a single wet photothermoelectric yarn obtained by preparation can be irradiated under an infrared lamp at a voltage of up to 0.47 V. Finally, the photothermoelectric yarn PPDA-PPy-PEDOT/CuI was assembled in a series and parallel to obtain a photothermoelectric yarn panel, which was able to output 41.19 mV under an infrared lamp, and the synergistic photothermoelectric and hydrovoltaic effects of the photothermoelectric panel were tested outdoors on human body, and we found that the voltage was able to reach approximately 0.16 V under sunlight. Therefore, the voltage values obtained from the photothermoelectric yarns in this study are competitive and provide a new research idea for the study of photothermoelectric yarns.

Synthesis of scale-like nano-hydroxyapatite and preparation of biodegradable woven scaffolds for bone tissue engineering.

Bone tissue engineering scaffolds should have bone compatibility, biological activity, porosity, and degradability. In this study, flake-like hydroxyapatite was synthesized by hydrothermal method and mixed with sodium alginate to make a gel, which was injected into a hollow braid. Porous and degradable SA/n-Hap woven scaffolds were prepared by freeze-drying technology. The morphology of hydroxyapatite was characterized by scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR), and x-ray diffraction. The scaffolds were characterized by an improved liquid replacement method, compression test, and degradation test. The results showed that the hydroxyapatite synthesized at 160 °C had a scaly morphology. The prepared scaffold had a pore size of 5-100 µm, a porosity of 60%-70%, and a swelling rate of more than 300%. After 21 d the degradation rate reached 5.54%, and a cell survival rate of 214.98%. In summary, it is feasible to prepare porous bone scaffolds for potential bone tissue engineering. This study shows the feasibility of applying textile structures to the field of tissue scaffolds and provides a new idea for the application structure of tissue engineering scaffolds.

Flexible Puncture-Resistant Composites for Antistabbing Applications: Silica and Silicon Carbide Nanoparticle-/TPU-Coated Aramid Fabrics.

In harsh environments, it is crucial to design personal protective materials that possess both puncture/cut resistance and chemical resistance. In order to fulfill these requirements, this study introduces an innovative approach that combines hydrophobically modified rigid nanoparticles with thermoplastic polyurethane elastomers. These materials are then laminated with high-performance aramid fabrics through a scraping process, resulting in a multifunctional composite with puncture/cut resistance, superhydrophobicity, self-cleaning properties, and acid/alkali resistance. The quasi-static puncture tests conducted reveal the remarkable performance of the composite. The maximum spike puncture resistance reaches 267.62 N, which is 17.14 times higher than that of the pure fabric (15.61 N). Similarly, the maximum knife puncture resistance reaches 115.02 N, exhibiting a 5.01 times increase compared to that of the pure aramid fabric (22.97 N). Furthermore, the results obtained from the yarn pull-out, fabric burst strength, and tearing experiments demonstrate that the incorporation of rigid nanoparticles significantly enhances the friction between the yarns, enabling a greater number of yarns to participate in the dissipation of impact energy. As a result, the puncture resistance of the fabric is greatly improved. Significantly, the composite exhibits sustained superhydrophobicity even after exposure to harsh chemicals such as concentrated sulfuric acid and sodium hydroxide as well as undergoing cyclic mechanical wear. These findings highlight the composite's exceptional durability and resistance to corrosion. Overall, this study offers insights and methods for the development of multifunctional flexible puncture-resistant equipment for individuals.

Braided scaffolds with polypyrrole/polydopamine/hydroxyapatite coatings with electrical conductivity and osteogenic properties for bone tissue engineering.

When impaired bones are grafted with bone scaffolds, the behaviors of osteoblast are dependent on the implant materials and surface morphology. To this end, we modulated the surface morphology of scaffolds that promote cell growth. In this study, ice-template and spraying method methods are employed to coat different proportions of PDA and PPy over the PLA/PVA weaving scaffolds, after which HA is Coated over via the electrochemical deposition, forming weaving scaffolds with electrically conductive PDA/PPy/HA coating. The test results indicate that with a PPy/PDA concentration ratio is 30, the PPy particles are more uniformly distributed on the fiber surface. The scaffolds are wrapped in a HA coating layer with a high purity, and calcium and phosphorus elements are evenly dispersed with a Ca/P ratio being 1.69. Owing to the synergistic effect between PDA and PPy coating, the scaffolds demonstrate excellent electrochemical stability and electrochemical activity. The biological activity of the scaffold increased to 274.66% under electrical stimulation. The new thinking proposed by this study extends the worth of applying textile structure to the medical field, the application of which highly increases the prospect of bone tissue engineering.

