Detection and identification of single ribonucleotide monophosphates using a dual in-plane nanopore sensor made in a thermoplastic via replication.

We report the generation of ∼8 nm dual in-plane pores fabricated in a thermoplastic via nanoimprint lithography (NIL). These pores were connected in series with nanochannels, one of which served as a flight tube to allow the identification of single molecules based on their molecular-dependent apparent mobilities (i.e., dual in-plane nanopore sensor). Two different thermoplastics were investigated including poly(methyl methacrylate), PMMA, and cyclic olefin polymer, COP, as the substrate for the sensor both of which were sealed using a low glass transition cover plate (cyclic olefin co-polymer, COC) that could be thermally fusion bonded to the PMMA or COP substrate at a temperature minimizing nanostructure deformation. Unique to these dual in-plane nanopore sensors was two pores flanking each side of the nanometer flight tube (50 × 50 nm, width × depth) that was 10 µm in length. The utility of this dual in-plane nanopore sensor was evaluated to not only detect, but also identify single ribonucleotide monophosphates (rNMPs) by using the travel time (time-of-flight, ToF), the resistive pulse event amplitude, and the dwell time. In spite of the relatively large size of these in-plane pores (∼8 nm effective diameter), we could detect via resistive pulse sensing (RPS) single rNMP molecules at a mass load of 3.9 fg, which was ascribed to the unique structural features of the nanofluidic network and the use of a thermoplastic with low relative dielectric constants, which resulted in a low RMS noise level in the open pore current. Our data indicated that the identification accuracy of individual rNMPs was high, which was ascribed to an improved chromatographic contribution to the nano-electrophoresis apparent mobility. With the ToF data only, the identification accuracy was 98.3%. However, when incorporating the resistive pulse sensing event amplitude and dwell time in conjunction with the ToF and analyzed via principal component analysis (PCA), the identification accuracy reached 100%. These findings pave the way for the realization of a novel chip-based single-molecule RNA sequencing technology.

Nano-injection molding with resin mold inserts for prototyping of nanofluidic devices for single molecular detection.

While injection molding is becoming the fabrication modality of choice for high-scale production of microfluidic devices, especially those used for in vitro diagnostics, its translation into the growing area of nanofluidics (structures with at least one dimension <100 nm) has not been well established. Another prevailing issue with injection molding is the high startup costs and the relatively long time between device iterations making it in many cases impractical for device prototyping. We report, for the first time, functional nanofluidic devices with dimensions of critical structures below 30 nm fabricated by injection molding for the manipulation, identification, and detection of single molecules. UV-resin molds replicated from Si masters served as mold inserts, negating the need for generating Ni-mold inserts via electroplating. Using assembled devices with a cover plate via hybrid thermal fusion bonding, we demonstrated two functional thermoplastic nanofluidic devices. The first device consisted of dual in-plane nanopores placed at either end of a nanochannel and was used to detect and identify single ribonucleotide monophosphate molecules via resistive pulse sensing and obtain the effective mobility of the molecule through nanoscale electrophoresis to allow its identification. The second device demonstrated selective binding of a single RNA molecule to a solid phase bioreactor decorated with a processive exoribonuclease, XRN1. Our results provide a simple path towards the use of injection molding for device prototyping in the development stage of any nanofluidic or even microfluidic application, through which rapid scale-up is made possible by transitioning from prototyping to high throughput production using conventional Ni mold inserts.

High Sensitivity Extended Nano-Coulter Counter for Detection of Viral Particles and Extracellular Vesicles.

We present a chip-based extended nano-Coulter counter (XnCC) that can detect nanoparticles affinity-selected from biological samples with low concentration limit-of-detection that surpasses existing resistive pulse sensors by 2-3 orders of magnitude. The XnCC was engineered to contain 5 in-plane pores each with an effective diameter of 350 nm placed in parallel and can provide high detection efficiency for single particles translocating both hydrodynamically and electrokinetically through these pores. The XnCC was fabricated in cyclic olefin polymer (COP) via nanoinjection molding to allow for high-scale production. The concentration limit-of-detection of the XnCC was 5.5 × 103 particles/mL, which was a 1,100-fold improvement compared to a single in-plane pore device. The application examples of the XnCC included counting affinity selected SARS-CoV-2 viral particles from saliva samples using an aptamer and pillared microchip; the selection/XnCC assay could distinguish the COVID-19(+) saliva samples from those that were COVID-19(-). In the second example, ovarian cancer extracellular vesicles (EVs) were affinity selected using a pillared chip modified with a MUC16 monoclonal antibody. The affinity selection chip coupled with the XnCC was successful in discriminating between patients with high grade serous ovarian cancer and healthy donors using blood plasma as the input sample.

