Assessment of internal porosities for different placement techniques of bulk-fill resin-based composites: a micro-computed tomography study.

OBJECTIVES: The aim was to compare the porosity of different bulk-fill resin-based composites (RBCs) placement techniques to the conventional incremental technique using microcomputed tomography (µ-CT). MATERIAL AND METHODS: Occlusal cavities were prepared on extracted human molars, divided into five groups based on the placement technique (n = 10/group). Techniques examined were Monoblock-two-step (SureFil SDR flow + Ceram.X), Monoblock-two-step (Tetric EvoFlow Bulk-Fill + Tetric EvoCeram Bulk-Fill), Monoblock-one-step (Tetric EvoCeram Bulk-Fill), Monoblock with sonic activation (SonicFill2), and incremental technique (Filtek Z250). µ-CT scanning (SkyScan, Bruker, Belgium) assessed the number, volume of closed pores, and total porosity. Analysis of variance on ranks was used (Student-Newman-Keuls method and Mann-Whitney rank-sum test), to determine the significance of RBC viscosity and the sonication placement technique. The Spearman correlation method assessed the correlation between porosity characteristics (α = 0.05). RESULTS: The SonicFill2 presented a higher number of closed pores than the other groups (p < 0.05). The overall porosity within the restoration seemed greater in this order: Filtek Z250 > SonicFill2 > Tetric EvoFlow Bulk-Fill + Tetric EvoCeram Bulk-Fill > Tetric EvoCeram Bulk-Fill > SureFil SDR Flow + Ceram.X. Sonication was associated with increased number (p = 0.005) and volume (p = 0.036) of closed pores. A strong correlation was observed between the number and volume of closed pores (R2 = 0.549, p < 001). CONCLUSIONS: The monoblock technique with sonic activation showed significantly more internal porosity than the other placement techniques. Sonication during application contributed to the higher number and volume of closed pores than the passive bulk-fill application. CLINICAL RELEVANCE: Using bulk-fill materials enhances efficiency, yet void formation remains an issue, depending on viscosity and active/passive delivery of materials. Clinicians must familiarize themselves with effective placement techniques to reduce void formation and optimizing treatment outcomes.

Denture cleanser effect on resilient liners with distinct optical characteristics.

PURPOSE: To evaluate denture cleansing solutions regarding the surface roughness and color stability of two resilient liners with distinct optical characteristics used for the maximum recommended period of use. METHODS: The specimens of each resilient liner, transparent and white, were randomly distributed into groups (n= 15) of a daily 20-minute immersion simulation of 0.25%, 0.5% and 1% sodium hypochlorite (SH) and 4% acetic acid solutions. Surface roughness (Ra) and color stability (ΔE CIELab formula and NBS systems) were measured after 7, 14, 21, 30, 60, 90, 180, and 270 days. The factors of variations analyzed were material, solutions, and time of immersion. Statistical analysis used three-way ANOVA and Tukey tests (Ra), and repeated measure ANOVA (ΔE and NBS systems), P< 0.05. RESULTS: For Ra analysis, the variations occurred regardless of time and solution, as the white liner showed the greatest changes (P< 0.001). Regarding interactions between solution and time, in the period of 21 days until 270 days, Ra was equivalent for all solutions (P= 0.001). ΔE analysis showed a difference between solutions (P= 0.000) and interaction between time and solution (P= 0.000). For the transparent liner, the greatest changes were found for 1% SH after 60 days, however, at 270 days there was a color change equivalence with 0.5% SH, while 4% acetic acid solution showed intermediate values. For the white liner, 1% SH showed the highest color changes for all evaluated times, and the other evaluated solutions were similar after 270 days. For both resilient liners, 0.25% SH showed the smallest changes for the evaluated properties. CLINICAL SIGNIFICANCE: The changes found were dependent on the concentration of the solution used, as well as the length of exposure to the solution. In addition, the white resilient liner showed to be less susceptible to color changes. For both resilient liners, 0.25% sodium hypochlorite showed the least changes for the evaluated properties.

Effects of aging and light-curing unit type on the volume and internal porosity of bulk-fill resin composite restoration.

