Rapid removal of trace haloacetic acids from drinking water by a continuous adsorption process using graphene oxide.

Significant health risks are caused by trace levels of haloacetic acids (HAAs) in drinking water. We used graphene oxide (GO), a high-performance absorbent, to remove monochloroacetic acid (MCAA), dichloroacetic acid (DCAA) and trichloroacetic acid (TCAA). 31.6%, 27.1% and 30.2% of MCAA, DCAA and TCAA in drinking water could be rapidly removed within 2 min by the interaction of intermolecular hydrogen bonds between GO and HAAs. On the other hand, as a type of weak interaction, intermolecular hydrogen bonds are easy to fracture, which leads to the recovery of GO. The removal efficiency of MCAA, DCAA and TCAA monotonously decreased with increasing pH from 3 to 11. Temperature was not an important influence on the removal efficiency of HAAs, and only affected the interaction of intermolecular hydrogen bonds between GO and HAAs. A continuous adsorption process was used for further improving the removal efficiency of HAAs, and the concentration of total HAAs decreased from 436 to 52.5 µg L-1 after five adsorption processes. The total contact time was just 2.25 min, which was faster than other reported adsorbents, and total HAAs could be decreased by 88%. The innovative process in this study provides an effective method for application of GO to rapidly remove HAAs in drinking water.

Adsorption of Trace Estrogens in Ultrapure and Wastewater Treatment Plant Effluent by Magnetic Graphene Oxide.

In the current study, graphene oxide, Fe3+, and Fe2+ were used for the synthesis of magnetic graphene oxide (MGO) by an in situ chemical coprecipitation method. Scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, and X-ray diffraction were used to characterize the well-prepared MGO. The prepared MGO was used as an adsorbent to remove five typical estrogens (estrone (E1), 17β-estradiol (E2), 17α-ethinylestradiol (17α-E2), estriol (E3), and synthetic estrogen (EE2)) at the ppb level from spiked ultrapure water and wastewater treatment plant effluent. The results indicated that the MGO can efficiently remove estrogens from both spiked ultrapure water and wastewater treatment plant effluent in 30 min at wide pH ranges from 3 to 11. The temperature could significantly affect removal performance. A removal efficiency of more than 90% was obtained at 35 °C in just 5 min, but at least 60 min was needed to get the same removal efficiency at 5 °C. In addition, an average of almost 80% of the estrogens can still be removed after 5 cycles of MGO regeneration but less than 40% can be reached after 10 cycles. These results indicate that MGO has potential for practical applications to remove lower levels of estrogens from real water matrixes and merits further evaluation.

Occurrence and formation potential of nitrosamines in river water and ground water along the Songhua River, China.

The presence of mutagenic and carcinogenic nitrosamines in water is of great concern. In this study, seven nitrosamines including N-nitrosodimethylamine (NDMA), N-nitrosodiethylamine (NDEA), N-nitrosomethylethylamine (NMEA), N-nitrosopyrrolidine (NPyr), N-nitrosopiperidine (NPip), N-nitrosodi-n-propylamine (NDPA), and N-nitrosodi-n-butyl-amine (NDBA) were investigated in river water and ground water samples collected from 5 representative cities (Jilin, Songyuan, Harbin, Jiamusi and Tongjiang) along the Songhua River. The total concentrations of nitrosamines in ground water were n.d. (not detected) to 60.8ng/L, NDMA was the most frequently detected nitrosamines in ground water, followed by NDEA and NPip. Relatively high detected frequency and concentrations of NDMA were also observed in river water samples, and the total nitrosamines' concentration at midstream is always higher than that at upstream and downstream. After 24hr chlorination, concentration of NDMA, NDBA was obviously increased but NDEA was reduced. Furthermore, UV254 showed a better relationship with NDMA-FP rather than dissolved organic carbon (DOC), NH4-N, and TDN.

Removing of Disinfection By-Product Precursors from Surface Water by Using Magnetic Graphene Oxide.