Biomimetic helical fiber cellulose acetate/thermoplastic polyurethanes photodynamic antibacterial membrane: Synthesis, characterization, and antibacterial application.

This study designed a novel co-electrospun cellulose acetate (CA)/thermoplastic polyurethane (TPU) photodynamic helical fiber antibacterial membrane as a potential environmentally friendly medical protective material. A central combined design method (CCD) based on response surface methodology (RSM) was used to analyze essential variables' influence. The optimized parameters for CCD were TPU (wt%) 11.68 %, CA (wt%) 13.89 %, DMAc/ACE volume ratio 0.147, LiCl (wt%) 1.39 %, and voltage (kV) 14.43 V. Pitch and pitch diameter were the response process as the critical output variable. The membranes were characterized by SEM, TG, FT-IR, and molecular structure analysis. The results showed that the photodynamic helical fiber antimicrobial membrane exhibited synergistic effects of the antibacterial photodynamic therapy (APDT) and antimicrobial agent under average daylight irradiation. The release rate of -OH was 98.22 %, and H2O2 was 88.36 % under the action of 20 min of light. The bactericidal rates of S. aureus and E. coli reached 99.9 % and 99.7 %, respectively. The fiber helical structure can increase the light absorption rate, thus increasing the release rate and amount of reactive oxygen species (ROS) species, increasing the antibacterial rate. After washing five times, the antibacterial membrane has excellent antibacterial performance and a dark antibacterial effect.

A Study on Tencel/LMPET-TPU/Triclosan Laminated Membranes: Excellent Water Resistance and Antimicrobial Ability.

Medical product contamination has become a threatening issue against human health, which is the main reason why protective nonwoven fabrics have gained considerable attention. In the present, there is a soaring number of studies on establishing protection systems with nonwoven composites via needle punch. Meanwhile, the disadvantages of composites, such as poor mechanical performance and texture, impose restrictions. Hence, in this study, an eco-friendly method composed of needling, hot pressing, and lamination is applied to produce water-resistant, windproof, and antimicrobial Tencel/low-melting-point polyester-thermoplastic polyurethane/Triclosan (Tencel/LMPET-TPU/TCL) laminated membranes. Field-emission scanning electron microscope (SEM) images and FTIR show needle-punched Tencel/LMPET membranes successfully coated with TPU/TCL laminated membranes, thereby extensively improving nonwoven membranes in terms of water-resistant, windproof, and antimicrobial attributes. Parameters including needle punch depth, content of LMPET fibers, and concentration of TCL are changed during the production. Specifically, Tencel/LMPET-TPU/TCL-0.1 laminated nonwovens acquire good water resistance (100 kPa), outstanding windproof performance (<0.1 cm3/cm2/s), and good antimicrobial ability against Escherichia coli and Staphylococcus aureus. Made with a green production process that is pollution-free, the proposed products are windproof, water resistant, and antimicrobial, which ensures promising uses in the medical and protective textile fields.

Synergy of Adsorption and Photocatalytic Reduction for Efficient Removal of Cr(VI) with Polyvinylidene Fluoride@Polyvinyl Alcohol-FeC2O4/Bi2.15WO6.