This study explores the effects of aging (thermal cycling and cyclic loading-TC/CL) and different light-curing unit (LCU) types on the volume characteristics and internal porosity of a bulk-fill resin-based composite restoration. Occlusal cavities (4 × 4 × 3 mm) were prepared on extracted human molars (n = 5). Tetric N-Bond Universal was applied, and the cavities were restored using Tetric-N-Ceram Bulk Fill. Photoactivation was performed using a quartz-tungsten halogen (QTH) or a multiple-emission peak light-emitting diode (MLED). Digital images for all restorations were obtained using microcomputed tomography (micro-CT) before (baseline) and after (post-aging) TC/CL (5,000 TC cycles in 5-55 °C baths and a dwell time of 30 s followed by 10,000 sinusoidal CL load cycles in an Instron B3000 at 2 Hz and 10-110 N) and storage (37 °C) for three months. For the micro-CT analysis, three-dimensional images were used to determine the restoration volume and internal porosity. Data were analyzed using a two-way ANOVA and Tukey's test (p < 0.05). Restorations photoactivated with QTH exhibited a higher object volume than the LED group at baseline and in post-aging conditions without any significant differences in the other evaluated characteristics. All volume/porosity characteristics increased considerably after TC/CL aging, except for the object volume of the QTH group and the closed porosity of the MLED group. The change in all the volume/porosity characteristics between both LCU groups after TC/CL were not significantly different. Thus, the aging process simulated herein increased the volume and porosity characteristics of the bulk-fill restoration, and no significant differences were obtained between the QTH and MLED equipment.

Photocrosslinkable methacrylated gelatin hydrogel as a cell-friendly injectable delivery system for chlorhexidine in regenerative endodontics.

OBJECTIVES: This work sought to formulate photocrosslinkable chlorhexidine (CHX)-laden methacrylated gelatin (CHX/GelMA) hydrogels with broad spectrum of action against endodontic pathogens as a clinically viable cell-friendly disinfection therapy prior to regenerative endodontics procedures. METHODS: CHX/GelMA hydrogel formulations were successfully synthesized using CHX concentrations between 0.12 % and 5 % w/v. Hydrogel microstructure was evaluated by scanning electron microscopy (SEM). Swelling and enzymatic degradation were assessed to determine microenvironmental effects. Compression test was performed to investigate the influence of CHX incorporation on the hydrogels' biomechanics. The antimicrobial and anti-biofilm potential of the formulated hydrogels were assessed using agar diffusion assays and a microcosms biofilm model, respectively. The cytocompatibility was evaluated by exposing stem cells from human exfoliated deciduous teeth (SHEDs) to hydrogel extracts (i.e., leachable byproducts obtained from overtime hydrogel incubation in phosphate buffer saline). The data were analyzed using One- and Two-way ANOVA and Tukey's test (α = 0.05). RESULTS: CHX/GelMA hydrogels were effectively prepared. NMR spectroscopy confirmed the incorporation of CHX into GelMA. The addition of CHX did not change the micromorphology (pore size) nor the swelling profile (p > 0.05). CHX incorporation reduced the degradation rate of the hydrogels (p < 0.001); whereas, it contributed to increased compressive modulus (p < 0.05). Regarding the antimicrobial properties, the incorporation of CHX showed a statistically significant decrease in the number of bacteria colonies at 0.12 % and 0.5 % concentration (p < 0.001) and completely inhibited the growth of biofilm at concentration levels 1 %, 2 %, and 5 %. Meanwhile, the addition of CHX, regardless of the concentration, did not lead to cell toxicity, as cell viability values were above 70 %. SIGNIFICANCE: The addition of CHX into GelMA showed significant antimicrobial action against the pathogens tested, even at low concentrations, with the potential to be used as a cell-friendly injectable drug delivery system for root canal disinfection prior to regenerative endodontics.

Engineering of Injectable Antibiotic-laden Fibrous Microparticles Gelatin Methacryloyl Hydrogel for Endodontic Infection Ablation.

This study aimed at engineering cytocompatible and injectable antibiotic-laden fibrous microparticles gelatin methacryloyl (GelMA) hydrogels for endodontic infection ablation. Clindamycin (CLIN) or metronidazole (MET) was added to a polymer solution and electrospun into fibrous mats, which were processed via cryomilling to obtain CLIN- or MET-laden fibrous microparticles. Then, GelMA was modified with CLIN- or MET-laden microparticles or by using equal amounts of each set of fibrous microparticles. Morphological characterization of electrospun fibers and cryomilled particles was performed via scanning electron microscopy (SEM). The experimental hydrogels were further examined for swelling, degradation, and toxicity to dental stem cells, as well as antimicrobial action against endodontic pathogens (agar diffusion) and biofilm inhibition, evaluated both quantitatively (CFU/mL) and qualitatively via confocal laser scanning microscopy (CLSM) and SEM. Data were analyzed using ANOVA and Tukey's test (α = 0.05). The modification of GelMA with antibiotic-laden fibrous microparticles increased the hydrogel swelling ratio and degradation rate. Cell viability was slightly reduced, although without any significant toxicity (cell viability > 50%). All hydrogels containing antibiotic-laden fibrous microparticles displayed antibiofilm effects, with the dentin substrate showing nearly complete elimination of viable bacteria. Altogether, our findings suggest that the engineered injectable antibiotic-laden fibrous microparticles hydrogels hold clinical prospects for endodontic infection ablation.

