Thermo-growing ion clusters enabled healing strengthening and tough adhesion for highly reliable skin electronics.

Self-healing and self-adhesion capacities are essential for many modern applications such as skin-interfaced electronics for improving longevity and reliability. However, the self-healing efficiency and adhesive toughness of most synthetic polymers are limited to their original network, making reliability under dynamic deformation still challenging. Herein, inspired by the growth of living organisms, a highly stretchable supramolecular elastomer based on thermo-responsive ion clusters and a dynamic polysulfide backbone was developed. Attributed to the synergic growth of ion clusters and dynamic exchange of disulfide bonds, the elastomer exhibited unique healing strengthening (healing efficiency >200%) and thermo-enhanced tough adhesion (interfacial toughness >500 J m-2) performances. To prove its practical application in highly reliable skin electronics, we further composited the elastomer with a zwitterion to prepare a highly conductive ionic elastomer and applied it in wearable strain sensing and long-term electrophysiological detection. This work provides a new avenue to realize high reliability in skin interfaced electronics.

Efficient Nanocrystal Photovoltaics with PTAA as Hole Transport Layer.

The power conversion efficiency (PCE) of solution-processed CdTe nanocrystals (NCs) solar cells has been significantly promoted in recent years due to the optimization of device design by advanced interface engineering techniques. However, further development of CdTe NC solar cells is still limited by the low open-circuit voltage (Voc) (mostly in range of 0.5-0.7 V), which is mainly attributed to the charge recombination at the CdTe/electrode interface. Herein, we demonstrate a high-efficiency CdTe NCs solar cell by using organic polymer poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine] (PTAA) as the hole transport layer (HTL) to decrease the interface recombination and enhance the Voc. The solar cell with the architecture of ITO/ZnO/CdS/CdSe/CdTe/PTAA/Au was fabricated via a layer-by-layer solution process. Experimental results show that PTAA offers better back contact for reducing interface resistance than the device without HTL. It is found that a dipole layer is produced between the CdTe NC thin film and the back contact electrode; thus the built-in electric field (Vbi) is reinforced, allowing more efficient carrier separation. By introducing the PTAA HTL in the device, the open-circuit voltage, short-circuit current density and the fill factor are simultaneously improved, leading to a high PCE of 6.95%, which is increased by 30% compared to that of the control device without HTL (5.3%). This work suggests that the widely used PTAA is preferred as the excellent HTL for achieving highly efficient CdTe NC solar cells.

Topologically Enhanced Dual-Network Hydrogels with Rapid Recovery for Low-Hysteresis, Self-Adhesive Epidemic Electronics.

Dual-network conductive hydrogels have drawn wide attention in epidemic electronics such as epidemic sensors and electrodes because of their inherent low Young's modulus, high skin-compliance, and tunable mechanical strength. However, it is still full of challenges to gain a dual-network hydrogel with high stretchability, low hysteresis, and skin-adhesive performance simultaneously. Herein, to address this issue, a novel dual-network hydrogel (denoted as PAa hydrogel) with polyacrylamide as the first network and topologically entangled polydopamine as the secondary network was prepared through a facile gel-phase in situ self-polymerization and soaking treatment. Benefiting from the topological enhancement as well as the synergetic effects of hydrogen bonds and metal coordination bonds, low modulus (∼10 kPa), excellent stretchability (1090.8%), high compression (90%), negligible hysteresis (η = 0.019, energy loss coefficient), rapid recovery in seconds, and self-adhesion are obtained in the PAa hydrogels. To demonstrate their practical use, a states-independent and skin-adhesive epidemic sensor was successfully attached on human skin for motion detection. What is more, by using the hydrogel as an epidemic electrode, electromyogram signals were accurately detected and wirelessly transmitted to a smart phone. This work offers a new insight to understand the strengthening mechanism of dual network hydrogels and a design strategy for both epidemic sensors and electrodes.

Hole Transfer Layer Engineering for CdTe Nanocrystal Photovoltaics with Improved Efficiency.

Interface engineering has led to significant progress in solution-processed CdTe nanocrystal (NC) solar cells in recent years. High performance solar cells can be fabricated by introducing a hole transfer layer (HTL) between CdTe and a back contact electrode to reduce carrier recombination by forming interfacial dipole effect at the interface. Here, we report the usage of a commercial product 2,2',7,7'-tetrakis[N,N-di(4-methoxyphenyl)amino]-9,9'-spirobifluorene (Spiro) as a hole transfer layer to facilitate the hole collecting for CdTe nanocrystal solar cells. It is found that heat treatment on the hole transfer layer has significant influence on the NC solar cells performance. The Jsc, Voc, and power conversion efficiency (PCE) of NC solar cells are simultaneously increased due to the decreased contact resistance and enhanced built-in electric field. We demonstrate solar cells that achieve a high PCE of 8.34% for solution-processed CdTe NC solar cells with an inverted structure by further optimizing the HTL annealing temperature, which is among the highest value in CdTe NC solar cells with the inverted structure.