Although the photocatalytic reduction of Cr(VI) to Cr(III) by traditional powder photocatalysts is a promising method, the difficulty and poor recovery of photocatalysts from water hinder their wide practical applications. Herein, we present that FeC2O4/Bi2.15WO6 (FeC2O4/BWO) composites were tightly bonded to modified polyvinylidene fluoride (PVDF) membranes by chemical grafting with the aid of polyvinyl alcohol (PVA) to form photocatalytic composite membranes (PVDF@PVA-FeC2O4/BWO). The contact angle of PVDF@PVA-FeC2O4/BWO (0.06 wt % of FeC2O4/BWO) is 48.0°, which is much lower than that of the pure PVDF membrane (80.5°). Meanwhile, the permeate flux of 61.43 g m-2 h-1 and water flux of 250.60 L m-2 h-1 were observed for PVDF@PVA-FeC2O4/BWO composite membranes. The tensile strength of composite membranes reached 48.84 MPa, which was 9.8 times higher than that of PVDF membrane. It was found that the PVDF@PVA-FeC2O4/BWO membrane exhibited excellent photocatalytic Cr(VI) reduction performance under both simulated and real sunlight irradiation. The adsorption for Cr(VI) by PVDF@PVA-FeC2O4/BWO can reach 47.6% in the dark process within 30 min, and the removal percentage of Cr(VI) could reach 100% with a rate constant k value of 0.2651 min-1 after 10 min of light exposure, indicating a synergistic effect of adsorption and photoreduction for Cr(VI) removal by the composite membrane. The PVDF@PVA-FeC2O4/BWO membrane had good stability and reusability after seven consecutive cycles. Most importantly, the influences of foreign ions on Cr(VI) reduction were investigated to mimic real sewage, which revealed that no obvious adverse effects can be found with the presence of common foreign ions in sewage. The photocatalytic membrane material developed in this study provides a new idea for treating Cr(VI)-containing wastewater and has a more significant application prospect.

Oriented ascorbic acid onto zeolitic metal-organic framework-8 membrane via microfluidic spinning for biomedical care.

Nowadays, the hydrogen dressing and electrostatic spun films widely used on wounds do not facilitate the permeability of the wound area and fail to achieve controlled drug delivery. Therefore, finding a wound dressing with both breathability and targeted drug delivery has remained an unmet challenge. Here, an oriented microstructure membrane with sustained drug release and robust antibacterial performance was constructed through the microfluidic spinning method. The multifunctional oriented membrane was prepared by loading ascorbic acid onto the zeolitic metal-organic framework-8 to develop drug delivery nanomaterial zeolitic metal-organic framework-8 @ascorbic acid (ZIF-8 @AA) and then mixing ZIF-8 @AA with polyvinyl pyrrolidone (PVP) solution via microfluidic technology, which produced an oriented microfiber member. In addition, the spinning parameters, including the fluid content, rotation speed, and flow rate, on microfiber diameter were evaluated. The constructed oriented membrane had bactericidal efficiencies of 82.94% ± 2.79% and 95.96% ± 1.54% against E. coli and S. aureus, respectively. After five days, the membrane still has a sustained release. Moreover, the fabricated membrane also has good biocompatibility and hemocompatibility in vitro. The oriented arrangement strategy provides a promising approach for wound healing materials in targeted drug delivery. Furthermore, this strategy offers a feasible idea for loading active materials into substrates for disease treatment in the biomedical field.

Antibacterial Surgical Sutures Developed Using Electrostatic Yarn Wrapping Technology.

A significant amount of research has been conducted on applying functional materials as surgical sutures. Therefore, research on how to solve the shortcomings of surgical sutures through available materials has been given increasing attention. In this study, hydroxypropyl cellulose (HPC)/PVP/zinc acetate nanofibers were coated on absorbable collagen sutures using an electrostatic yarn winding technique. The metal disk of an electrostatic yarn spinning machine gathers nanofibers between two needles with positive and negative charges. By adjusting the positive and negative voltage, the liquid in the spinneret is stretched into fibers. The selected materials are toxicity free and have high biocompatibility. Test results indicate that the nanofiber membrane comprises evenly formed nanofibers despite the presence of zinc acetate. In addition, zinc acetate can effectively kill 99.9% of E. coli and S. aureus. Cell assay results indicate that HPC/PVP/Zn nanofiber membranes are not toxic; moreover, they improve cell adhesion, suggesting that the absorbable collagen surgical suture is profoundly wrapped in a nanofiber membrane that exerts antibacterial efficacy and reduces inflammation, thus providing a suitable environment for cell growth. The employment of electrostatic yarn wrapping technology is proven effective in providing surgical sutures with antibacterial efficacy and a more flexible range of functions.

Long-Lasting Electret Melt-Blown Nonwoven Functional Filters Made of Organic/Inorganixc Macromolecular Micron Materials: Manufacturing Techniques and Property Evaluations.