Effects of alternatively used thermal treatments on the mechanical and fracture behavior of dental resin composites with varying filler content.

The purpose of this study was two-fold: (i) to investigate whether the thermal treatment of direct dental resin composites (RCs) using microwave or autoclave heating cycles would modify the materials' strength as compared to the protocol without heating (control); and (ii) to compare the mechanical performance of direct and indirect RCs. Three RCs (from 3M ESPE) were tested: one indirect (Sinfony); and two direct materials (microhybrid - Filtek Z250; and nanofilled - Filtek Z350). Specimens from the direct RCs were prepared and randomly allocated into three groups according to the thermal treatment (n = 10): Control - no thermal treatment was performed; Microwave - the wet heating was performed using a microwave oven; and Autoclave - the wet heating was performed in an autoclave oven. The indirect RC was prepared following the instructions of the manufacturer. All materials were tested using flexural strength, elastic modulus, work of fracture (Wf), microhardness, and scanning electron microscopy (SEM) analyses. Data were analyzed with ANOVA and Tukey as well as Weibull analysis (α = 0.05). The thermal treatments tended to produce slight changes in the topography of direct RCs, especially by the autoclave' wet heating. Overall, the physico-mechanical properties changed after thermal treatment, although this effect was dependent on the type of RC and on the heating protocol. Sinfony showed the lowest modulus and hardness of the study, although it was the most compliant system (higher work of fracture). The load-deflection ability was also greater for the indirect RC. Reliability of the tested materials was similar among each other (p > 0.05). In conclusion, the alternative thermal treatments suggested here may significantly influence some aspects of the mechanical behavior of dental resin composites, with negative effects relying on both the chemical composition of the restorative material as well as on the wet heating protocol used. Clinicians should be aware of the possible effects that additional wet heating of direct resin composites using microwave or autoclave thermal protocols as performed here could have on the overall fracture and mechanical responses during loading circumstances.

The role of nanohydroxyapatite on the morphological, physical, and biological properties of chitosan nanofibers.

OBJECTIVES: This study aimed to evaluate the effects of nanohydroxyapatite (nHAp) particles on the morphological, chemical, physical, and biological properties of chitosan electrospun nanofibers. MATERIALS AND METHODS: nHAp particles with a 1.67 Ca/P ratio were synthesized via the aqueous precipitation method, incorporated into chitosan polymer solution (0.5 wt%), and electrospun into nHAp-loaded fibers (ChHa fibers). Neat chitosan fibers (nHAp-free, Ch fibers) were used as the control. The electrospun fiber mats were characterized using morphological, topographical, chemical, thermal, and a range of biological (antibacterial, antibiofilm, cell viability, and alkaline phosphatase [ALP] activity) analyses. Data were analyzed using ANOVA and Tukey's test (α = 0.05). RESULTS: ChHa fibers demonstrated a bead-like morphology, with thinner (331 ± 110 nm) and smoother (Ra = 2.9 ± 0.3 µm) distribution as compared to the control fibers. Despite showing similar cell viability and ALP activity to Ch fibers, the ChHa fibers demonstrated greater antibacterial potential against most tested bacteria (except for P. intermedia), and higher antibiofilm activity against P. gingivalis biofilm. CONCLUSIONS: The incorporation of nHAp particles did not jeopardize the overall morphology, topography, physical, and biological characteristics of the chitosan nanofibers. CLINICAL RELEVANCE: The combination of nHAp particles with chitosan can be used to engineer bioactive, electrospun composite nanofibers with potential applications in regenerative dentistry.

Development of an antibacterial and anti-metalloproteinase dental adhesive for long-lasting resin composite restorations.

