Comparison of Laser-Synthetized Nanographene-Based Electrodes for Flexible Supercapacitors.

In this paper, we present a comparative study of a cost-effective method for the mass fabrication of electrodes to be used in thin-film flexible supercapacitors. This technique is based on the laser-synthesis of graphene-based nanomaterials, specifically, laser-induced graphene and reduced graphene oxide. The synthesis of these materials was performed using two different lasers: a CO2 laser with an infrared wavelength of λ = 10.6 µm and a UV laser (λ = 405 nm). After the optimization of the parameters of both lasers for this purpose, the performance of these materials as bare electrodes for flexible supercapacitors was studied in a comparative way. The experiments showed that the electrodes synthetized with the low-cost UV laser compete well in terms of specific capacitance with those obtained with the CO2 laser, while the best performance is provided by the rGO electrodes fabricated with the CO2 laser. It has also been demonstrated that the degree of reduction achieved with the UV laser for the rGO patterns was not enough to provide a good interaction electrode-electrolyte. Finally, we proved that the specific capacitance achieved with the presented supercapacitors can be improved by modifying the in-planar structure, without compromising their performance, which, together with their compatibility with doping-techniques and surface treatments processes, shows the potential of this technology for the fabrication of future high-performance and inexpensive flexible supercapacitors.

Particle Segregation at Contact Lines of Evaporating Colloidal Drops: Influence of the Substrate Wettability and Particle Charge-Mass Ratio.

Segregation of particles during capillary/convective self-assembly is interesting for self-stratification in colloidal deposits. In evaporating drops containing colloidal particles, the wettability properties of substrate and the sedimentation of particles can affect their accumulation at contact lines. In this work we studied the size segregation and discrimination of charged particles with different densities. We performed in-plane particle counting at evaporating triple lines by using fluorescence confocal microscopy. We studied separately substrates with very different wettability properties and particles with different charge-mass ratios at low ionic strength. We used binary colloidal suspensions to compare simultaneously the deposition of two different particles. The particle deposition rate strongly depends on the receding contact angle of the substrate. We further observed a singular behavior of charged polystyrene particles in binary mixtures under "salt-free" conditions explained by the "colloidal Brazil nut" effect.

In-plane particle counting at contact lines of evaporating colloidal drops: effect of the particle electric charge.

Complete understanding of colloidal assembly is still a goal to be reached. In convective assembly deposition, the concentration gradients developed in evaporating drops or reservoirs are usually significant. However, collective diffusion of charge-stabilized particles has been barely explored. The balance between convective and diffusive flows may dictate the particle dynamics inside evaporating colloidal drops. In this work we performed in situ counting of fluorescent particles in the vicinity of the triple line of evaporating sessile drops by using confocal laser scanning microscopy. We used particles of different sizes, with different charge response over the pH scale and we focused on charged and nearly uncharged particles. Two substrates with different receding contact angles were used. Binary colloidal mixtures were used to illustrate simultaneously the accumulation of particles with two different charge states at the triple line. The deposition rate close to the triple line was different depending on the electric state of the particle, regardless of the substrate used.

Transition from stripe-like patterns to a particulate film using driven evaporating menisci.

Better control of colloidal assembly by convective deposition is particularly helpful in particle templating. However, knowledge of the different factors that can alter colloidal patterning mechanisms is still insufficient. Deposit morphology is strongly ruled by contact line dynamics, but the wettability properties of the substrate can alter it drastically. In this work, we experimentally examined the roles of substrate contact angle hysteresis and receding contact angle using driven evaporating menisci similar to the dip-coating technique but at a low capillary number. We used smooth substrates with very different wettability properties and nanoparticles of different sizes. For fixed withdrawal velocity, evaporation conditions, and nanoparticle concentration, we analyzed the morphology of the deposits formed on each substrate. A gradual transition from stripe-like patterns to a film was observed as the contact angle hysteresis and receding contact angle were lowered.