Comparative Analysis of Internal Tapered Implant-Abutment Connections: Evaluating the Morse Effect.

The purpose of the present study was to evaluate the Morse effect of different internal tapered implant-abutment connections (ITCs) using a pullout test. Implants with different ITCs were selected: Short (Bicon, USA), G1; Novo Colosso (Medens, Brazil), G2; Epkut (SIN, Brazil), G3; Strong SW (SIN, Brazil), G4; Flash (Conexão, Brazil), G5 and Bone Level (Straumann, Switzerland), G6. The respective CAD files were loaded into the analysis software to measure each ITC's taper angle and implant-abutment contact area. Six implants from each group were embedded in acrylic resin blocks, and the respective universal abutments were fixed using a mallet (G1) or by applying 20 Ncm of torque (G2 to G6). After ten minutes, each abutment's retention screw was removed, and the force necessary for abutment rupture was recorded using a universal testing machine at a crosshead speed of 0.5 mm/min. The groups were compared using a one-way ANOVA and Tukey's test. Spearman's correlation was used to check the correlation of the taper angle and contacting area with the pullout strength. G1, a no-screw abutment with a 3° taper, and G2, a 10°tapered abutment tightened by 20 Ncm, presented the highest pullout strength (p<.05). The increased taper angle of G4, compared to G3, reduced the Morse effect despite their similar implant-abutment contacting areas (p<0.05). The G5 and G6 abutments loosened after screw removal and did not exhibit pullout resistance. The closer the tapered angle (r=-.958) and the higher the implant-abutment contact area (r=.880), the higher the pullout strength (p<.001). Within the limits of this study, the Morse effect is different among tapered implant-abutment connections. The closer the tapered angle and the higher the interface area, the higher the Morse effect between the abutment and the implant.

The Association of Nanostructured Carbonated Hydroxyapatite with Denatured Albumin and Platelet-Rich Fibrin: Impacts on Growth Factors Release and Osteoblast Behavior.

Platelet-rich Fibrin (PRF), a second-generation blood concentrate, offers a versatile structure for bone regeneration due to its composition of fibrin, growth factors, and cytokines, with adaptations like denatured albumin-enriched with liquid PRF (Alb-PRF), showing potential for enhanced stability and growth factor dynamics. Researchers have also explored the combination of PRF with other biomaterials, aiming to create a three-dimensional framework for enhanced cell recruitment, proliferation, and differentiation in bone repair studies. This study aimed to evaluate a combination of Alb-PRF with nanostructured carbonated hydroxyapatite microspheres (Alb-ncHA-PRF), and how this association affects the release capacity of growth factors and immunomodulatory molecules, and its impact on the behavior of MG63 human osteoblast-like cells. Alb-PRF membranes were prepared and associated with nanocarboapatite (ncHA) microspheres during polymerization. MG63 cells were exposed to eluates of both membranes to assess cell viability, proliferation, mineralization, and alkaline phosphatase (ALP) activity. The ultrastructural analysis has shown that the spheres were shattered, and fragments were incorporated into both the fibrin mesh and the albumin gel of Alb-PRF. Alb-ncHA-PRF presented a reduced release of growth factors and cytokines when compared to Alb-PRF (p < 0.05). Alb-ncHA-PRF was able to stimulate osteoblast proliferation and ALP activity at lower levels than those observed by Alb-PRF and was unable to positively affect in vitro mineralization by MG63 cells. These findings indicate that the addition of ncHA spheres reduces the biological activity of Alb-PRF, impairing its initial effects on osteoblast behavior.

Clinical and Biochemical Evaluation of the Use of Alb-PRF versus L-PRF in Mandibular Third Molar Extractions: A Split-Mouth Randomized Clinical Trial.

