Engineering Curcumin Biosynthesis in Poplar Affects Lignification and Biomass Yield.

Lignocellulosic biomass is recalcitrant toward deconstruction into simple sugars mainly due to the presence of lignin. By engineering plants to partially replace traditional lignin monomers with alternative ones, lignin degradability and extractability can be enhanced. Previously, the alternative monomer curcumin has been successfully produced and incorporated into lignified cell walls of Arabidopsis by the heterologous expression of DIKETIDE-CoA SYNTHASE (DCS) and CURCUMIN SYNTHASE2 (CURS2). The resulting transgenic plants did not suffer from yield penalties and had an increased saccharification yield after alkaline pretreatment. Here, we translated this strategy into the bio-energy crop poplar. Via the heterologous expression of DCS and CURS2 under the control of the secondary cell wall CELLULOSE SYNTHASE A8-B promoter (ProCesA8-B), curcumin was also produced and incorporated into the lignified cell walls of poplar. ProCesA8-B:DCS_CURS2 transgenic poplars, however, suffered from shoot-tip necrosis and yield penalties. Compared to that of the wild-type (WT), the wood of transgenic poplars had 21% less cellulose, 28% more matrix polysaccharides, 23% more lignin and a significantly altered lignin composition. More specifically, ProCesA8-B:DCS_CURS2 lignin had a reduced syringyl/guaiacyl unit (S/G) ratio, an increased frequency of p-hydroxyphenyl (H) units, a decreased frequency of p-hydroxybenzoates and a higher fraction of phenylcoumaran units. Without, or with alkaline or hot water pretreatment, the saccharification efficiency of the transgenic lines was equal to that of the WT. These differences in (growth) phenotype illustrate that translational research in crops is essential to assess the value of an engineering strategy for applications. Further fine-tuning of this research strategy (e.g., by using more specific promoters or by translating this strategy to other crops such as maize) might lead to transgenic bio-energy crops with cell walls more amenable to deconstruction without settling in yield.

Introducing curcumin biosynthesis in Arabidopsis enhances lignocellulosic biomass processing.

Lignin is the main cause of lignocellulosic biomass recalcitrance to industrial enzymatic hydrolysis. By partially replacing the traditional lignin monomers by alternative ones, lignin extractability can be enhanced. To design a lignin that is easier to degrade under alkaline conditions, curcumin (diferuloylmethane) was produced in the model plant Arabidopsis thaliana via simultaneous expression of the turmeric (Curcuma longa) genes DIKETIDE-CoA SYNTHASE (DCS) and CURCUMIN SYNTHASE 2 (CURS2). The transgenic plants produced a plethora of curcumin- and phenylpentanoid-derived compounds with no negative impact on growth. Catalytic hydrogenolysis gave evidence that both curcumin and phenylpentanoids were incorporated into the lignifying cell wall, thereby significantly increasing saccharification efficiency after alkaline pretreatment of the transgenic lines by 14-24% as compared with the wild type. These results demonstrate that non-native monomers can be synthesized and incorporated into the lignin polymer in plants to enhance their biomass processing efficiency.

Degradation of lignin ß-aryl ether units in Arabidopsis thaliana expressing LigD, LigF and LigG from Sphingomonas paucimobilis SYK-6.

Lignin is a major polymer in the secondary plant cell wall and composed of hydrophobic interlinked hydroxyphenylpropanoid units. The presence of lignin hampers conversion of plant biomass into biofuels; plants with modified lignin are therefore being investigated for increased digestibility. The bacterium Sphingomonas paucimobilis produces lignin-degrading enzymes including LigD, LigF and LigG involved in cleaving the most abundant lignin interunit linkage, the ß-aryl ether bond. In this study, we expressed the LigD, LigF and LigG (LigDFG) genes in Arabidopsis thaliana to introduce postlignification modifications into the lignin structure. The three enzymes were targeted to the secretory pathway. Phenolic metabolite profiling and 2D HSQC NMR of the transgenic lines showed an increase in oxidized guaiacyl and syringyl units without concomitant increase in oxidized ß-aryl ether units, showing lignin bond cleavage. Saccharification yield increased significantly in transgenic lines expressing LigDFG, showing the applicability of our approach. Additional new information on substrate specificity of the LigDFG enzymes is also provided.

Introduction of chemically labile substructures into Arabidopsis lignin through the use of LigD, the Cα-dehydrogenase from Sphingobium sp. strain SYK-6.

Bacteria-derived enzymes that can modify specific lignin substructures are potential targets to engineer plants for better biomass processability. The Gram-negative bacterium Sphingobium sp. SYK-6 possesses a Cα-dehydrogenase (LigD) enzyme that has been shown to oxidize the α-hydroxy functionalities in ß-O-4-linked dimers into α-keto analogues that are more chemically labile. Here, we show that recombinant LigD can oxidize an even wider range of ß-O-4-linked dimers and oligomers, including the genuine dilignols, guaiacylglycerol-ß-coniferyl alcohol ether and syringylglycerol-ß-sinapyl alcohol ether. We explored the possibility of using LigD for biosynthetically engineering lignin by expressing the codon-optimized ligD gene in Arabidopsis thaliana. The ligD cDNA, with or without a signal peptide for apoplast targeting, has been successfully expressed, and LigD activity could be detected in the extracts of the transgenic plants. UPLC-MS/MS-based metabolite profiling indicated that levels of oxidized guaiacyl (G) ß-O-4-coupled dilignols and analogues were significantly elevated in the LigD transgenic plants regardless of the signal peptide attachment to LigD. In parallel, 2D NMR analysis revealed a 2.1- to 2.8-fold increased level of G-type α-keto-ß-O-4 linkages in cellulolytic enzyme lignins isolated from the stem cell walls of the LigD transgenic plants, indicating that the transformation was capable of altering lignin structure in the desired manner.

Metabolic engineering of novel lignin in biomass crops.

Lignin, a phenolic polymer in the secondary wall, is the major cause of lignocellulosic biomass recalcitrance to efficient industrial processing. From an applications perspective, it is desirable that second-generation bioenergy crops have lignin that is readily degraded by chemical pretreatments but still fulfill its biological role in plants. Because plants can tolerate large variations in lignin composition, often without apparent adverse effects, substitution of some fraction of the traditional monolignols by alternative monomers through genetic engineering is a promising strategy to tailor lignin in bioenergy crops. However, successful engineering of lignin incorporating alternative monomers requires knowledge about phenolic metabolism in plants and about the coupling properties of these alternative monomers. Here, we review the current knowledge about lignin biosynthesis and the pathways towards the main phenolic classes. In addition, the minimal requirements are defined for molecules that, upon incorporation into the lignin polymer, make the latter more susceptible to biomass pretreatment. Numerous metabolites made by plants meet these requirements, and several have already been tested as monolignol substitutes in biomimetic systems. Finally, the status of detection and identification of compounds by phenolic profiling is discussed, as phenolic profiling serves in pathway elucidation and for the detection of incorporation of alternative lignin monomers.