Engineering inlet structures to enhance DNA capture into nanochannels in a polymer nanofluidic device produced via nanoimprint lithography.

Operating nanofluidic biosensors requires threading single molecules to be analyzed from microfluidic networks into nanostructures, mostly nanochannels or nanopores. Different inlet structures have been employed as a means of enhancing the number of the capture events into nanostructures. Here, we systematically investigated the effects of various engineered inlet structures formed at the micro/nanochannel interface on the capture of single λ-DNA molecules into the nanochannels. Different inlet geometries were evaluated and ranked in order of their effectiveness. Adding an inlet structure prior to a nanochannel effectively improved the DNA capture rate by 190 - 700 % relative to that for the abrupt micro/nanochannel interface. The capture of DNA from the microchannel to various inlets was determined mainly by the capture volumes of the inlet structures and the geometrically modified electric field in the inlet structure. However, as the width of the inlet structure increased, the hydrodynamic flow existing in the microchannel negatively influenced the DNA capture by dragging some DNA molecules deep into the inlet structure back to the microchannel. Our results indicate that engineering inlet structures is an effective means of controlling the capture of DNA molecules into nanostructures, which is important for operation of nanofluidic biosensors.

Nanofluidic devices for the separation of biomolecules.

Over the last 30-years, microchip electrophoresis and its applications have expanded due to the benefits it offers. Nanochip electrophoresis, on the other hand, is viewed as an evolving area of electrophoresis because it offers some unique advantages not associated with microchip electrophoresis. These advantages arise from unique phenomena that occur in the nanometer domain not readily apparent in the microscale domain due to scale-dependent effects. Scale-dependent effects associated with nanochip electrophoresis includes high surface area-to-volume ratio, electrical double layer overlap generating parabolic flow even for electrokinetic pumping, concentration polarization, transverse electromigration, surface charge dominating flow, and surface roughness. Nanochip electrophoresis devices consist of channels with dimensions ranging from 1 to 1000 nm including classical (1-100 nm) and extended (100 nm - 1000 nm) nanoscale devices. In this review, we highlight scale-dependent phenomena associated with nanochip electrophoresis and the utilization of those phenomena to provide unique biomolecular separations that are not possible with microchip electrophoresis. We will also review the range of materials used for nanoscale separations and the implication of material choice for the top-down fabrication and operation of these devices. We will also provide application examples of nanochip electrophoresis for biomolecule separations with an emphasis on nano-electrophoresis (nEP) and nano-electrochromatography (nEC).

Microfluidic affinity selection of active SARS-CoV-2 virus particles.

We report a microfluidic assay to select active severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) viral particles (VPs), which were defined as intact particles with an accessible angiotensin-converting enzyme 2 receptor binding domain (RBD) on the spike (S) protein, from clinical samples. Affinity selection of SARS-CoV-2 particles was carried out using injection molded microfluidic chips, which allow for high-scale production to accommodate large-scale screening. The microfluidic contained a surface-bound aptamer directed against the virus's S protein RBD to affinity select SARS-CoV-2 VPs. Following selection (~94% recovery), the VPs were released from the chip's surface using a blue light light-emitting diode (89% efficiency). Selected SARS-CoV-2 VP enumeration was carried out using reverse transcription quantitative polymerase chain reaction. The VP selection assay successfully identified healthy donors (clinical specificity = 100%) and 19 of 20 patients with coronavirus disease 2019 (COVID-19) (95% sensitivity). In 15 patients with COVID-19, the presence of active SARS-CoV-2 VPs was found. The chip can be reprogrammed for any VP or exosomes by simply changing the affinity agent.

Fluidic operation of a polymer-based nanosensor chip for analysing single molecules.

