RESUMEN
The aim of the study was to investigate the combined effect of the manufacturing process followed by HPP treatment on the inactivation of Salmonella spp. in artificially contaminated coppa samples, in order to verify the ability of the combined processes to achieve the objective of a 5-log reduction of Salmonella spp. needed for exportation to the U.S. Fresh anatomical cuts intended for coppa production were supplied by four different delicatessen factories located in Northern Italy. Raw meat underwent experimental contamination with Salmonella spp. using a mixture of 3 strains. Surface contamination of the fresh anatomical cuts was carried out by immersion into inoculum containing Salmonella spp. The conditions of the HPP treatment were: pressure 593 MPa, time 290 seconds, water treatment temperature 14°C. Surface and deep samples were performed post contamination (T0), end of the cold phase (T1), end of process (Tend), and after HPP treatment (postHPP) and Salmonella spp. Enumerated. The results of this study show a significant reduction of Salmonella spp. all through the production process (P<0.01) for all companies, followed by an additional reduction of bacterial counts due to HPP treatment (P<0.01), both in superficial and deep contaminations (P<0.01). The superficial overall reduction resulted of 1.58 to 5.04 log CFU/g during the production process. HPP treatment resulted in a significant (P<0.01) superficial and deep decrease in Salmonella spp. enumeration varying from 0.61 to 4.01 log and from 1.49 to 4.13 log. According to the data presented in this study, only the combined approach of coppa manufacturing process followed by HPP treatment always led to a 5-log reduction of Salmonella spp. required by USDA/FSIS guidelines.
RESUMEN
In this study the effect of the application of High Pressure Treatment (HPP) combined with four different manufacturing processes on the inactivation of Listeria innocua, used as a surrogate for L. monocytogenes, in artificially contaminated coppa samples was evaluated in order to verify the most suitable strategy to meet the Listeria inactivation requirements needed for the exportation of dry-cured meat in the U.S. Fresh anatomical cuts intended for coppa production were supplied by four different delicatessen factories located in Northern Italy. Raw meat underwent experimental contamination with Listeria innocua using a mixture of 5 strains. Surface contamination of the fresh anatomical cuts was carried out by immersion into inoculum containing Listeria spp. The conditions of the HPP treatment were: pressure 593 MPa, time 290 seconds, water treatment temperature 14°C. Listeria innocua was enumerated on surface and deep samples post contamination, resting, ripening and HPP treatment. The results of this study show how the reduction of the microbial load on coppa during the production process did not vary among three companies (P>0.05) ranging from 3.73 to 4.30 log CFU/g, while it was significantly different (P<0.01) for the fourth company (0.92 log CFU/g). HPP treatment resulted in a significant (P<0.01) deep decrease of L. innocua count with values ranging between 1.63-3.54 log CFU/g with no significant differences between companies. Regarding superficial contamination, HPP treatment resulted significant (P<0.01) only in Coppa produced by two companies. The results highlight that there were processes less effective to inhibit the pathogen; in particular for company D an increase of L. innocua count was shown during processing and HPP alone cannot be able to in reaching the Listeria inactivation requirements needed for exportation of dry-cured meat in the U.S. According to the data reported in this paper, HPP treatment increases the ability of the manufacturing process of coppa in reducing Listeria count with the objective of a lethality treatment.
RESUMEN
During the years 2015-2016, 83 faecal samples were collected at slaughter from pigs reared in farms located in Central-Northern Italy. During the years 2014-2016 a total of 562 pork products [465 not-readyto-eat (NRTE) and 97 ready-to-eat (RTE) products] were collected from retail outlets, large retailers and processing plants. The samples were analysed according to ISO TS 13136:2012. Out of 83 swine faecal samples, 77 (92.8%) resulted stx-positive by real time polymerase chain reaction (PCR), 5 stx2+ and 1 stx1+ Shiga toxin-producing Escherichia coli (STEC) strains were isolated. Among the 465 NRTE samples, 65 (14.0%) resulted stx-positive by real time PCR and 7 stx2+ STEC strains were isolated. The stx2 gene was detected more frequently than the stx1 gene both in faecal samples (90.4 vs 8.4%) and in NRTE pork products (13.3 vs 1.3%). All the RTE samples included in the analysis resulted stx-negative. Among the samples resulted positive for stx and eae genes, serogroup-associated genes were detected at high frequency: O26 resulted the most frequent in faecal samples (81.3%) and O145 in pork products (88.1%). The O157 serogroup resulted positive in 83.3 and 78.1% of pork products and faecal samples, respectively. Despite the frequent detection by real time PCR of genes indicating the possible presence of STEC strains belonging to the six serogroups, the bacteriological step did not confirm the isolation of any such strains.