Despite all the advances in adhesive dentistry, dental bonds are still fragile due to degradation events that start during application of adhesive agents and the inherent hydrolysis of resin-dentin bonds. Here, we combined two outstanding processing methods (electrospinning and cryomilling) to obtain bioactive (antimicrobial and anti-metalloproteinase) fiber-based fillers containing a potent matrix metalloproteinase (MMP) inhibitor (doxycycline, DOX). Poly(ε)caprolactone solutions containing different DOX amounts (0, 5, 25, and 50 wt%) were processed via electrospinning, resulting in non-toxic submicron fibers with antimicrobial activity against Streptococcus mutans and Lactobacillus. The fibers were embedded in a resin blend, light-cured, and cryomilled for the preparation of fiber-containing fillers, which were investigated with antibacterial and in situ gelatin zymography analyzes. The fillers containing 0, 25, and 50 wt% DOX-releasing fibers were added to aliquots of a two-step, etch-and-rinse dental adhesive system. Mechanical strength, hardness, degree of conversion (DC), water sorption and solubility, bond strength to dentin, and nanoleakage analyses were performed to characterize the physico-mechanical, biological, and bonding properties of the modified adhesives. Statistical analyses (ANOVA; Kruskal-Wallis) were used when appropriate to analyze the data (α = 0.05). DOX-releasing fibers were successfully obtained, showing proper morphological architecture, cytocompatibility, drug release ability, slow degradation profile, and antibacterial activity. Reduced metalloproteinases (MMP-2 and MMP-9) activity was observed only for the DOX-containing fillers, which have also demonstrated antibacterial properties against tested bacteria. Adhesive resins modified with DOX-containing fillers demonstrated greater DC and similar mechanical properties as compared to the fiber-free adhesive (unfilled control). Concerning bonding performance to dentin, the experimental adhesives showed similar immediate bond strengths to the control. After 12 months of water storage, the fiber-modified adhesives (except the group consisting of 50 wt% DOX-loaded fillers) demonstrated stable bonds to dentin. Nanoleakage was similar among all groups investigated. DOX-releasing fibers showed promising application in developing novel dentin adhesives with potential therapeutic properties and MMP inhibition ability; antibacterial activity against relevant oral pathogens, without jeopardizing the physico-mechanical characteristics; and bonding performance of the adhesive.

Single-session Endodontic Treatment is a Reality in Low-income Areas in Brazil?

AIM: The present study aimed to investigate the total number of visits required to conclude root canal treatments (RCTs) as well as the motivations associated to the choice of dentists practicing in low-income areas of Brazil. MATERIALS AND METHODS: A total of 3,103 questionnaires were electronically and individually delivered to professionals of Salvador, Sergipe, and Alagoas (Brazil). The questionnaire encompassed sociodemographic data and questions regarding the number of sessions required to conclude RCT. Also, postoperative pain, professional qualification, the use of technological resources, and time for one-visit treatment were evaluated. Data were analyzed using Chi-square and Poisson regression analyses (p < 0.05). RESULTS: A total of 326 responses were obtained with higher prevalence of specialists in the field of endodontics (36.8%). Dentists reported greater preference for rotary instrumentation (Alagoas 54.6%, Aracaju 62.1%, and Salvador 83.5%), and most of the participants reported multiple visits to treat root canals with the necrotic pulp tissue associated or not to periapical radiolucency, excluding Salvador (53.8%). Dentists who graduated in public dental schools were less likely to perform RCT of necrotic teeth with periapical lesion in one clinical appointment (p = 0.034). The single-session therapy was positively associated to continuing education attendance (p = 0.004) and to the occurrence of clinical complications (p < 0.001). Dentists who graduated in lato sensu programs were more likely to conclude RCT in less than 60 minutes (p < 0.001), although the occurrence of postoperative pain was more likely observed upon this scenario (p < 0.001). CONCLUSION: Despite the social inequalities in the analyzed area, professionals have been seeking for knowledge by means of continuing education programs and the implementation of technological resources in their clinical routine, although this fact has poorly influenced the acceleration of RCT. Clinical significances: The total number of visits to conclude endodontic treatment may be influenced by both professional and biological parameters such as the attendance to postgraduation programs and the use of technology as well as to the biological condition of the pulp and the occurrence of postoperative complications.

The role of polymeric nanofibers on the mechanical behavior of polymethyl methacrylate resin.