Most medical diagnostic tests are expensive, involve slow turnaround times from centralized laboratories and require highly specialized equipment with seasoned technicians to carry out the assay. To facilitate realization of precision medicine at the point of care, we have developed a mixed-scale nanosensor chip featuring high surface area pillar arrays where solid-phase reactions can be performed to detect and identify nucleic acid targets found in diseased patients. Products formed can be identified and detected using a polymer nanofluidic channel. To guide delivery of this platform, we discuss the operation of various components of the device and simulations (COMSOL) used to guide the design by investigating parameters such as pillar array loading, and hydrodynamic and electrokinetic flows. The fabrication of the nanosensor is discussed, which was performed using a silicon (Si) master patterned with a combination of focused ion beam milling and photolithography with deep reactive ion etching. The mixed-scale patterns were transferred into a thermoplastic via thermal nanoimprint lithography, which facilitated fabrication of the nanosensor chip making it appropriate for in vitro diagnostics. The results from COMSOL were experimentally verified for hydrodynamic flow using Rhodamine B as a fluorescent tracer and electrokinetic flow using single fluorescently labelled oligonucleotides (single-stranded DNAs, ssDNAs).

In-plane Extended Nano-coulter Counter (XnCC) for the Label-free Electrical Detection of Biological Particles.

We report an in-plane extended nanopore Coulter counter (XnCC) chip fabricated in a thermoplastic via imprinting. The fabrication of the sensor utilized both photolithography and focused ion beam milling to make the microfluidic network and the in-plane pore sensor, respectively, in Si from which UV resin stamps were generated followed by thermal imprinting to produce the final device in the appropriate plastic (cyclic olefin polymer, COP). As an example of the utility of this in-plane extended nanopore sensor, we enumerated SARS-CoV-2 viral particles (VPs) affinity-selected from saliva and extracellular vesicles (EVs) affinity-selected from plasma samples secured from mouse models exposed to different ionizing radiation doses.

Modifying surface charge density of thermoplastic nanofluidic biosensors by multivalent cations within the slip plane of the electric double layer.

Thermoplastic nanofluidic devices are promising platforms for sensing single biomolecules due to their mass fabrication capability. When the molecules are driven electrokinetically through nanofluidic networks, surface charges play a significant role in the molecular capture and transportation, especially when the thickness of the electrical double layer is close to the dimensions of the nanostructures in the device. Here, we used multivalent cations to alter the surface charge density of thermoplastic nanofluidic devices. The surface charge alteration was done by filling the device with a multivalent ionic solution, followed by withdrawal of the solution and replacing it with KCl for conductance measurement. A systematic study was performed using ionic solutions containing Mg2+ and Al3+ for nanochannels made of three polymers: poly(ethylene glycol) diacrylate (PEGDA), poly(methyl methacrylate) (PMMA) and cyclic olefin copolymer (COC). Overall, multivalent cations within the slip plane decreased the effective surface charge density of the device surface and the reduction rate increased with the cation valency, cation concentration and the surface charge density of thermoplastic substrates. We demonstrated that a 10-nm diameter in-plane nanopore formed in COC allowed translocation of λ-DNA molecules after Al3+ modification, which is attributed to the deceased viscous drag force in the nanopore by the decreased surface charge density. This work provides a general method to manipulate surface charge density of nanofluidic devices for biomolecule resistive pulse sensing. Additionally, the experimental results support ion-ion correlations as the origin of charge inversion over specific chemical adsorption.

Label-Free Identification of Single Mononucleotides by Nanoscale Electrophoresis.

Nanoscale electrophoresis allows for unique separations of single molecules, such as DNA/RNA nucleobases, and thus has the potential to be used as single molecular sensors for exonuclease sequencing. For this to be envisioned, label-free detection of the nucleotides to determine their electrophoretic mobility (i.e., time-of-flight, TOF) for highly accurate identification must be realized. Here, for the first time a novel nanosensor is shown that allows discriminating four 2-deoxyribonucleoside 5'-monophosphates, dNMPs, molecules in a label-free manner by nanoscale electrophoresis. This is made possible by positioning two sub-10 nm in-plane pores at both ends of a nanochannel column used for nanoscale electrophoresis and measuring the longitudinal transient current during translocation of the molecules. The dual nanopore TOF sensor with 0.5, 1, and 5 µm long nanochannel column lengths discriminates different dNMPs with a mean accuracy of 55, 66, and 94%, respectively. This nanosensor format can broadly be applicable to label-free detection and discrimination of other single molecules, vesicles, and particles by changing the dimensions of the nanochannel column and in-plane nanopores and integrating different pre- and postprocessing units to the nanosensor. This is simple to accomplish because the nanosensor is contained within a fluidic network made in plastic via replication.

Tailoring Thermoplastic In-Plane Nanopore Size by Thermal Fusion Bonding for the Analysis of Single Molecules.

