Pin penetration depths in the neurocranium using a three-pin head fixation device.

In estimated 10-15% of neurosurgical interventions employing a conventional three-pin head fixation device (HFD) the patient's head loses position due to slippage. At present no scientifically based stability criterion exists to potentially prevent the intraoperative loss of head position or skull fractures. Here, data on the skull penetration depth both on the single and two-pin side of a three-pin HFD are presented, providing scientific evidence for a stability criterion for the invasive three-pin head fixation. Eight fresh, chemically untreated human cadaveric heads were sequentially pinned 90 times in total in a noncommercially calibrated clamp screw applying a predefined force of 270 N (approximately 60 lbf) throughout. Three head positions were pinned each in standardized manner for the following approaches: prone, middle fossa, pterional. Titanium-aluminum alloy pins were used, varying the pin-cone angle on the single-pin side from 36° to 55° and on the two-pin side from 25° to 36°. The bone-penetration depths were directly measured by a dial gauge on neurocranium. The penetration depths on the single-pin side ranged from 0.00 mm (i.e., no penetration) to 6.17 mm. The penetration depths on the two-pin side ranged from 0.00 mm (no penetration) to 4.48 mm. We measured a significantly higher penetration depth for the anterior pin in comparison to the posterior pin on the two-pin side in prone position. One pin configuration (50°/25°) resulted in a quasi-homogenous pin depth distribution between the single- and the two-pin side. Emanating from the physical principle that pin depths behave proportionate to pin pressure distribution, a quasi-homogenous pin penetration depth may result in higher resilience against external shear forces or torque, thus reducing potential complications such as slippage and depressed skull fractures. The authors propose that the pin configuration of 50°/25° may be superior to the currently used uniform pin-cone angle distribution in common clinical practice (36°/36°). However, future research may identify additional influencing factors to improve head fixation stability.

Rain may improve survival from direct lightning strikes to the human head.

There is evidence that humans can survive a direct lightning strike to the head. Our question is: could water (rain) on the skin contribute to an increase in the survival rate? We measure the influence of rain during high-energy direct lightning strikes on a realistic three-compartment human head phantom. We find a lower number of perforations and eroded areas near the lightning strike impact points on the head phantom when rain was applied compared to no rain. Current amplitudes in the brain were lower with rain compared to no rain before a fully formed flashover. We conclude that rain on the scalp potentially contributes to the survival rate of 70-90% due to: (1) lower current exposition in the brain before a fully formed flashover, and (2) reduced mechanical and thermal damage.

The Arch Electrode: A Novel Dry Electrode Concept for Improved Wearing Comfort.

Electroencephalography (EEG) is increasingly used for repetitive and prolonged applications like neurofeedback, brain computer interfacing, and long-term intermittent monitoring. Dry-contact electrodes enable rapid self-application. A common drawback of existing dry electrodes is the limited wearing comfort during prolonged application. We propose a novel dry Arch electrode. Five semi-circular arches are arranged parallelly on a common baseplate. The electrode substrate material is a flexible thermoplastic polyurethane (TPU) produced by additive manufacturing. A chemical coating of Silver/Silver-Chloride (Ag/AgCl) is applied by electroless plating using a novel surface functionalization method. Arch electrodes were manufactured and validated in terms of mechanical durability, electrochemical stability, in vivo applicability, and signal characteristics. We compare the results of the dry arch electrodes with dry pin-shaped and conventional gel-based electrodes. 21-channel EEG recordings were acquired on 10 male and 5 female volunteers. The tests included resting state EEG, alpha activity, and a visual evoked potential. Wearing comfort was rated by the subjects directly after application, as well as at 30 min and 60 min of wearing. Our results show that the novel plating technique provides a well-adhering electrically conductive and electrochemically stable coating, withstanding repetitive strain and bending tests. The signal quality of the Arch electrodes is comparable to pin-shaped dry electrodes. The average channel reliability of the Arch electrode setup was 91.9 ± 9.5%. No considerable differences in signal characteristics have been observed for the gel-based, dry pin-shaped, and arch-shaped electrodes after the identification and exclusion of bad channels. The comfort was improved in comparison to pin-shaped electrodes and enabled applications of over 60 min duration. Arch electrodes required individual adaptation of the electrodes to the orientation and hairstyle of the volunteers. This initial preparation time of the 21-channel cap increased from an average of 5 min for pin-like electrodes to 15 min for Arch electrodes and 22 min for gel-based electrodes. However, when re-applying the arch electrode cap on the same volunteer, preparation times of pin-shaped and arch-shaped electrodes were comparable. In summary, our results indicate the applicability of the novel Arch electrode and coating for EEG acquisition. The novel electrode enables increased comfort for prolonged dry-contact measurement.