Melt-blown nonwoven fabrics for filtration are usually manufactured using polypropylene, but after a certain time period the middle layer of the mask may have a reduced effect on adsorbing particles and may not be easily stored. Adding electret materials not only increases storage time, but also shows in this study that the addition of electret can improve filtration efficiency. Therefore, this experiment uses a melt-blown method to prepare a nonwoven layer, and adds MMT, CNT, and TiO2 electret materials to it for experiments. Polypropylene (PP) chip, montmorillonite (MMT) and titanium dioxide (TiO2) powders, and carbon nanotube (CNT) are blended and made into compound masterbatch pellets using a single-screw extruder. The resulting compound pellets thus contain different combinations of PP, MMT, TiO2, and CNT. Next, a hot pressor is used to make the compound chips into a high-poly film, which is then measured with differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR). The optimal parameters are yielded and employed to form the PP/MMT/TiO2 nonwoven fabrics and PP/MMT/CNT nonwoven fabrics. The basis weight, thickness, diameter, pore size, fiber covering ratio, air permeability, and tensile property of different nonwoven fabrics are evaluated in order to have the optimal group of PP-based melt-blown nonwoven fabrics. According to the results of DSC and FTIR measurements, PP and MMT, CNT, and TiO2 are completely mixed, and the melting temperature (Tm), crystallization temperature (Tc) and endotherm area are changed accordingly. The difference in enthalpy of melting changes the crystallization of PP pellets, which in turn changes the fibers. Moreover, the Fourier transform infrared (FTIR) spectroscopy results substantiate that PP pellets are well blended with CNT and MMT, according to the comparisons of characteristic peaks. Finally, the scanning electron microscopy (SEM) observation suggests that with a spinning die temperature of 240 °C and a spinning die pressure lower than 0.01 MPa, the compound pellets can be successfully formed into melt-blown nonwoven fabrics with a 10-micrometer diameter. The proposed melt-blown nonwoven fabrics can be processed with electret to form long-lasting electret melt-blown nonwoven filters.

Coaxial microfluidic spinning design produced high strength alginate membranes for antibacterial activity and drug release.

Directional drug delivery and sufficient strength are two conditions that need to be met for wound dressing. In this paper, an oriented fibrous alginate membrane with sufficient strength was constructed via coaxial microfluidic spinning, and zeolitic imidazolate framework-8/ascorbic acid was used to realize drug delivery and antibacterial activity. The effects of the process parameters of the coaxial microfluidic spinning on the mechanical properties of the alginate membrane were discussed. In addition, it was found that the antimicrobial activity mechanism of zeolitic imidazolate framework-8 was attributed to the disruptive effect of reactive oxygen species (ROS) on bacteria, and the quantitative amount of generated ROS were evaluated by detecting •OH and H2O2. Furthermore, a mathematical drug diffusion model was established and showed high consistency with the experimental data (R2 = 0.99). This study provides a new idea for the preparation of dressing materials with high strength and directional drug delivery and also provides some guidance for the development of coaxial microfluidic spin technology to be used in functional materials for drug release.

A sustainable layered nanofiber/sheet aerogels enabling repeated life cycles for effective oil/water separation.

Discarded oil-containing absorbents, which has been used in handling oil spills, are tricky to deal with and have rose global environmental concerns regarding release of microplastics. Herein, we developed a facile strategy to fabricate sustainable absorbents by a gas-inflating method, through which 2D electrospinning polycaprolactone nanofiber membranes were directly inflated into highly porous 3D nanofiber/sheet aerogels with layered long fiber structure. The membranes were inflated rapidly from a baseline porosity of 81.98% into 97.36-99.42% in 10-60 min. The obtained aerogels were further wrapped with -CH3 ended siloxane structures using CH3SiCl3. This hydrophobic absorbent (CA ≈ 145°) could rapidly trap oils from water with sorption range of 25.60-42.13 g/g and be recycled by simple squeeze due to its mechanical robustness. As-prepared aerogels also showed high separation efficiency to separate oils from both oil/water mixtures and oil-in-water emulsions (>96.4%). Interestingly, the oil-loaded absorbent after cleaning with absolute ethanol could be re-dissolved in selected solvents and promptly reconstituted by re-electrospinning and gas-inflation. The reconstituted aerogels were used as fire-new oil absorbents for repeated life cycles. The novel design, low cost and sustainability of the absorbent provides an efficient and environmentally-friendly solution for handling oil spills.

Biomass Chitosan-Based Tubular/Sheet Superhydrophobic Aerogels Enable Efficient Oil/Water Separation.