This study aimed to synthesize and characterize non-woven acrylonitrile butadiene styrene (ABS), polyamide-6 (P6), and polystyrene (PS) nanofibers, and evaluate their effects on the flexural strength and fracture resistance of fiber-modified polymethyl methacrylate (PMMA) resin. ABS, P6, and PS polymer solutions were prepared and electrospun into fiber mats, which were characterized by means of morphological, chemical, physical, and mechanical analyses. The fiber mats were then used to modify a thermally-activated PMMA resin, resulting in four testing groups: one unmodified group (control) and three fiber-modified groups incorporated with ABS, P6, or PS fiber mats. Flexural strength, work of fracture, and fractographic analysis were performed for all groups. Data were analyzed using Kruskal-Wallis or ANOVA tests (α = 0.05). The fiber diameter decreased, respectively, as follows: ABS > P6 > PS. Only the P6 fiber mats demonstrated a crystalline structure. Wettability was similar among the distinct fiber mats, although tensile strength was significantly greater for P6, followed by ABS, and then PS mats. Flexural strength of the fiber-modified PMMA resins was similar to the control, except for the weaker P6-based material. The work of fracture seemed to be greater and lower when the P6 and PS fibers were used, respectively. The fiber-modified groups exhibited a rougher pattern in the fractured surfaces when compared to the control, which may suggest that the presence of fibers deviates the direction of crack propagation, making the fracture mechanism of the PMMA resin more dynamic. While the neat PMMA showed a typical brittle response, the fiber-modified PMMA resins demonstrated a ductile response, combined with voids, suggesting large shear deformation during fracture. Altogether, despite the lack of direct reinforcement in the mechanical strength of the PMMA resin, the use of electrospun fibers showed promising application for the improvement of fracture behavior of PMMA resins, turning them into more compliant materials, although this effect may depend on the fiber composition.

Antimicrobial Therapeutics in Regenerative Endodontics: A Scoping Review.

INTRODUCTION: This review aimed to provide a critical appraisal of alternative antimicrobial strategies in lieu of traditional triple antibiotic paste (TAP). METHODS: This review followed the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement. The literature search was performed in 8 databases (PubMed/Medline, Embase, LILACS, Web of Science, Scopus, BVS, SciELO, and the Cochrane Library), selecting clinical, in vitro, in vivo, and in situ studies that evaluated antimicrobial alternatives to TAP in regenerative endodontics. Studies lacking an experimental TAP group were excluded. RESULTS: A total of 1705 potentially relevant records were initially identified. From the 38 studies retrieved for full-text reading, 16 fulfilled all selection criteria and were included in the qualitative analysis. According to the study design, 11 studies were solely in vitro, 1 study was both in vitro and in vivo (animal model), 2 studies were solely animal experiments, and 2 studies were clinical trials. The alternative antimicrobial agents to TAP consisted of modified TAP formulations (eg, a combination of TAP with chitosan); TAP-eluting nanofibers; propolis; chlorhexidine (CHX) gels/solutions; double antibiotic pastes composed of distinct combinations of antibiotics; Ca(OH)2-based formulations; and sodium hypochlorite. Overall, most of the alternative agents performed similarly to TAP, although some strategies (eg, Ca(OH)2- and CHX-based formulations) seemed to present dubious importance in the control of infection. CONCLUSIONS: TAP still remains an excellent option in terms of the complete elimination of microorganisms. This review points to the use of electrospun fibers as a drug delivery system to offer a controlled release of the antimicrobial agent, as well as the use of natural compounds, deserving future investigation.

Harnessing biomolecules for bioinspired dental biomaterials.

Dental clinicians have relied for centuries on traditional dental materials (polymers, ceramics, metals, and composites) to restore oral health and function to patients. Clinical outcomes for many crucial dental therapies remain poor despite many decades of intense research on these materials. Recent attention has been paid to biomolecules as a chassis for engineered preventive, restorative, and regenerative approaches in dentistry. Indeed, biomolecules represent a uniquely versatile and precise tool to enable the design and development of bioinspired multifunctional dental materials to spur advancements in dentistry. In this review, we survey the range of biomolecules that have been used across dental biomaterials. Our particular focus is on the key biological activity imparted by each biomolecule toward prevention of dental and oral diseases as well as restoration of oral health. Additional emphasis is placed on the structure-function relationships between biomolecules and their biological activity, the unique challenges of each clinical condition, limitations of conventional therapies, and the advantages of each class of biomolecule for said challenge. Biomaterials for bone regeneration are not reviewed as numerous existing reviews on the topic have been recently published. We conclude our narrative review with an outlook on the future of biomolecules in dental biomaterials and potential avenues of innovation for biomaterial-based patient oral care.

Chlorhexidine-modified nanotubes and their effects on the polymerization and bonding performance of a dental adhesive.