Head phantoms for bioelectromagnetic applications: a material study.

BACKGROUND: Assessments of source reconstruction procedures in electroencephalography and computations of transcranial electrical stimulation profiles require verification and validation with the help of ground truth configurations as implemented by physical head phantoms. For these phantoms, synthetic materials are needed, which are mechanically and electrochemically stable and possess conductivity values similar to the modeled human head tissues. Three-compartment head models comprise a scalp layer with a conductivity range of 0.137 S/m to 2.1 S/m, a skull layer with conductivity values between 0.066 S/m and 0.00275 S/m, and an intracranial volume with an often-used average conductivity value of 0.33 S/m. To establish a realistically shaped physical head phantom with a well-defined volume conduction configuration, we here characterize the electrical conductivity of synthetic materials for modeling head compartments. We analyzed agarose hydrogel, gypsum, and sodium chloride (NaCl) solution as surrogate materials for scalp, skull, and intracranial volume. We measured the impedance of all materials when immersed in NaCl solution using a four-electrode setup. The measured impedance values were used to calculate the electrical conductivity values of each material. Further, the conductivities in the longitudinal and transverse directions of reed sticks immersed in NaCl solution were measured to test their suitability for mimicking the anisotropic conductivity of white matter tracts. RESULTS: We obtained conductivities of 0.314 S/m, 0.30 S/m, 0.311 S/m (2%, 3%, 4% agarose), 0.0425 S/m and 0.0017 S/m (gypsum with and without NaCl in the compound), and 0.332 S/m (0.17% NaCl solution). These values are within the range of the conductivity values used for EEG and TES modeling. The reed sticks showed anisotropic conductivity with a ratio of 1:2.8. CONCLUSION: We conclude that agarose, gypsum, and NaCl solution can serve as stable representations of the three main conductivity compartments of the head, i.e., scalp, skull, and intracranial volume. An anisotropic conductivity structure such as a fiber track in white matter can be modeled using tailored reed sticks inside a volume conductor.

Measurement and analysis of partial lightning currents in a head phantom.

Direct lightning strikes to the human head can lead to various effects, ranging from burnings to death. The biological and physical mechanisms of a direct lightning strike in the human head are not well understood. The aim of this paper is to design an experimental setup to measure the spatial and temporal current distribution during a direct lightning strike to physical head phantoms to establish normative values for personal lightning protection equipment design and testing. We created head phantoms made of agarose, replicating the geometric and dielectric properties of scalp, skull, and intracranial volume. The bases of the three compartments were galvanically contacted via copper electrodes to measure the current per compartment. We used pulse generators to apply aperiodic voltage and current signals that modelled lightning components. Our experiments indicated that the scalp compartment was exposed to the current with a fraction of 80-90%. The brain and skull compartments were exposed between 6-13% and 3-6% of the total measured current respectively. In case of a flashover, most of the current (98-99%) flowed through the discharge channel. Unlike previous theoretical estimates and measurements in technical setups, we observed considerably longer times for the flashover to build up. In our experiments, the time to build up a fully formed flashover varied from approximately 30-700 µs. The observed current patterns in cases without and with flashover provided information on regions of possible damage in the human head. Consequently, we identified the phenomenon of a flashover as a potential mechanism for humans to survive a lightning strike. Our measured current distributions and amplitudes formed the base for normative values, which can be used in later experimental investigations regarding the possibilities of individual lightning protection equipment for humans.

Development of a head-phantom and measurement setup for lightning effects.

Direct lightning strikes to human heads lead to various effects ranging from Lichtenberg figures, over loss of consciousness to death. The evolution of the induced current distribution in the head is of great interest to understand the effect mechanisms. This work describes a technique to model a simplified head-phantom to investigate effects during direct lightning strike. The head-phantom geometry, conductive and dielectric parameters were chosen similar to that of a human head. Three layers (brain, skull, and scalp) were created for the phantom using agarose hydrogel doped with sodium chloride and carbon. The head-phantom was tested on two different impulse generators, which reproduce approximate lightning impulses. The effective current and the current distribution in each layer were analyzed. The biggest part of the current flowed through the brain layer, approx. 70 % in cases without external flashover. Approx. 23 % of the current flowed through skull layer and 6 % through the scalp layer. However, the current decreased within the head-phantom to almost zero after a complete flashover on the phantom occurred. The flashover formed faster with a higher impulse current level. Exposition time of current through the head decreases with a higher current level of the lightning impulse. This mechanism might explain the fact that people can survive a lightning strike. The experiments help to understand lightning effects on humans.