RESUMEN
Four-terminal (4-T) tandem solar cells (e.g., perovskite/CuInSe2 (CIS)) rely on three transparent conductive oxide electrodes with high mobility and low free carrier absorption in the near-infrared (NIR) region. In this work, a reproducible In2O3:H (IO:H) film deposition process is developed by independently controlling H2 and O2 gas flows during magnetron sputtering, yielding a high mobility value up to 129 cm2 V-1 s-1 in highly crystallized IO:H films annealed at 230 °C. Optimization of H2 and O2 partial pressures further decreases the crystallization temperature to 130 °C. By using a highly crystallized IO:H film as the front electrode in NIR-transparent perovskite solar cell (PSC), a 17.3% steady-state power conversion efficiency and an 82% average transmittance between 820 and 1300 nm are achieved. In combination with an 18.1% CIS solar cell, a 24.6% perovskite/CIS tandem device in 4-T configuration is demonstrated. Optical analysis suggests that an amorphous IO:H film (without postannealing) and a partially crystallized IO:H film (postannealed at 150 °C), when used as a rear electrode in a NIR-transparent PSC and a front electrode in a CIS solar cell, respectively, can outperform the widely used indium-doped zinc oxide (IZO) electrodes, leading to a 1.38 mA/cm2 short-circuit current (Jsc) gain in the bottom CIS cell of 4-T tandems.
RESUMEN
The possibility to manufacture perovskite solar cells (PSCs) at low temperatures paves the way to flexible and lightweight photovoltaic (PV) devices manufactured via high-throughput roll-to-roll processes. In order to achieve higher power conversion efficiencies, it is necessary to approach the radiative limit via suppression of non-radiative recombination losses. Herein, we performed a systematic voltage loss analysis for a typical low-temperature processed, flexible PSC in n-i-p configuration using vacuum deposited C60 as electron transport layer (ETL) and two-step hybrid vacuum-solution deposition for CH3NH3PbI3 perovskite absorber. We identified the ETL/absorber interface as a bottleneck in relation to non-radiative recombination losses, the quasi-Fermi level splitting (QFLS) decreases from ~1.23 eV for the bare absorber, just ~90 meV below the radiative limit, to ~1.10 eV when C60 is used as ETL. To effectively mitigate these voltage losses, we investigated different interfacial modifications via vacuum deposited interlayers (BCP, B4PyMPM, 3TPYMB, and LiF). An improvement in QFLS of ~30-40 meV is observed after interlayer deposition and confirmed by comparable improvements in the open-circuit voltage after implementation of these interfacial modifications in flexible PSCs. Further investigations on absorber/hole transport layer (HTL) interface point out the detrimental role of dopants in Spiro-OMeTAD film (widely employed HTL in the community) as recombination centers upon oxidation and light exposure.
RESUMEN
Prompted by the rapidly developing field of wearable electronics, research into biocompatible substrates and coatings is intensifying. Acrylate-based hydrogel polymers have gained widespread use as biocompatible articles in applications such as contact and intraocular lenses. Surface treatments and/or coatings present one strategy to further enhance the performance of these hydrogels or even realize novel functionality. In this study, the conductive polymer poly(3,4-ethylenedioxythiophene) (PEDOT) is deposited from the vapor phase onto hydrated hydrogel substrates and blended with biocompatibilizing coconstituents incorporating polyethylene glycol (PEG) and polydimethyl siloxane (PDMS) moieties. Plasma pretreatment of the dehydrated hydrogel substrate modifies its surface topography and chemical composition to facilitate the attachment of conductive PEDOT-based surface layers. Manipulating the vapor phase polymerization process and constituent composition, the PEDOT-based coating is engineered to be both hydrophilic (i.e. to promote biocompatibility) and highly conductive. The fabrication of this conductively coated hydrogel has implications for the future of wearable electronic devices.