We report a simple method for tailoring the size of in-plane nanopores fabricated in thermoplastics for single-molecule sensing. The in-plane pores were fabricated via nanoimprint lithography (NIL) from resin stamps, which were generated from Si masters. We could reduce the size of the in-plane nanopores from 30 to ∼10 nm during the thermal fusion bonding (TFB) step, which places a cover plate over the imprinted polymer substrate under a controlled pressure and temperature to form the relevant nanofluidic devices. Increased pressures during TFB caused the cross-sectional area of the in-plane pore to be reduced. The in-plane nanopores prepared with different TFB pressures were utilized to detect single-λ-DNA molecules via resistive pulse sensing, which showed a higher current amplitude in devices bonded at higher pressures. Using this method, we also show the ability to tune the pore size to detect single-stranded (ss) RNA molecules and single ribonucleotide adenosine monophosphate (rAMP). However, due to the small size of the pores required for detection of the ssRNA and rAMPs, the surface charge arising from carboxylate groups generated during O2 plasma oxidation of the surfaces of the nanopores to make them wettable had to be reduced to allow translocation of coions. This was accomplished using EDC/NHS coupling chemistry and ethanolamine. This simple modification chemistry increased the event frequency from ∼1 s-1 to >136 s-1 for an ssRNA concentration of 100 nM.

Thermoplastic nanofluidic devices for identifying abasic sites in single DNA molecules.

DNA damage can take many forms such as double-strand breaks and/or the formation of abasic (apurinic/apyrimidinic; AP) sites. The presence of AP sites can be used to determine therapeutic efficacy of many drugs, such as doxorubicin. While there are different assays to search for DNA damage, they are fraught with limitations, such as the need for large amounts of DNA secured from millions of cells. This is challenging due to the growing importance of using liquid biopsies as a source of biomarkers for many in vitro diagnostic assays. To accommodate the mass limits imposed by the use of liquid biopsies, we report a single-molecule DNA damage assay that uses plastic nanofluidic chips to stretch DNA to near its full contour length when the channel dimensions (width and depth) are near the persistence length (∼50 nm) of double-stranded (ds) DNA. The nanofluidic chip consisted of input funnels for high loading efficiency of single DNA molecules, entropic traps to store the DNA and simultaneously load a series of nanochannels for high throughput processing, and an array of stretching nanochannels to read the AP sites. Single dsDNA molecules, which were labeled with an intercalating dye and a biotinylated aldehyde reactive probe (bARP), could be parked in the stretching nanochannels, where the AP sites were read directly using a dual-color fluorescence microscope equipped with an EMCCD camera. One color of the microscope was used to read the DNA length and the second color detected the AP sites. The nanofluidic chip was made from thermoplastics via nanoimprint lithography, which obviated the need for direct writing the devices in glass or quartz using focused ion beam milling. We show that we can read the frequency of AP sites in single dsDNA molecules with the frequency of AP sites determined by associating fluorescently-labeled streptavidin with bARP through a biotin/streptavidin complex.

Electrokinetic identification of ribonucleotide monophosphates (rNMPs) using thermoplastic nanochannels.

With advances in the design and fabrication of nanofluidic devices during the last decade, there have been a few reports on nucleic acid analysis using nanoscale electrophoresis. The attractive nature of nanofluidics is the unique phenomena associated with this length scale that are not observed using microchip electrophoresis. Many of these effects are surface-related and include electrostatics, surface roughness, van der Waals interactions, hydrogen bonding, and the electric double layer. The majority of reports related to nanoscale electrophoresis have utilized glass-based devices, which are not suitable for broad dissemination into the separation community because of the sophisticated, time consuming, and high-cost fabrication methods required to produce the relevant devices. In this study, we report the use of thermoplastic nanochannels (110 nm x 110 nm, depth x width) for the free solution electrokinetic analysis of ribonucleotide monophosphates (rNMPs). Thermoplastic devices with micro- and nanofluidic networks were fabricated using nanoimprint lithography (NIL) with the structures enclosed via thermal fusion bonding of a cover plate to the fluidic substrate. Unique to this report is that we fabricated devices in cyclic olefin copolymer (COC) that was thermally fusion bonded to a COC cover plate. Results using COC/COC devices were compared to poly(methyl methacrylate), PMMA, devices with a COC cover plate. Our results indicated that at pH = 7.9, the electrophoresis in free solution resulted in an average resolution of the rNMPs >4 (COC/COC device range = 1.94 - 8.88; PMMA/COC device range = 1.4 - 7.8) with some of the rNMPs showing field-dependent electrophoretic mobilities. Baseline separation of the rNMPs was not possible using PMMA- or COC-based microchip electrophoresis. We also found that COC/COC devices could be assembled and UV/O3 activated after device assembly with the dose of the UV/O3 affecting the magnitude of the electroosmotic flow, EOF. In addition, the bond strength between the substrate and cover plate of unmodified COC/COC devices was higher compared to PMMA/COC devices. The large differences in the electrophoretic mobilities of the rNMPs afforded by nanoscale electrophoresis will enable a new single-molecule sequencing platform we envision, which uses molecular-dependent electrophoretic mobilities to identify the constituent rNMPs generated from an intact RNA molecule using a processive exonuclease. With optimized nanoscale electrophoresis, the rNMPs could be identified via mobility matching at an accuracy >99% in both COC/COC and PMMA/COC devices.