The magnetic graphene oxide (MGO) was successfully synthesised by the in situ chemical co-precipitation method with Fe3+, Fe2+ and graphene oxide (GO) in laboratory and, was used as an adsorbent for disinfection by-product (DBP) precursors removing from four natural surface water samples. The results indicate that various DBPs formation significantly decreased by 7-19% to 78-98% for the four samples after MGO treatment and, the treatment process was rapidly reached equilibrium within 20 minutes. The DBP precursors removal efficiency decreased with the increasing pH value from 4 to 10. Hydrophobic compounds (humic acid and fulvic acid) are more sensitive to MGO, whereas hydrophilic and nitrogenous compounds (aromatic proteins) are more insensitive. MGO could be regenerated by using 20% (v/v) ethanol and, the DBP precursors removal efficiency can stay stable after five cycles. These results indicate that MGO can be utilized as a promising adsorbent for the removal of DBP precursors from natural surface water.

Removing Phosphorus from Aqueous Solutions Using Lanthanum Modified Pine Needles.

The renewable pine needles was used as an adsorbent to remove phosphorus from aqueous solutions. Using batch experiments, pine needles pretreated with alkali-isopropanol (AI) failed to effectively remove phosphorus, while pine needles modified with lanthanum hydroxide (LH) showed relatively high removal efficiency. LH pine needles were effective at a wide pH ranges, with the highest removal efficiency reaching approximately 85% at a pH of 3. The removal efficiency was kept above 65% using 10 mg/L phosphorus solutions at desired pH values. There was no apparent significant competitive behavior between co-existing anions of sulfate, nitrate, and chloride (SO4(2-), NO3(-) and Cl(-)); however, CO3(2-) exhibited increased interfering behavior as concentrations increased. An intraparticle diffusion model showed that the adsorption process occurred in three phases, suggesting that a boundary layer adsorption phenomena slightly affected the adsorption process, and that intraparticle diffusion was dominant. The adsorption process was thermodynamically unfavorable and non-spontaneous; temperature increases improved phosphorus removal. Total organic carbon (TOC) assays indicated that chemical modification reduced the release of soluble organic compounds from 135.6 mg/L to 7.76 mg/L. This new information about adsorption performances provides valuable information, and can inform future technological applications designed to remove phosphorus from aqueous solutions.

Study of phosphate removal from aqueous solution by zinc oxide.

Zinc oxide (ZnO) was synthesized and used to investigate the mechanism of phosphate removal from aqueous solution. ZnO particles were characterized by X-ray diffraction, scanning electron microscope and Fourier transform infrared spectroscopy before and after adsorption. Batch experiments were carried out to investigate the kinetics, isotherms, effects of initial pH and co-existing anions. The adsorption process was rapid and equilibrium was almost reached within 150 min. The adsorption kinetics were described well by a pseudo-second-order equation, and the maximum phosphate adsorption capacity was 163.4 mg/g at 298 K and pH ∼6.2±0.1. Thermodynamic analysis indicated the phosphate adsorption onto ZnO was endothermic and spontaneous. The point of zero charge of ZnO was around 8.4 according to the pH-drift method. Phosphate adsorption capacity reduced with the increasing initial solution pH values. The ligand exchange and Lewis acid-base interaction dominated the adsorption process in the lower and the higher pH range, respectively. Nitrate, sulfate and chloride ions had a negligible effect on phosphate removal, while carbonate displayed significant inhibition behavior.

Application of ultrasound and quartz sand for the removal of disinfection byproducts from drinking water.

To the best of our knowledge, little information is available on the combined use of ultrasound (US) and quartz sand (QS) in the removal of disinfection byproducts (DBPs) from drinking water. This study investigates the removal efficiency for 12 DBPs from drinking water by 20 kHz sonolytic treatment, QS adsorption, and their combination. Results indicate that DBPs with logKow≤1.12 could not be sonolysized; for logKow≥1.97, more than 20% removal efficiency was observed, but the removal efficiency was unrelated to logKow. DBPs containing a nitro group are more sensitive to US than those that comprise nitrile, hydrogen, and hydroxyl groups. Among the 12 investigated DBPs, 9 could be adsorbed by QS adsorption. The adsorption efficiency ranged from 12% for 1,1-dichloro-2-propanone to 80% for trichloroacetonitrile. A synergistic effect was found between the US and QS on DBPs removal, and all the 12 DBPs could be effectively removed by the combined use of US and QS. In the presence of US, part of the QS particles were corroded into small particles which play a role in increasing the number of cavitation bubbles and reducing cavitation bubble size and then improve the removal efficiency of DBPs. On the other hand, the presence of US enhances the DBP mass transfer rate to cavitation bubbles and quartz sand. In addition, sonolytic treatment led to a slight decrease of pH, and TOC values decreased under all the three treatment processes.