RESUMEN
In this work, the analysis of environmental performance and its coherence with circular economy priorities of different variants of Al-ion battery construction was performed. Al-ion-based batteries can be considered as one of the future alternatives for currently used Li-ion-based cells when the shortage of lithium or cobalt becomes a challenge. All tested batteries were constructed with Al anodes, polypropylene foil separator, polyvinylidene fluoride + N-Methyl-2-pyrrolidone (PVDF+NMP) binder, Al collector and laminated Al foil pouch cell. WO3, Norit and carbon from potato starch (CPS) were used as a cathode material. Saturated solutions of AlCl3 dissolved in diethylene glycol dimethyl ether (DEG) and deep eutectic solvents (DES) originating from bacterial polymer polyhydroxyalkanoate were used as electrolytes. The ReCiPe impact assessment method was used in this analysis. The indicator in this study was ReCiPe Endpoint (H) V1.07 referring to Europe. SimaPro 9.4 software with Ecoinvent 3.8 inventory database were used for all calculations. The analysis included experimental production and assembly of batteries and their end-of-life processing. Based on the performed analysis it was found that the overall weighted impact of each single construction variant of an Al-ion battery is dominated by the use of electricity, no matter which variant is considered since it is related to the electricity mix in Poland and its high dependence on fossil fuels. Overall environmental impact is the smallest for CPS DEG battery, while Norit DEG and CPS DEG variants have slightly higher impacts. The share of end-of-life processing in overall environmental impacts of all analysed variants was found low compared to the Li-ion batteries. This observation indicates the Al-ion batteries as a promising direction of alternative electrochemical devices for energy storage systems while end-of-life processing and circular solution are concerned.
RESUMEN
In this study, the optimisation of a process for producing medium-chain-length polyhydroxyalkanoate (mcl-PHA) by Pseudomonas putida KT2440 when fed with a polyethene (PE)-derived fatty acid mixture was investigated. The PE was pyrolysed to produce a hydrocarbon wax that was subsequently oxidised to produce a mixture of fatty acids, purified, and used as a PHA substrate for the growth and selection of microorganisms. Based on the shaken flask screening, a production strain, i.e., Pseudomonas putida KT2440, was selected for conducting bioreactor studies. Feeding PE-derived fatty acids in a 20-L setup resulted in high mcl-PHA yields (83.0 g L-1 CDW with 65% PHA in 25 h). Furthermore, life-cycle assessment (LCA) was conducted to determine the environmental advantages of the proposed process and its impacts compared to those of other technologies for treating PE-derived waste streams. We conclude that processing waste PE into PHA, rather than incineration, produces biodegradable material while also reducing the additional emissions that arise from traditional PE waste treatment processes, such as incineration to gain energy.
Asunto(s)
Plásticos Biodegradables , Polihidroxialcanoatos , Pseudomonas putida , Biotecnología , PolietilenoRESUMEN
The main purpose of the article was to compare different scenarios of biopolymer production and their impacts on the environment using Life Cycle Assessment. Three alternative polyhydroxyalkanoates (PHA: amorphous PHA and poly(3-hydroxybutyrate), P(3HB)) production scenarios were considered to assess its environmental impact: Scenario A - Production of mcl-PHA/P(3HB) from crude vegetable oil; Scenario B - Production of P(3HB) with biodiesel by-product; Scenario C - Production of mcl-PHA/P(3HB) from used vegetable oil. Subject to the scenario considered, it was shown that the environmental efficiency of PHA production is highly dependent on carbon sources used, and it is strongly supporting production of mcl-PHA instead of P(3HB). As LCA study shows, due to low yield of P(3HB) in comparison to mcl-PHA production in considered processes, all the P(3HB) production scenarios have higher impacts than the production of mcl-PHA. Production processes based on bacterial fermentation had its impacts related mostly to the raw materials used and to its separation phase. Additionally, using secondary materials instead of raw ones, namely used oil instead of virgin oil, gives significant improvement with regard to environmental impact. The resource efficiency is also the identified as the key factor with sensitivity analysis that indicates the possible increase of biopolymer yield as the most beneficial factor. Biobased polymers have big environmental potential but still need significant improvement with regard to their manufacturing processes in order to become more economically benign. Preferably production of these microbial polymers should be integrated into biorefinery blocks, where such waste stream arises (e.g. biodiesel production plant).