OBJECTIVES: The purpose of this study was to synthesize chlorhexidine (CHX)-encapsulated aluminosilicate clay nanotubes (Halloysite®, HNTs) and to incorporate them into the primer/adhesive components of an etch-and-rinse adhesive system (SBMP; Scotchbond Multipurpose, 3M ESPE) and to test their effects on degree of conversion, viscosity, immediate and long-term bonding to dentin. METHODS: CHX-modified HNTs were synthesized using 10% or 20% CHX solutions. The primer and the adhesive components of SBMP were incorporated with 15wt.% of the CHX-encapsulated HNTs. Degree of conversion (DC) and viscosity analyses were performed to characterize the modified primers/adhesives. For bond strength testing, acid-etched dentin was treated with one of the following: SBMP (control); 0.2%CHX solution before SBMP; CHX-modified primers+SBMP adhesive; SBMP primer+CHX-modified adhesives; and SBMP primer+CHX-free HNT-modified adhesive. The microtensile bond strength test was performed after immediate (24h) and long-term (6 months) of water storage. Data were analyzed using ANOVA and Tukey (α=5%) and the Weibull analysis. RESULTS: DC was greater for the CHX-free HNT-modified adhesive, whereas the other experimental adhesives showed similar DC as compared with the control. Primers were less viscous than the adhesives, without significant differences within the respective materials. At 24h, all groups showed similar bonding performance and structural reliability; whereas at the 6-month period, groups treated with the 0.2%CHX solution prior bonding or with the CHX-modified primers resulted in greater bond strength than the control and superior reliability. SIGNIFICANCE: The modification of a primer or adhesive with CHX-encapsulated HNTs was an advantageous approach that did not impair the polymerization, viscosity and bonding performance of the materials, showing a promising long-term effect on resin-dentin bonds.

Curcumin-A Natural Medicament for Root Canal Disinfection: Effects of Irrigation, Drug Release, and Photoactivation.

INTRODUCTION: Curcumin incorporation into polymeric fibers was tested for its antimicrobial properties and potential use in root canal disinfection. METHODS: Curcumin-modified fibers were processed via electrospinning and tested against a 7-day old established Actinomyces naeslundii biofilm. The medicaments tested were as follows: curcumin-modified fibers at 2.5 and 5.0 mg/mL, curcumin-based irrigant at 2.5 and 5.0 mg/mL, saline solution (negative control), and the following positive controls: 2% chlorhexidine, 1% sodium hypochlorite, and triple antibiotic paste (TAP, 1 mg/mL). All medicaments, except for the positive controls, were allocated according to the light exposure protocol (ie, photoactivation with a light-emitting diode every 30 seconds for 4 minutes or without photoactivation). After treatment, the medicaments were removed, and 1 mL saline solution was added; the biofilm was scraped from the well and used to prepare a 1:2000 dilution. Spiral plating was performed using anaerobic blood agar plates. After 24 hours, colony-forming units (colony-forming units/mL, n = 11/group) were counted to determine the antimicrobial effects. RESULTS: Data exhibited significant antimicrobial effects on the positive control groups followed by the curcumin irrigants and, lastly, the photoactivated curcumin-modified fibers. There was a significant reduction of viable bacteria in curcumin-based irrigants, which was greater than the TAP-treated group. Curcumin-free fibers, saline, and the nonphotoactivated curcumin-modified fibers did not display antimicrobial activity. CONCLUSIONS: Curcumin seems to be a potential alternative to TAP when controlling infection, but it requires a minimal concentration (2.5 mg/mL) to be effective. Photoactivation of curcumin-based medicaments seems to be essential to obtain greater antibiofilm activity.

A novel patient-specific three-dimensional drug delivery construct for regenerative endodontics.

Evoked bleeding (EB) clinical procedure, comprising a disinfection step followed by periapical tissue laceration to induce the ingrowth of undifferentiated stem cells from the periodontal ligament and alveolar bone, is currently the only regenerative-based therapeutic approach to treating pulp tissue necrosis in undeveloped (immature) permanent teeth approved in the United States. Yet, the disinfection step using antibiotic-based pastes leads to cytotoxic, warranting a biocompatible strategy to promote root canal disinfection with no or minimal side-effects to maximize the regenerative outcomes. The purpose of this investigation was to develop a tubular three-dimensional (3D) triple antibiotic-eluting construct for intracanal drug delivery. Morphological (scanning electron microscopy), chemical (Fourier transform infrared spectroscopy), and mechanical (tensile testing) characteristics of the polydioxanone-based triple antibiotic-eluting fibers were assessed. The antimicrobial properties of the tubular 3D constructs were determined in vitro and in vivo using an infected (Actinomyces naeslundii) dentin tooth slice model and a canine method of periapical disease, respectively. The in vitro data indicated significant antimicrobial activity and the ability to eliminate bacterial biofilm inside dentinal tubules. In vivo histological findings demonstrated that, using the EB procedure, the tubular 3D triple antibiotic-eluting construct allowed the formation of an appropriate environment that led to apex closure and the ingrowth of a thin layer of osteodentin-like tissue into the root canal. Taken together, these findings indicate that our novel drug delivery construct is a promising biocompatible disinfection strategy for immature permanent teeth with necrotic pulps. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 107B: 1576-1586, 2019.

