RESUMEN
PURPOSE: In this study, the shear bond strengths (SBS) of luting cements to fixed superstructure metal surfaces under various seating forces were investigated. MATERIALS AND METHODS: Seven different cements [Polycarboxylate (PCC), Glass-Ionomer (GIC), Zinc phospahate (ZPC), Self-adhesive resin (RXU), Resin (C&B), and Temporary cements ((RXT) and (TCS))] were bonded to a total number of 224 square blocks (5×5×3 mm) made of one pure metal [Titanium (CP Ti) and two metal alloys [Gold-Platinum (Au-Pt) and Cobalt-Chrome (Co-Cr)] under 10 N and 50 N seating forces. SBS values were determined and data were analyzed with 3-way ANOVA. Pairwise comparisons and interactions among groups were analyzed with Tukey's simultaneous confidence intervals. RESULTS: Overall mean scores indicated that Co-Cr showed the highest SBS values (1.96±0.4) (P<.00), while Au-Pt showed the lowest among all metals tested (1.57±0.4) (P<.00). Except for PCC/CP Ti, RXU/CP Ti, and GIC/Au-Pt factor level combinations (P<.00), the cements tested under 10 N seating force showed no significantly higher SBS values when compared to the values of those tested under 50 N seating force (P>.05). The PCC cement showed the highest mean SBS score (3.59±0.07) among all cements tested (P<.00), while the resin-based temporary luting cement RXT showed the lowest (0.39±0.07) (P<.00). CONCLUSION: Polycarboxylate cement provides reliable bonding performance to metal surfaces. Resin-based temporary luting cements can be used when retrievability is needed. GIC is not suitable for permanent cementation of fixed dental prostheses consisting of CP Ti or Au-Pt substructures.
RESUMEN
PURPOSE: The aim of this study was to evaluate the effect of thickness of zirconia on curing efficiency of resin cements. MATERIALS AND METHODS: Four discs with 4.0 mm in diameter were prepared from non-HIP translucent zirconia blocks using a CAD/CAM system and feldspathic ceramic was layered onto discs. Thus, 4 ceramic disc samples were fabricated: (G) 0.5 mm zirconia- as a control group, (G1) 0.5 mm zirconia and 0.5 mm feldspathic, (G2) 1.0 mm zirconia and 0.5 mm feldspathic and (G3) 2.0 mm zirconia and 0.5 mm feldspathic ceramic layer. 2 different dual cure cements were polymerized using a LED curing unit. Degree of conversion was evaluated using Vickers Hardness Test and depths of cure of samples were measured. Data were analyzed statistically using One-way ANOVA and Tukey's HSD test (p<0.05). RESULTS: Microhardness and depth of cure values were different under same thickness of ceramic discs for two resin cements. As the thickness of the zirconia discs increased, the microhardness values and depth of cure decreased. CONCLUSION: Photocuring time cannot be the same for all clinical conditions, under thicker zirconia restorations (>2.0 mm), an extended period of light curing or a light unit with a high irradiance should be used.
RESUMEN
PURPOSE: Adequate polymerization is a crucial factor in obtaining optimal physical properties and a satisfying clinical performance from composite resin materials. The aim of this study was to evaluate the polymerization efficiency of dual-cure resin cement cured with two different light curing units under zirconia structures having differing thicknesses. MATERIALS AND METHODS: 4 zirconia discs framework in 4 mm diameter and in 0.5 mm, 1 mm and 1.5 mm thickness were prepared using computer-aided design system. One of the 0.5 mm-thick substructures was left as mono-layered whereas others were layered with feldspathic porcelain of same thickness and ceramic samples with 4 different thicknesses (0.5, 1, 1.5 and 2.0 mm) were prepared. For each group (n=12) resin cement was light cured in polytetrafluoroethylene molds using Light Emitting Diode (LED) or Quartz-Tungsten Halogen (QHT) light curing units under each of 4 zirconia based discs (n=96). The values of depth of cure (in mm) and the Vickers Hardness Number values (VHN) were evaluated for each specimen. RESULTS: The use of LED curing unit produced a greater depth of cure compared to QTH under ceramic discs with 0.5 and 1 mm thickness (p<0.05).At 100µm and 300 µm depth, the LED unit produced significantly greater VHN values compared to the QTH unit (p<0.05). At 500 µm depth, the difference between the VHN values of LED and QTH groups were not statistically significant. CONCLUSION: Light curing may not result in adequate resin cement polymerization under thick zirconia structures. LED light sources should be preferred over QTH for curing dual-cure resin cements, especially for those under thicker zirconia restorations.