Robust, transparent, superhydrophobic coatings using novel hydrophobic/hydrophilic dual-sized silica particles.

HYPOTHESIS: The superhydrophobic lotus leaf has dual-scale surface structures, that is, nano-bumps on micro-mountains. Large hydrophilic particles, due to its high surface energy and weight, have high affility to substrates and tend to precipitate at the bottom of coating films. Small hydrophobic particles, due to its low surface energy and weight, tends to sit on the top of coating films and form porous structures. To mimic the lotus leaf surface, it may be possible to develop dual-sized particle films, in which small particles are decorated on large particles. EXPERIMENTS: A one-step spin coating of a mixture of dual-sized silica particles (55/200 nm) was used. Epoxy resin was added to improve the adhesion of particle films. The single-sized and dual-sized particle films were compared. The mechanical robustness of particle films was tested by tape peeling and droplet impact. FINDINGS: The novel combination of hydrophobic silica (55 nm) and hydrophilic silica (200 nm) is essential in creating the hierarchical structures. By combining the strong adhesion of hydrophilic silica (bottom of coating film) to polymer substrates and porous structures of hydrophobic silica (top of coating film), we first time report a one-step and versatile approach to create uniform, transparent, robust, and superhydrophobic surface.

Open-tubular nanoelectrochromatography (OT-NEC): gel-free separation of single stranded DNAs (ssDNAs) in thermoplastic nanochannels.

Electrophoresis or electrochromatography carried out in nanometer columns (width and depth) offers some attractive benefits compared to microscale columns. These advantages include unique separation mechanisms that are scale dependent, fast separation times, and simpler workflow due to the lack of a need for column packing and/or wall coatings to create a stationary phase. We report the use of thermoplastics, in this case PMMA, as the substrate for separating single-stranded DNAs (ssDNAs). Electrophoresis nanochannels were created in PMMA using nanoimprint lithography (NIL), which can produce devices at lower cost and in a higher production mode compared to the fabrication techniques required for glass devices. The nanochannel column in PMMA was successful in separating ssDNAs in free solution that was not possible using microchip electrophoresis in PMMA. The separation could be performed in <1 s with resolution >1.5 when carried out using at an electric field strength of 280 V/cm and an effective column length of 60 µm (100 nm × 100 nm, depth and width). The ssDNAs transport through the PMMA column was driven electrokinetically under the influence of an EOF. The results indicated that the separation was dominated by chromatographic effects using an open tubular nano-electrochromatography (OT-NEC) mode of separation. Interesting to these separations was that no column packing was required nor a wall coating to create the stationary phase; the separation was affected using the native polymer that was UV/O3 activated and an aqueous buffer mobile phase.

Scalable fabrication of sub-10 nm polymer nanopores for DNA analysis.

We present the first fabrication of sub-10 nm nanopores in freestanding polymer membranes via a simple, cost-effective, high-throughput but deterministic fabrication method. Nanopores in the range of 10 nm were initially produced via a single-step nanoimprinting process, which was further reduced to sub-10 nm pores via a post-NIL polymer reflow process. The low shrinkage rate of 2.7 nm/min obtained under the conditions used for the reflow process was the key to achieving sub-10 nm pores with a controllable pore size. The fabricated SU-8 nanopore membranes were successfully employed for transient current measurements during the translocation of DNA molecules through the nanopores.

Nanohole array plasmonic biosensors: Emerging point-of-care applications.

