Probing the Ni(OH)2 Precursor for LiNiO2 at the Atomic Scale: Insights into the Origin of Structural Defect in a Layered Cathode Active Material.

In lithium ion batteries (LIBs), the layered cathode materials of composition LiNi1- x - y Cox Mny O2  are critical for achieving high energy densities. A high nickel content (>80%) provides an attractive balance between high energy density, long lifetime, and low cost. Consequently, Ni-rich layered oxides cathode active materials (CAMs) are in high demand, and the importance of LiNiO2 (LNO) as limiting case, is hence paramount. However, achieving perfect stoichiometry is a challenge resulting in various structural issues, which successively impact physicochemical properties and result in the capacity fade of LIBs. To better understand defect formation in LNO, the role of the Ni(OH)2  precursor morphology in the synthesis of LNO requires in-depth investigation. By employing aberration-corrected scanning transmission electron microscopy, electron energy loss spectroscopy, and precession electron diffraction, a direct observation of defects in the Ni(OH)2  precursor preparedis reported and the ex situ structural evolution from the precursor to the end product is monitored. During synthesis, the layered Ni(OH)2  structure transforms to partially lithiated (non-layered) NiO and finally to layered LNO. The results suggest that the defects observed in commercially relevant CAMs originate to a large extent from the precursors, hence care must be taken in tuning the co-precipitation parameters to synthesize defect-free Ni-rich layered oxides CAMs.

Zn Redistribution and Volatility in ZnZrOx Catalysts for CO2 Hydrogenation.

ZnO-ZrO2 mixed oxide (ZnZrOx) catalysts are widely studied as selective catalysts for CO2 hydrogenation into methanol at high-temperature conditions (300-350 °C) that are preferred for the subsequent in situ zeolite-catalyzed conversion of methanol into hydrocarbons in a tandem process. Zn, a key ingredient of these mixed oxide catalysts, is known to volatilize from ZnO under high-temperature conditions, but little is known about Zn mobility and volatility in mixed oxides. Here, an array of ex situ and in situ characterization techniques (scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDX), transmission electron microscopy (TEM), powder X-ray diffraction (PXRD), X-ray absorption spectroscopy (XAS), X-ray photoelectron spectroscopy (XPS), Infrared (IR)) was used to reveal that Zn2+ species are mobile between the solid solution phase with ZrO2 and segregated and/or embedded ZnO clusters. Upon reductive heat treatments, partially reversible ZnO cluster growth was observed above 250 °C and eventual Zn evaporation above 550 °C. Extensive Zn evaporation leads to catalyst deactivation and methanol selectivity decline in CO2 hydrogenation. These findings extend the fundamental knowledge of Zn-containing mixed oxide catalysts and are highly relevant for the CO2-to-hydrocarbon process optimization.

Operando Laboratory-Based Multi-Edge X-Ray Absorption Near-Edge Spectroscopy of Solid Catalysts.

Laboratory-based X-ray absorption spectroscopy (XAS) and especially X-ray absorption near-edge structure (XANES) offers new opportunities in catalyst characterization and presents not only an alternative, but also a complementary approach to precious beamtime at synchrotron facilities. We successfully designed a laboratory-based setup for performing operando, quasi-simultaneous XANES analysis at multiple K-edges, more specifically, operando XANES of mono-, bi-, and trimetallic CO2 hydrogenation catalysts containing Ni, Fe, and Cu. Detailed operando XANES studies of the multielement solid catalysts revealed metal-dependent differences in the reducibility and re-oxidation behavior and their influence on the catalytic performance in CO2 hydrogenation. The applicability of operando laboratory-based XANES at multiple K-edges paves the way for advanced multielement catalyst characterization complementing detailed studies at synchrotron facilities.

Reaction of Li1.3Al0.3Ti1.7(PO4)3 and LiNi0.6Co0.2Mn0.2O2 in Co-Sintered Composite Cathodes for Solid-State Batteries.

All solid-state batteries offer the possibility of increased safety at potentially higher energy densities compared to conventional lithium-ion batteries. In an all-ceramic oxide battery, the composite cathode consists of at least one ion-conducting solid electrolyte and an active material, which are typically densified by sintering. In this study, the reaction of the solid electrolyte Li1.3Al0.3Ti1.7(PO4)3 (LATP) and the active material LiNi0.6Co0.2Mn0.2O2 (NCM622) is investigated by cosintering at temperatures between 550 and 650 °C. The characterization of the composites and the reaction layer is performed by optical dilatometry, X-ray diffractometry, field emission scanning electron microscopy with energy dispersive X-ray spectroscopy, time-of-flight secondary ion mass spectrometry, as well as scanning transmission electron microscopy (STEM). Even at low sintering temperatures, elemental diffusion occurs between the two phases, which leads to the formation of secondary phases and decomposition reactions of the active material and the solid electrolyte. As a result, the densification of the composite is prevented and ion-conducting paths between individual particles cannot be formed. Based on the experimental results, a mechanism of the reactions in cosintered LATP and NCM622 oxide composite cathodes is suggested.

In Situ Monitoring of Thermally Induced Effects in Nickel-Rich Layered Oxide Cathode Materials at the Atomic Level.