Water pollution, which is caused by leakage of oily substances, has been recognized as one of the most serious global environmental pollutions endangering the ecosystem. High-quality porous materials with superwettability, which are typically constructed in the form of aerogels, hold huge potential in the field of adsorption and removal of oily substances form water. Herein, we developed a facile strategy to fabricate a novel biomass absorbent with a layered tubular/sheet structure for efficient oil/water separation. The aerogels were fabricated by assembling hollow poplar catkin fiber into chitosan sheets using a directional freeze-drying method. The obtained aerogels were further wrapped with -CH3-ended siloxane structures using CH3SiCl3. This superhydrophobic aerogel (CA ≈ 154 ± 0.4°) could rapidly trap and remove oils from water with a large sorption range of 33.06-73.22 g/g. The aerogel facilitated stable oil recovery (90.07-92.34%) by squeezing after 10 sorption-desorption cycles because of its mechanical robustness (91.76% strain remaining after 50 compress-release cycles). The novel design, low cost, and sustainability of the aerogel provide an efficient and environmentally friendly solution for handling oil spills.

Construction Sheets Made of High-Performance Flame-Retardant Nonwoven Fabrics and Combustion-Resistant Polyurethane Foam: Preparation Process and Property Evaluations.

In this study, nonwoven fabrics, rigid polyurethane foam (RPUF), Basalt woven fabrics, and an aluminum foil film mold are used to produce multi-functional composite sheets with flame-retardant, sound-absorbing, and electromagnetic-shielding functions. The nonwoven layer is composed of Nomex fibers, flame-retardant PET fibers, and low-melting-point (LMPET) fibers via the needle rolling process. The optimal Nomex fiber/flame-retardant PET fiber/LMPET fiber (N/F/L) nonwoven fabrics are then combined with rigid polyurethane (PU) foam, Basalt woven fabric, and an aluminum foil film mold, thereby producing nonwoven/rigid polyurethane foam/Basalt woven fabric composite sheets that are wrapped in the aluminized foil film. The test results indicate that formed with a foaming density of 60 kg/m3 and 10 wt% of a flame retardant, the composite sheets exhibit electromagnetic interference shielding efficacy (EMI SE) that exceeds 40 dB and limiting oxygen index (LOI) that is greater than 26. The efficient and highly reproducible experimental design proposed in this study can produce multifunctional composite sheets that feature excellent combustion resistance, sound absorption, and EMI SE and are suitable for use in the transportation, industrial factories, and building wall fields.

Thermoplastic Laminated Composites Applied to Impact Resistant Protective Gear: Structural Design and Development.

Laminated composites have been commonly applied to all fields. When made into laminated composites, Kevlar woven fabrics are able to provide the required functions. In this study, two types of TPU are incorporated to improve the intralayer features of Kevlar/TPU laminated composites. Hence, the Kevlar/TPU laminated composites consist of firmly bonded laminates while retaining flexibility of the fabrics. Being the interlayer of the laminated composites, the TPU layer provides adhesion while strengthening the tensile property, dynamic puncture resistance, and buffer strength of Kevlar/TPU laminated composites. The test results indicate that with a blending ratio of two types of TRU being 85/15 wt%, the Kevlar/TPU laminated composites exhibit a tensile strength of 18.08 MPa. When the stacking thickness is 1 mm, the tensile strength is improved to 357.73 N with the buffering strength reaching 4224.40 N. Notably, with a thickness being 1.2 mm, the laminated composites demonstrate a dynamic resistance being 672.15 N. In the meanwhile, functional Kevlar fabrics are allowed to keep the fiber morphology owing to the protection of TPU composite films. Considering the composition of protective gear, Kevlar/TPU laminated composites possess a powerful potential and are worthwhile exploring.

Combing High-Modulus Fibers with a Novel Foaming Structure Applied to Protective Sandwich-Structured Composites: Manufacturing Techniques and Property Evaluations.

This study proposes the composites with a sandwich structure that is primarily made by the multi-step foaming process. The staple material is polyurethane (PU) foam that is combined with carbon fibers, followed by a Kevlar woven fabric. The composites are evaluated in terms of puncture resistance, buffer absorption, and electromagnetic wave shielding effectiveness (EMSE). The manufacturing process provides the composites with a stabilized structure efficiently. Serving the interlayer, a Kevlar woven fabric are sealed between a top and a bottom layer consisting of both PU foam and an aluminum film in order, thereby forming five-layered composites. Namely, the upper and lower surfaces of the five-layered sandwiches are aluminum films which is laminated on a purpose for the EMSE reinforcement. The test results indicate that the PU foam composites are well bonded and thus acquire multiple functions from the constituent materials, including buffer absorption, puncture resistance, and EMSE. There is much prospect that the PU foam composites can be used as a protective material in diverse fields owing to a flexible range of functions.