Bone tissue engineering seeks biomaterials that enable cell migration, angiogenesis, matrix deposition, and tissue regeneration. Blood concentrates like platelet-rich fibrin (L-PRF) offer a cost-effective source of cells and growth factors to enhance healing. The present study aimed to evaluate heated serum albumin with liquid PRF (Alb-PRF) and L-PRF clinically and biochemically after placement in dental sockets following mandibular third molar extraction. In a controlled, split-mouth study involving 10 volunteers, 20 extracted molars were treated with either Alb-PRF or L-PRF. Post-extraction, pain, trismus, infection presence, and swelling were measured. The concentrations of different analytes in the surgical sites were also examined. The data were statistically analyzed, with significance defined at p < 0.05 (t-test). No significant difference was noted between the groups for pain and trismus, but Alb-PRF showed a significant reduction in swelling on day seven. The Alb-PRF group showed lower levels of pro-inflammatory cytokines (GM-CSF, IL-1b, IL-6, IFNy, IL-8, IL-15, RANTES, and MIP-1a) after seven days, with only higher expressions of MIP-1b, IL-1b, and MCP-1 found in the L-PRF group. Differences were observed in the release of analytes between L-PRF and Alb-PRF, with Alb-PRF significantly reducing edema after seven days. Alb-PRF reduced edema, while L-PRF increased inflammatory cytokines. When compared to L-PRF, Alb-PRF reduced edema and the release of inflammatory cytokines, suggesting promising effects in socket healing while underscoring the role of growth factors and cytokines in potential applications of blood concentrates.

The Interplay of Raloxifene and Sonochemical Bio-Oss in Early Maxillary Sinus Bone Regeneration: A Histological and Immunohistochemical Analysis in Rabbits.

The study aimed to assess the efficacy of using Raloxifene with ultrasonic processing to enhance Bio-Oss®, a bone graft substitute, for maxillary sinus bone height reconstruction. A total of 24 rabbit maxillary sinuses were distributed into three groups, each receiving different treatments: Bio-Oss® only, sonicated Bio-Oss, and sonicated Bio-Oss® with Raloxifene. Surgical procedures and subsequent histomorphometric and immunohistochemistry analyses were conducted to evaluate the bone formation, connective tissue, and remaining biomaterial, as well as the osteoblastic differentiation and maturation of collagen fibers. Results indicated that the sonicated Bio-Oss® and Bio-Oss® groups showed similar histological behavior and bone formation, but the Raloxifene group displayed inflammatory infiltrate, low bone formation, and disorganized connective tissue. The statistical analysis confirmed significant differences between the groups in terms of bone formation, connective tissue, and remaining biomaterial. In conclusion, the study found that while sonicated Bio-Oss® performed comparably to Bio-Oss® alone, the addition of Raloxifene led to an unexpected delay in bone repair. The findings stress the importance of histological evaluation for accurate bone repair assessment and the necessity for further investigation into the local application of Raloxifene. Future research may focus on optimizing bone substitutes with growth factors to improve bone repair.

Harnessing the Power of PAOO and Invisalign: An Interdisciplinary Approach to Orthodontic Care.

The present article explores the benefits of combining periodontally accelerated osteogenic orthodontics (PAOO) with Invisalign for optimal orthodontic treatment outcomes. PAOO is an interdisciplinary dental technique that minimizes complications and accelerates tooth movement while enhancing various orthodontic treatments. In conjunction with Invisalign, PAOO provides a discreet and comfortable solution for patients seeking to improve their smile. The study presents two challenging cases successfully treated using this combined approach, emphasizing the technique's potential to reduce treatment times and improve orthodontic outcomes. The interdisciplinary approach of PAOO ensures long-term success and stability by preserving periodontal structures and addressing potential bony defects. By incorporating bone grafting materials, PAOO helps prevent common concerns in traditional orthodontic treatments, such as bony defects and gingival recession. Furthermore, the combination with Invisalign offers a more aesthetically pleasing and comfortable treatment experience, allowing patients to maintain their self-esteem and confidence throughout the treatment. Despite the potential advantages, dental professionals must manage patient expectations and address potential complications to ensure the best possible results. Overall, the integration of PAOO and Invisalign demonstrates a viable alternative for patients who do not want to proceed with orthognathic surgery, enhancing patient satisfaction and overall treatment outcomes.

Standardization of Animal Models and Techniques for Platelet-Rich Fibrin Production: A Narrative Review and Guideline.