Point-of-care (POC) applications have expanded hugely in recent years and is likely to continue, with an aim to deliver cheap, portable, and reliable devices to meet the demands of healthcare industry. POC devices are designed, prototyped, and assembled using numerous strategies but the key essential features that biosensing devices require are: (1) sensitivity, (2) selectivity, (3) specificity, (4) repeatability, and (5) good limit of detection. Overall the fabrication and commercialization of the nanohole array (NHA) setup to the outside world still remains a challenge. Here, we review the various methods of NHA fabrication, the design criteria, the geometrical features, the effects of surface plasmon resonance (SPR) on sensing as well as current state-of-the-art of existing NHA sensors. This review also provides easy-to-understand examples of NHA-based POC biosensing applications, its current status, challenges, and future prospects.

Patterned electromagnetic alignment of magnetic nanowires.

A combination of electromagnetic alignment and topological pattern assisted alignment to position magnetic nanowires, which is referred to as the Patterned Electromagnetic Alignment (PEA), is developed and examined. Electrodeposited, FeNiCo nanowires with different lengths were used as the test nanomaterial, and the microscale grooved surface was formed by UV nanoimprint lithography. The accuracy of the PEA with FeNiCo nanowires was evaluated by measuring the deviation angle from the direction of the magnetic field line for different magnetic field strengths and nanowire lengths, and a statistical alignment distribution was reported for different nanowire length groups. The results were compared with those of the electromagnetic alignment on flat surfaces and in grooved-patterned substrates without electromagnetic alignment. Overall, the deviation angle for the PEA was lower than that for the electromagnetic alignment when all other experimental conditions were identical, indicating that the alignment accuracy along the direction of the magnetic field lines was enhanced in the presence of surface micro grooves. This can be attributed to the fact that, upon attachment of nanowires to the substrate surface, the surface micro grooves in the PEA add additional deterministic characteristics to the otherwise stochastic nature of the nanowire deposition and solvent evaporation processes compared to the sole electromagnetic alignment.

Droplet Impinging Behavior on Surfaces with Wettability Contrasts.

Heterogeneous substrates with moderate and extreme wettability contrasts were fabricated by comprising of superhydrophobic/hydrophilic and superhydrophobic/extremely hydrophilic surfaces, respectively. The interactions of water droplets impinging on the surfaces with sharp wettability contrasts were investigated experimentally. The impinging droplets that slightly touch the hydrophilic or extremely hydrophilic areas on each substrate exhibit a directional rebounding towards the more wetting surfaces, i.e., hydrophilic or extremely hydrophilic surface. The trajectory and landing distance of the rebounded droplets were tailored by controlling the releasing height of the droplet, wetting contrast across the border, and portion of the droplet touching the more wetting surface of the substrates with wettability contrasts. The landing distance of the droplet increases with the increased releasing height and higher wettability contrast across the border. Increasing the portion of the impinging droplet touching the more wetting surface of the heterogeneous substrates leads to the shorter landing distance of rebounded droplets.

Surface Charge Density-Dependent DNA Capture through Polymer Planar Nanopores.

Surface charge density of nanopore walls plays a critical role in DNA capture in nanopore-based sensing platforms. This paper studied the effect of surface charge density on the capture of double-stranded (ds) DNA molecules into a polymer planar nanopore numerically and experimentally. First, we simulated the effective driving force ( Feff) for the translocation of a dsDNA through a planar nanopore with different sizes and surface charge densities. Focus was given on the capture stage from the nanopore mouth into the nanopore by placing a rodlike DNA at the nanopore mouth rather than inside the nanopore. For negatively charged DNA and nanopore walls, electrophoretic driving force ( FEP) under an electric field is opposed by the viscous drag force by electroosmotic flow ( FEOF). As the surface charge density of the nanopore wall becomes more negative, FEOF exceeds FEP beyond a threshold surface charge density, σthreshold, where DNA molecules cannot be driven through the nanopore via electrophoretic motion. For a 10 nm diameter nanopore filled with 1× TE buffer, σthreshold was determined to be -50 mC/m2. The simulation results were verified by performing dsDNA translocation experiments using a planar nanopore with 10 nm equivalent diameter imprinted on three polymer substrates with different surface charge densities. Both fluorescence observation and ionic current measurement confirmed that only nanopore devices with the surface charge density less negative than σthreshold allowed DNA translocation, indicating that the simulated σthreshold value can be used as a parameter to estimate the translocation of biopolymers in the design of nanopore devices.