Recent Advances in Adhesive Bonding - The Role of Biomolecules, Nanocompounds, and Bonding Strategies in Enhancing Resin Bonding to Dental Substrates.

PURPOSE OF REVIEW: To present an overview on the main agents (i.e., biomolecules and nanocompounds) and/or strategies currently available to amplify or stabilize resin-dentin bonding. RECENT FINDINGS: According to studies retrieved for full text reading (2014-2017), there are currently six major strategies available to overcome resin-dentin bond degradation: (i) use of collagen crosslinking agents, which may form stable covalent bonds with collagen fibrils, thus strengthening the hybrid layer; (ii) use of antioxidants, which may allow further polymerization reactions over time; (iii) use of protease inhibitors, which may inhibit or inactivate metalloproteinases; (iv) modification of the bonding procedure, which may be performed by using the ethanol wet-bonding technique or by applying an additional adhesive (hydrophobic) coating, thereby strengthening the hybrid layer; (v) laser treatment of the substrate prior to bonding, which may cause specific topographic changes in the surface of dental substrates, increasing bonding efficacy; and (vi) reinforcement of the resin matrix with inorganic fillers and/or remineralizing agents, which may positively enhance physico-mechanical properties of the hybrid layer. SUMMARY: With the present review, we contributed to the better understanding of adhesion concepts and mechanisms of resin-dentin bond degradation, showing the current prospects available to solve that problematic. Also, adhesively-bonded restorations may be benefited by the use of some biomolecules, nanocompounds or alternative bonding strategies in order to minimize bond strength degradation.

Tetracycline-incorporated polymer nanofibers as a potential dental implant surface modifier.

This study investigated the antimicrobial and osteogenic properties of titanium (Ti) disks superficially modified with tetracycline (TCH)-incorporated polymer nanofibers. The experiments were carried out in two phases. The first phase dealt with the synthesis and characterization (i.e., morphology, mechanical strength, drug release, antimicrobial activity, and cytocompatibility) of TCH-incorporated fibers. The second phase was dedicated to evaluating both the antimicrobial and murine-derived osteoprecursor cell (MC3T3-E1) response of Ti-modified with TCH-incorporated fibers. TCH was successfully incorporated into the submicron-sized and cytocompatible fibers. All TCH-incorporated mats presented significant antimicrobial activity against periodontal pathogens. The antimicrobial potential of the TCH-incorporated fibers-modified Ti was influenced by both the TCH concentration and bacteria tested. At days 5 and 7, a significant increase in MC3T3-E1 cell number was observed for TCH-incorporated nanofibers-modified Ti disks when compared to that of TCH-free nanofibers-modified Ti-disks and bare Ti. A significant increase in alkaline phosphatase (ALP) levels on the Ti disks modified with TCH-incorporated nanofiber on days 7 and 14 was seen, suggesting that the proposed surface promotes early osteogenic differentiation. Collectively, the data suggest that TCH-incorporated nanofibers could function as an antimicrobial surface modifier and osteogenic inducer for Ti dental implants. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 2085-2092, 2017.

Effects of Simulated Gastric Juice on CAD/CAM Resin Composites-Morphological and Mechanical Evaluations.

PURPOSE: To evaluate the effects of simulated gastric juice on CAD/CAM resin composites by means of morphological and mechanical (i.e., hardness) evaluations. MATERIALS AND METHODS: Fourteen specimens of each resin composite (Lava Ultimate and Paradigm MZ100) were prepared according to the manufacturer's instructions. They were submitted to erosive challenges in a simulated gastric juice (pH = 1.2) solution for 6 and 24 hours. Vickers microhardness and surface roughness (Ra , Rq ) evaluations were taken before (baseline) and after acid exposure. Morphological analysis was obtained using scanning electron microscopy (SEM). Statistical analysis was performed using two-way repeated measures ANOVA and Student-Newman-Keuls's test (α = 0.05). RESULTS: Paradigm MZ100 demonstrated higher microhardness than Lava Ultimate regardless of the storage time period (p ≤ 0.001), and microhardness was not affected by the acidic challenge (p = 0.58). After 6 hours of acid exposure, a significant decrease in Ra and Rq was seen for Paradigm MZ100 when compared to the baseline (Ra p = 0.032; Rq p = 0.013); however, for Lava Ultimate only Rq decreased (p = 0.021), while Ra remained unchanged (p = 0.38). After 24 hours of acid exposure, while Paradigm MZ100 exhibited no additional changes in surface roughness (p ≥ 0.75), Lava Ultimate became rougher (Ra p = 0.041; Rq p = 0.014), as confirmed by SEM imaging. CONCLUSIONS: The acidic scenario tested in the present study changed the surface roughness of the resin composites but not their Vickers microhardness. Moreover, both resin composites seem suitable for use under acidic scenarios, although Paradigm MZ100 showed enhanced stability compared to Lava Ultimate.