Experimental research is critical for advancing medical knowledge and enhancing patient outcomes, including in vitro and in vivo preclinical assessments. Platelet-rich fibrin (PRF) is a blood by-product that has garnered attention in the medical and dental fields due to its potential for tissue regeneration and wound healing. Animal models, such as rabbits and rats, have been used to produce PRF and examine its properties and applications. PRF has demonstrated potential in the dental and medical fields for reducing inflammation, promoting tissue repair, and accelerating wound healing. This narrative review aims to compare existing evidence and provide guidelines for PRF animal research, emphasizing the importance of standardizing animal models, following ethical considerations, and maintaining transparency and accountability. The authors highlight the necessity to use the correct relative centrifugal force (RCF), standardize centrifugal calibration, and report detailed information about blood collection and centrifuge parameters for reproducible results. Standardizing animal models and techniques is crucial for narrowing the gap between laboratory research and clinical applications, ultimately enhancing the translation of findings from bench to bedside.

"Sticky Bone" Preparation Device: A Pilot Study on the Release of Cytokines and Growth Factors.

Sticky bone, a growth factor-enriched bone graft matrix, is a promising autologous material for bone tissue regeneration. However, its production is strongly dependent on manual handling steps. In this sense, a new device was developed to simplify the confection of the sticky bone, named Sticky Bone Preparation Device (SBPD®). The purpose of this pilot study was to investigate the suitability of the SBPD® to prepare biomaterials for bone regeneration with autologous platelet concentrates. The SBPD® allows the blending of particulate samples from synthetic, xenograft, or autogenous bone with autologous platelet concentrates, making it easy to use and avoiding the need of further manipulations for the combination of the materials. The protocol for the preparation of sticky bone samples using the SBPD® is described, and the resulting product is compared with hand-mixed SB preparations regarding in vitro parameters such as cell content and the ability to release growth factors and cytokines relevant to tissue regeneration. The entrapped cell content was estimated, and the ability to release biological mediators was assessed after 7 days of incubation in culture medium. Both preparations increased the leukocyte and platelet concentrations compared to whole-blood samples (p < 0.05), without significant differences between SB and SBPD®. SBPD® samples released several growth factors, including VEGF, FGFb, and PDGF, at concentrations physiologically equivalent to those released by SB preparations. Therefore, the use of SBPD® results in a similar product to the standard protocol, but with more straightforward and shorter preparation times and less manipulation. These preliminary results suggest this device as a suitable alternative for combining bone substitute materials with platelet concentrates for bone tissue regeneration.

Osseodensification enables bone healing chambers with improved low-density bone site primary stability: an in vivo study.

Primary implant stability is a prerequisite for successful implant osseointegration. The osseodensification technique (OD) is a non-subtractive drilling technique that preserves the bone tissue, increases osteotomy wall density, and improves the primary stability. This study aimed to investigate the hypothesis that OD, through a wider osteotomy, produces healing chambers (HCs) at the implant-bone interface without impacting low-density bone primary stability. Twenty implants (3.5 × 10 mm) with a nanohydroxyapatite (nHA) surface were inserted in the ilium of ten sheep. Implant beds were prepared as follows: (i) 2.7-mm-wide using subtractive conventional drilling (SCD) technique (n = 10); (ii) 3.8-mm-wide using an OD bur system (n = 10). The sheep were randomized to two groups, with samples collected at either 14-(n = 5) or 28-days (n = 5) post-surgery and processed for histological and histomorphometric evaluation of bone-implant contact (BIC) and bone area fraction occupancy (BAFO). No significant group differences were found with respect to final insertion torque and implant stability quotient (p > 0.050). BIC values were higher for SCD after 14 and 28 days (p < 0.050); however, BAFO values were similar (p > 0.050). It was possible to conclude that the OD technique allowed a wider implant bed preparation without prejudice on primary stability and bone remodeling.

Silane-Coating Strategy for Titanium Functionalization Does Not Impair Osteogenesis In Vivo.

