RESUMEN
High temperature, high energy density, and low loss dielectric films are promising candidates for miniaturized capacitors in electric vehicles and high-speed trains. However, single-component polymers could not achieve these desired properties simultaneously. Polymer multilayer films (MLFs), which combine a high dielectric constant polymer [e.g., poly(vinylidene fluoride) (PVDF)] and a high breakdown/low loss polymer [e.g., polycarbonate (PC)] in a unique layered structure, have the potential achieve them at the same time. In this work, the effects of PC glass transition temperature (Tg) on the dielectric insulation properties (breakdown strength and lifetime) were investigated at high temperatures of 100-150 °C. Three PC materials had Tg values of 145 (PC1), 165 (PC2), and 185 °C (PC3), respectively. It is observed that MLF-PC3 with the highest Tg of PC exhibited the highest Weibull direct/alternating current (DC/AC) breakdown strength and the longest DC/AC lifetime, whereas MLF-PC1 with the lowest Tg showed the lowest Weibull DC/AC breakdown strength and the shortest DC/AC lifetime. A high-temperature high-volage leakage current study revealed that MLF-PC3 exhibited the lowest bulk conductivity at all temperatures under different electric fields. The knowledge obtained from this study will help us design better MLFs with high performance for next-generation miniaturized capacitors.
RESUMEN
To meet the stringent requirements of next-generation film capacitors for power electronics, multilayer films (MLFs) are fabricated with the advantage of achieving high temperature rating, high energy density, and reasonably low loss simultaneously. In this study, a high permittivity polar polymer, poly(vinylidene fluoride) (PVDF), is multilayered with a linear, low loss dielectric polymer such as high-temperature polycarbonate (HTPC). However, the dielectric loss of these MLFs was still high as compared with current state-of-the-art biaxially oriented polypropylene (BOPP) films. The goal of this work is to decrease the dielectric loss and enhance dielectric insulation by achieving flat-on primary PVDF crystals in MLFs via nanoconfined melt-recrystallization. Based on simultaneous small- and wide-angle X-ray scattering experiments, edge-on lamellar crystals were observed for all as-extruded MLFs, regardless of different PVDF layer thicknesses. However, after melting at 180 °C followed by recrystallization, flat-on primary crystals were successfully achieved when the PVDF layer thickness was below 39 nm. Above 78 nm for the PVDF layer, major edge-on primary crystals with minor flat-on secondary crystals were observed. From leakage current, breakdown, lifetime, and electric displacement-electric field loop studies, MLFs with the flat-on primary crystals exhibited reduced loss and enhanced dielectric insulation as compared to as-extruded MLFs and those with edge-on primary/flat-on secondary crystals. This was attributed to the effective blockage of charge carriers by the flat-on PVDF primary crystals and their reduced ferroelectric switching.
RESUMEN
In this paper, we develop the methodology, including the refraction correction, geometrical thickness correction, coordinate transformation, and layer segmentation algorithms, for 3D rendering and metrology of a layered spherical gradient refractive index (S-GRIN) lens based on the imaging data collected by an angular scan optical coherence tomography (OCT) system. The 3D mapping and rendering enables direct 3D visualization and internal defect inspection of the lens. The metrology provides assessment of the surface geometry, the lens thickness, the radii of curvature of the internal layer interfaces, and the misalignment of the internal S-GRIN distribution with respect to the lens surface. The OCT metrology results identify the manufacturing defects, and enable targeted process development for optimizing the manufacturing parameters. The newly fabricated S-GRIN lenses show up to a 7x spherical aberration reduction that allows a significantly increased utilizable effective aperture.
RESUMEN
A hybrid confocal-scan swept-source optical coherence tomography metrology system was conceived for simultaneous measurements of the refractive index and thickness profiles of polymeric layered gradient refractive index (GRIN) optics. An uncertainty analysis predicts the metrology capability of the system and guides the selection of an optimum working numerical aperture. Experimental results on both a monolithic and a GRIN layered sheet are demonstrated to be in close agreement with theoretical predictions. Index measurement precision reached 0.0001 and 0.0008 for measuring 2.8 mm and ~300 µm thick layers, respectively. The thicknesses of these layers were simultaneously measured with a precision of 0.28 and 0.17 µm, respectively.
RESUMEN
The fabrication of high-performance spherical gradient refractive index (S-GRIN) optics requires nondestructive metrology techniques to inspect the samples. We have developed an angular-scan, swept-source-based, Fourier-domain optical coherence tomography (OCT) system centered at 1318 nm with 5 mm imaging depth capable of 180° polar scan and 360° azimuthal scan to investigate polymeric S-GRIN preforms. We demonstrate a method that enables simultaneous mapping of the group optical thickness, physical thickness, the radially-averaged group refractive index, and the transmitted wavefront of the S-GRIN preforms. The angular scan OCT imaging and metrology enables direct visualization, molding uniformity characterization, and optical property evaluations of the preforms. The results on two generations of S-GRIN preforms are discussed that showcase the evolution of the manufacturing process in response to the OCT metrology feedback.
RESUMEN
A synthetic polymeric lens was designed and fabricated based on a bio-inspired, "Age=5" human eye lens design by utilizing a nanolayered polymer film-based technique. The internal refractive index distribution of an anterior and posterior GRIN lens were characterized and confirmed against design by µATR-FTIR. 3D surface topography of the fabricated aspheric anterior and posterior lenses was measured by placido-cone topography and exhibited confirmation of the desired aspheric surface shape. Furthermore, the wavefronts of aspheric posterior GRIN and PMMA lenses were measured and simulated by interferometry and Zemax software, respectively. Their results show that the gradient index distribution reduces the overall wavefront error as compared a homogenous PMMA lens of an identical geometry. Finally, the anterior and posterior GRIN lenses were assembled into a bio-inspired GRIN human eye lens through which a clear imaging was possible.