The thermal stability of cathode active materials (CAMs) is of major importance for the safety of lithium-ion batteries (LIBs). A thorough understanding of how commercially viable layered oxide CAMs behave at the atomic length scale upon heating is indispensable for the further development of LIBs. Here, structural changes of Li(Ni0.85Co0.15Mn0.05)O2 (NCM851005) at elevated temperatures are studied by in situ aberration-corrected scanning transmission electron microscopy (AC-STEM). Heating NCM851005 inside the microscope under vacuum conditions enables us to observe phase transitions and other structural changes at high spatial resolutions. This has been primarily possible by establishing low-dose electron beam conditions in STEM. Specific focus is put on the evolution of inherent nanopore defects found in the primary grains, which are believed to play an important role in LIB degradation. The onset temperature of structural changes is found to be ∼175 °C, resulting in phase transformation from a layered to a rock-salt-like structure, especially at the internal interfaces, and increasing intragrain inhomogeneity. The reducing environment and heat application lead to the formation and subsequent densification of {003}- and {014}-type facets. In the light of these results, postsynthesis electrode drying processes applied under reducing environment and heat, for example, in the preparation of solid-state batteries, should be re-examined carefully.

The Role of Intragranular Nanopores in Capacity Fade of Nickel-Rich Layered Li(Ni1-x-yCoxMny)O2 Cathode Materials.

Ni-rich layered LiNi1-x-yCoxMnyO2 (NCM, x + y ≤ 0.2) is an intensively studied class of cathode active materials for lithium-ion batteries, offering the advantage of high specific capacities. However, their reactivity is also one of the major issues limiting the lifetime of the batteries. NCM degradation, in literature, is mostly explained both by disintegration of secondary particles (large anisotropic volume changes during lithiation/delithiation) and by formation of rock-salt like phases at the grain surfaces at high potential with related oxygen loss. Here, we report the presence of intragranular nanopores in Li1+x(Ni0.85Co0.1Mn0.05)1-xO2 (NCM851005) and track their morphological evolution from pristine to cycled material (200 and 500 cycles) using aberration-corrected scanning transmission electron microscopy (STEM), electron energy loss spectroscopy, energy dispersive X-ray spectroscopy, and time-of-flight secondary ion mass spectrometry. Pores are already found in the primary particles of pristine material. Any potential effect of TEM sample preparation on the formation of nanopores is ruled out by performing thickness series measurements on the lamellae produced by focused ion beam milling. The presence of nanopores in pristine NCM851005 is in sharp contrast to previously observed pore formation during electrochemical cycling or heating. The intragranular pores have a diameter in the range between 10 and 50 nm with a distinct morphology that changes during cycling operation. A rock-salt like region is observed at the pore boundaries even in pristine material, and these regions grow with prolonged cycling. It is suggested that the presence of nanopores strongly affects the degradation of high-Ni NCM, as the pore surfaces apparently increase (i) oxygen loss, (ii) formation of rock-salt regions, and (iii) strain-induced effects within the primary grains. High-resolution STEM demonstrates that nanopores are a source of intragranular cracking during cycling.

Synthesis of centimeter-size free-standing perovskite nanosheets from single-crystal lead bromide for optoelectronic devices.

Considerable attention has been drawn to the lead halide perovskites (LHPs) because of their outstanding optoelectronic characteristics. LHP nanosheets (NSs) grown from single crystalline lead halide possess advantages in device applications as they provide the possibility for control over morphology, composition, and crystallinity. Here, free-standing lead bromide (PbBr2) single-crystalline NSs with sizes up to one centimeter are synthesized from solution. These NSs can be converted to LHP while maintaining the NS morphology. We demonstrate that these perovskite NSs can be processed directly for fabrication of photodetector and laser arrays on a large scale. This strategy will allow high-yield synthesis of large-size perovskite NSs for functional devices in an integrated photonics platform.

Lithium Titanate/Carbon Nanotubes Composites Processed by Ultrasound Irradiation as Anodes for Lithium Ion Batteries.

In this work, lithium titanate nanoparticles (nLTO)/single wall carbon nanotubes (SWCNT) composite electrodes are prepared by the combination of an ultrasound irradiation and ultrasonic spray deposition methods. It was found that a mass fraction of 15% carbon nanotubes optimizes the electrochemical performance of nLTO electrodes. These present capacities as high as 173, 130, 110 and 70 mAh.g-1 at 0.1C, 1C, 10C and 100C, respectively. Moreover, after 1000 cycles at 1C, the nLTO/SWCNT composites present a capacity loss of just 9% and a Coulombic efficiency of 99.8%. Therefore, the presented methodology might be extended to other suitable active materials in order to manufacture binder free electrodes with optimal energy storage capabilities.

Liquid exfoliation of solvent-stabilized few-layer black phosphorus for applications beyond electronics.

Few-layer black phosphorus (BP) is a new two-dimensional material which is of great interest for applications, mainly in electronics. However, its lack of environmental stability severely limits its synthesis and processing. Here we demonstrate that high-quality, few-layer BP nanosheets, with controllable size and observable photoluminescence, can be produced in large quantities by liquid phase exfoliation under ambient conditions in solvents such as N-cyclohexyl-2-pyrrolidone (CHP). Nanosheets are surprisingly stable in CHP, probably due to the solvation shell protecting the nanosheets from reacting with water or oxygen. Experiments, supported by simulations, show reactions to occur only at the nanosheet edge, with the rate and extent of the reaction dependent on the water/oxygen content. We demonstrate that liquid-exfoliated BP nanosheets are potentially useful in a range of applications from ultrafast saturable absorbers to gas sensors to fillers for composite reinforcement.