Silane-coating strategy has been used to bind biological compounds to the titanium surface, thereby making implant devices biologically active. However, it has not been determined if the presence of the silane coating itself is biocompatible to osseointegration. The aim of the present study was to evaluate if silane-coating affects bone formation on titanium using a rabbit model. For this, titanium screw implants (3.75 by 6 mm) were hydroxylated in a solution of H2SO4/30% H2O2 for 4 h before silane-coating with 3-aminopropyltriethoxysilane (APTES). A parallel set of titanium screws underwent only the hydroxylation process to present similar acid-etched topography as a control. The presence of the silane on the surface was checked by x-ray photoelectron spectroscopy (XPS), with scanning electron microscopy (SEM) and atomic force microscopy (AFM). A total of 40 titanium screws were implanted in the tibia of ten New Zealand rabbits in order to evaluate bone-to-implant contact (BIC) after 3 weeks and 6 weeks of healing. Silane-coated surface presented higher nitrogen content in the XPS analysis, while micro- and nano-topography of the surface remained unaffected. No difference between the groups was observed after 3 and 6 weeks of healing (p > 0.05, independent t-test), although an increase in BIC occurred over time. These results indicate that silanization of a titanium surface with APTES did not impair the bone formation, indicating that this can be a reliable tool to anchor osteogenic molecules on the surface of implant devices.

In vivo evaluation of the biocompatibility and biodegradation of a new denatured plasma membrane combined with liquid PRF (Alb-PRF).

Guided bone regeneration (GBR) is a process that involves the regeneration of bone defects through the application of occlusive membranes that mechanically exclude the population of non-osteogenic cells from the surrounding soft tissue. Interestingly, platelet-rich fibrin (PRF) has previously been proposed as an autologous GBR membrane despite its short-term resorption period of 2-3 weeks. Recent clinical observations have demonstrated that, by heating a liquid platelet-poor plasma (PPP) layer and mixing the cell-rich buffy coat zone, the resorption properties of heated albumin gel with liquid-PRF (Alb-PRF) can be significantly improved. The aim of this study was to evaluate the inflammatory reaction, biocompatibility, and extended degradation properties of a new autologous Alb-PRF membrane in comparison to commonly utilized standard PRF after nude mice implantation, according to ISO 10993-6/2016. Two standard preparations of PRF (L-PRF and H-PRF) were compared to novel Alb-PRF following subcutaneous implantation at 7, 14, and 21 days. All groups demonstrated excellent biocompatibility owing to their autologous sources. However, it is worth noting that, while both L-PRF and H-PRF membranes demonstrated significant or complete resorption by 21 days, the Alb-PRF membrane remained volume-stable throughout the duration of the study. This study demonstrates-for the first time, to the best of our knowledge-a marked improvement in the membrane stability of Alb-PRF. This indicates its future potential for use as a biological barrier membrane for GBR procedures with a long-lasting half-life, or as a biological filler material in esthetic medicine applications. Thus, further studies are warranted to explore future clinical applications in various fields of medicine.

Effects of rotor angle and time after centrifugation on the biological in vitro properties of platelet rich fibrin membranes.

This study evaluated the impact of rotor angle and time of storage after centrifugation on the in vitro biological properties of platelet-rich fibrin (PRF) membranes. Blood samples (n = 9) were processed with a vertical fixed-angle (V) or a swing-out horizontal (H) centrifuge, with 20-60 min of sample storage after centrifugation. Leukocytes, platelets, and red blood cells were counted, and fibrin architecture was observed by scanning electron microscopy (SEM). The release of FGF2, PDGFbb, VEGF, IL-6, and IL-1ß was measured after incubation on culture media for 7-21 days. Cell content was equivalent in all experimental groups (p > .05). The fibrin matrix was similar for fixed-angle and horizontal centrifugation. Horizontal centrifugation induced a twofold increase in PDGF and 1.7× increase on FGF release as compared to V samples, while IL-1ß was significantly reduced (p < .05). No significant difference was observed on the release of growth factors and cytokines at different times after centrifugation (p < .05). These data suggest that both angles of centrifugation produce PRF membranes with similar structure and cellularity, but horizontal centrifugation induces a higher release of growth factors. Higher times of storage after centrifugation did not impact on cell content and the release of growth factors.

The use of leukocyte- and platelet-rich fibrin in the management of soft tissue healing and pain in post-extraction sockets: A randomized clinical trial.