Stain removal effect of novel papain- and bromelain-containing gels applied to enamel.

OBJECTIVES: The aims of the study are to prepare novel stain removal gel-based formulations containing papain or bromelain and to investigate their stain removal effect when applied to enamel. MATERIALS AND METHODS: Experimental bromelain- and papain-based stain removal gels were prepared. Next, enamel/dentin tooth samples (6 × 6 mm2, 4 mm in thickness) were obtained from bovine teeth, stained in coffee solution for 1 week, and measured with a digital spectrophotometer (Easyshade, Vita Zahnfabrik) for color assessment (baseline). The samples were then randomly allocated into four groups (n = 7), according to the stain removal agent applied: ContrastPM+ (Discus Dental, LLC), which is based on 20 wt.% carbamide peroxide (positive control); bromelain-based; papain-based; and no agent (negative control). The materials were applied once a week, three times per day, during 4 weeks, and following the directions of use from positive control. The samples were measured again with the Easyshade and using the CIEL * a * b * color system. The color change (ΔE *) results were obtained by subtracting the baseline values from the final color values obtained at each time point. The data were statistically analyzed using two-way repeated-measures analysis of variance and Student Newman Keuls's test as a post hoc test (α = 5 %). RESULTS: All stain removal agents produced greater color change than the negative control (p < .001), with the positive control demonstrating greater ΔE * values when compared to the experimental gels (p ≤ .004). The second application of all gels resulted in greater ΔE * values compared to the first application (p ≤ .025), although no color change was observed after the third application (p ≥ .051), regardless of the material evaluated. CLINICAL SIGNIFICANCE: The proposed gels containing proteolytic enzymes (bromelain or papain) of vegetal origin may hold significant clinical potential as active agents for the preparation of stain removal agents free of hydrogen/carbamide peroxide.

Synthesis and characterization of CaO-loaded electrospun matrices for bone tissue engineering.

OBJECTIVES: This study aims to synthesize and characterize biodegradable polymer-based matrices loaded with CaO nanoparticles for osteomyelitis treatment and bone tissue engineering. MATERIALS AND METHODS: Poly(ε-caprolactone) (PCL) and PCL/gelatin (1:1, w/w) solutions containing CaO nanoparticles were electrospun into fibrous matrices. Scanning (SEM) and transmission (TEM) electron microscopy, Fourier transformed infrared (FTIR), energy dispersive X-ray spectroscopy (EDS), contact angle (CA), tensile testing, and antibacterial activity (agar diffusion assay) against Staphylococcus aureus were performed. Osteoprecursor cell (MC3T3-E1) response (i.e., viability and alkaline phosphatase expression/ALP) and infiltration into the matrices were evaluated. RESULTS: CaO nanoparticles were successfully incorporated into the fibers, with the median fiber diameter decreasing after CaO incorporation. The CA decreased with the addition of CaO, and the presence of gelatin made the matrix very hydrophilic (CA = 0°). Increasing CaO concentrations progressively reduced the mechanical properties (p ≤ 0.030). CaO-loaded matrices did not display consistent antibacterial activity. MC3T3-E1 cell viability demonstrated the highest levels for CaO-loaded matrices containing gelatin after 7 days in culture. An increased ALP expression was consistently seen for PCL/CaO matrices when compared to PCL and gelatin-containing counterparts. CONCLUSIONS: Despite inconsistent antibacterial activity, CaO nanoparticles can be effectively loaded into PCL or PCL/gelatin fibers without negatively affecting the overall performance of the matrices. More importantly, CaO incorporation enhanced cell viability as well as differentiation capacity, as demonstrated by an increased ALP expression. CLINICAL SIGNIFICANCE: CaO-loaded electrospun matrices show potential for applications in bone tissue engineering.