Photothermal and Concus Finn capillary assisted superhydrophobic fibrous network enabling instant viscous oil transport for crude oil cleanup.

Rapid and effective removal of highly viscous oil spills from the sea remains a great challenge globally. Superhydrophobic materials are attractive candidates for handling oil spills, but they are restrained to recover oils with low viscosity exclusively. Herein, we report a novel polypyrrole wrapped superhydrophobic fibrous network using cross-shaped polyester fibers as starting blocks. The polypyrrole coating enables the absorbent to convert light to heat, ensuring that the viscosity of heavy oils in the proximity can be easily controlled. In the meanwhile, the special structure of the starting fibers initiates Concus Finn (CFin) capillary allowing instant oil transport in the network. When the absorbent is exposed to light oils (0-500 mPa.s), the oils can be transported instantly via CFin capillary. Interestingly, under synergistic effect of light-to-heat conversion and CFin capillary, a drawing-sticking crude oil strip (105 mPa.s) is sucked instantly against gravity by the absorbent. The absorbent is successfully applied to efficiently separate both oil/water mixtures and oil/water emulsions (efficiency > 99%). Such absorbent can absorb 62.99-74.23 g/g light oils on average and up to 123.3 g/g crude oil under 0-2 sun illumination, holding a huge potential in managing oil spills.

Enhancing mechanical and photocatalytic properties by surface microstructure regulation of TiO2 nanofiber membranes.

In this work, TiO2 nanofiber membrane (NFM) with a complete surface microstructure was prepared through regulating the surface microstructure of TiO2 NFM by doping Zr. The crystal structures and morphological analyses indicated that the nanofiber membranes were consisted by disordered accumulation of Zr-doped TiO2 nanofibers with a crack-free surface, small grain size and high aspect ratio. When the doping amount of Zr was 0.8 mL, the tensile strength of the doped membranes reached 1.27 MPa, which was 60.7% higher than that of pure TiO2 NFM. The photocatalytic performance of Zr-doped TiO2 NFM was evaluated by the degradation performance of Methylene orange (MO) under simulated sunlight irradiation. Compared with the undoped TiO2 NFM, the 0.8-Zr/TiO2 NFM presented a higher catalytic degradation efficiency (improved by 69.6%), and the photocatalytic performance maintained stable after five circulating. It was found that the doping of Zr ions effectively limited the surface crack size and grain size of TiO2 nanofibers, thereby improving the tensile strength, and enhanced the surface area effect and carrier transfer efficiency of TiO2 NFM. On the other hand, a narrow band-gap was obtained by doping a small amount of Zr ions, which expanded the visible light response range to improve the photocatalytic performance of TiO2 nanofibers.

A two-step strategy to deposit a hydroxyapatite coating on polydopamine-coated polymer fibers.

As the main inorganic component of human bones and teeth, hydroxyapatite (HA), with excellent bioactivity and biocompatibility, shows great potential in the bone tissue engineering field. Marine mussel-inspired polydopamine (PDA) possesses unique functional groups and thus can absorb the calcium ions from extracellular fluid, thereby triggering the precipitation of HA. This study is based on a two-step strategy. Using the chemical activity of PDA, polyvinyl alcohol/polylactic acid (PVA/PLA) braids were coated with a PDA layer that served as a template for the electrochemical deposition of a HA layer. The test results indicate that the resulting HA crystals were assembled on the polymer fibers in an urchin-like mannerwith a stratified structure. Subsequently, the HA/PDA-PVA/PLA braided bone scaffolds were immersed in simulated body fluid for ten days, after which the bone scaffolds were found to be completely coated with HA, indicating a good biomineralization capability. Cell activity of HA/PDA-PVA/PLA scaffolded by dopamine-assisted electrodeposition was 178.8% than that of PVA/PLA braids. This HA coating layer inspired by biochemical strategies may be useful in the field of bone tissue engineering.