This study aimed to evaluate the clinical effect of leukocyte- and platelet-rich fibrin (L-PRF) to improve epithelialization and decrease postoperative pain in post-extraction sockets. Thirty two participants requiring extractions of posterior teeth were randomized into two groups: 1) extractions and socket filling with L-PRF membrane (test group) and 2) extraction with spontaneous healing (control group). One week after extraction, an assessment of soft tissue healing around the sockets was performed using the healing index. Also, postoperative pain by visual analog scale (VAS) and number of consumed analgesic tablets were recorded. In the first week, the sockets of the test group presented a significantly (mean of 3.81 ± 0.54; p = 0.0138) higher level of healing when compared to the sockets of the control group (mean of 3.18 ± 0.65). The participants of control group reported a significantly (mean of 5.12 ± 1.08; p = 0.0128) higher level of postoperative pain when compared to the test group (mean of 4 ± 1.15). Also, the control group consumed a greater number of analgesics (mean of 1.75 ± 0.85; p = 0.0136) when compared to the test group (mean of 1 ± 1.15). The results of the present study demonstrate that whenever improved healing of the extraction socket is needed, the use of L-PRF should be considered. In addition, the use of L-PRF decreases postoperative pain and discomfort.

Usefulness of platelet-rich fibrin as a hemostatic agent after dental extractions in patients receiving anticoagulant therapy with factor Xa inhibitors: a case series.

PURPOSE: To evaluate the clinical outcomes of platelet-rich fibrin (PRF) application for hemostasis after dental extraction in patients receiving anticoagulant therapy with factor Xa inhibitors. METHODS: In total, 25 patients receiving anticoagulant therapy with rivaroxaban or apixaban who required routine dental extraction were evaluated. In all patients, PRF was used for hemostasis in addition to adapting sutures. Bleeding was subjectively assessed using a sterilize gauze pad at 24, 48, and 72 h after the procedure. RESULTS: All invited participants (n = 25) consented to participate. The PRF clots successfully arrested bleeding after extraction in all patients, with no complications at any time point after the procedure. Favorable soft tissue healing was observed during suture removal at 10 days after the procedure in all patients, with no signs of infection or late healing. CONCLUSIONS: The results of this case series indicate that PRF is a promising natural hemostatic agent for the management of bleeding after dental extraction in patients receiving factor Xa inhibitor therapy. Further controlled clinical studies with larger patient samples are necessary to clarify the findings of this case series.

Anatomic evaluation of the incisive canal with cone beam computed tomography and its relevance to surgical procedures in the mental region: a retrospective study in a Brazilian population.

BACKGROUND AND OBJECTIVE: To evaluate the prevalence, location, length, diameter, and distances related to the incisive canal (IC) and the need for cone beam computed tomography (CBCT) as a complementary exam prior to surgery in the mental region. MATERIALS AND METHODS: One hundred CBCT images from patients of both genders aged 27 to 73 years were evaluated. At every 3 mm, the diameter (DIAM) of the right and left ICs and their location, their distance to base of the jaw (BIC), the buccal (BAIC) and lingual (LAIC) aspects, and their length were measured. RESULTS: The 100 patients comprised 50 men (50%) and 50 women (50%). The IC was detected in 78 patients, more frequently in women (80%) than in men (76%). Measurements were taken in millimeters. The mean measurements for the two sides and for men and women combined were as follows: BIC = 10.0, BAIC = 4.0, LAIC = 6.2, ICL = 19.9, and DIAM = 1.4. CONCLUSIONS: The measurements show the need for care from professionals when performing intraosseous surgical procedures in the mental region. The distances between the IC and the references studied must be observed. Thus, CBCT becomes essential for surgical planning in the mental region. CLINICAL RELEVANCE: The mental region of the mandible is considered a safe area to perform surgical procedures such as the placement of osseointegrated implants, orthognathic surgery, and the removal of bone grafts. However, this region includes important neurovascular structures that must be considered or else hemorrhage and neurologic disorders can be experienced.

The use of platelet-rich fibrin as a hemostatic material in oral soft tissues.

The control of postoperative bleeding represents one of the main intercurrent events associated with soft tissue surgical procedures in the oral cavity. In this context, platelet-rich fibrin (PRF) membranes are materials with great potential for optimizing soft tissue healing and induction of hemostasis. This interventional case series describes the treatment of 10 patients with excisional biopsy of benign oral cavity lesions, following a screening sequence at the surgery clinic of a Brazilian dental school between the years of 2015 and 2017. After treatment with PRF, patients presented mean time for postoperative hemostasis of 10.3 ± 2.5 s, requiring the average use of three membranes to cover the surgical area. The results suggest that the use of platelet-rich fibrin membranes may represent a feasible alternative hemostatic material for the treatment of oral lesions.