Ordered mesoporous carbon (OMC) scaffolds were covalently modified with primary amine groups by means of oxidation-coupling, yielding C-O-C bonds, or organometallic activation-coupling, yielding C-C bonds. The aminated OMCs were stressed by immersion in either 1 M hydrochloric acid or 1 M sodium hydroxide solutions at room temperature for 6 h and characterized by nitrogen sorption, electron microscopy, low-angle X-ray diffraction, thermogravimetric analysis, and the 4-nitrobenzaldehyde assay. Results demonstrate that aminated surfaces of OMC by butyllithium grafting are stable toward both 1 M HCl and 1 M NaOH, whereas the oxidation-aminated OMC surfaces can withstand 1 M NaOH only. This study illustrates the importance of chemical testing to supplant chemical intuition when tailoring carbon surfaces for applications where strong acids or bases are employed. This is especially emphasized for carbonaceous materials because of the surface heterogeneity among different carbon allotropes.
X-ray photoelectron spectroscopy (XPS) is one of the most common techniques used to analyze the surface composition of catalysts and support materials used in polymer electrolyte membrane (PEM) fuel cells and electrolyzers, providing important insights for further improvement of their properties. Characterization of catalyst layers (CLs) is more challenging, which can be at least partially attributed to the instability of ionomer materials such as Nafion during measurements. This work explores the stability of Nafion during XPS measurements, illuminating and addressing Nafion degradation concerns. The extent of Nafion damage as a function of XPS instrumentation, measurement conditions, and sample properties was evaluated across multiple instruments. Results revealed that significant Nafion damage to the ion-conducting sulfonic acid species (>50% loss in sulfur signal) may occur in a relatively short time frame (tens of minutes) depending on the exact nature of the sample and XPS instrument. This motivated the development and validation of a multipoint XPS data acquisition protocol that minimizes Nafion damage, resulting in reliable data acquisition by avoiding significant artifacts from Nafion instability. The developed protocol was then used to analyze both thin film ionomer samples and Pt/C-based CLs. Comparison of PEM fuel cell CLs to Nafion thin films revealed several changes in Nafion spectral features attributed to charge transfer due to interaction with conductive catalyst and support species. This study provides a method to reliably characterize ionomer-containing samples, facilitating fundamental studies of the catalyst-ionomer interface and more applied investigations of structure-processing-performance correlations in PEM fuel cell and electrolyzer CLs.
Materials that are capable of adsorbing and desorbing gases near ambient conditions are highly sought after for many applications in gas storage and separations. While the physisorption of typical gases to high surface area covalent organic frameworks (COFs) occurs through relatively weak intermolecular forces, the tunability of framework materials makes them promising candidates for tailoring gas sorption enthalpies. The incorporation of open Cu(I) sites into framework materials is a proven strategy to increase gas uptake closer to ambient conditions for gases that are capable of π-back-bonding with Cu. Here, we report the synthesis of a Cu(I)-loaded COF with subnanometer pores and a three-dimensional network morphology, namely Cu(I)-COF-301. This study focused on the sorption mechanisms of hydrogen, ethylene, and carbon monoxide with this material under ultrahigh vacuum using temperature-programmed desorption and Kissinger analyses of variable ramp rate measurements. All three gases desorb near or above room temperature under these conditions, with activation energies of desorption (E des) calculated as approximately 29, 57, and 68 kJ/mol, for hydrogen, ethylene, and carbon monoxide, respectively. Despite these strong Cu(I)-gas interactions, this work demonstrated the ability to desorb each gas on-demand below its normal desorption temperature upon irradiation with ultraviolet (UV) light. While thermal imaging experiments indicate that bulk photothermal heating of the COF accounts for some of the photodriven desorption, density functional theory calculations reveal that binding enthalpies are systematically lowered in the COF-hydrogen matrix excited state initiated by UV irradiation, further contributing to gas desorption. This work represents a step toward the development of more practical ambient temperature storage and efficient regeneration of sorbents for applications with hydrogen and π-accepting gases through the use of external photostimuli.
This study explored the fundamental chemical intricacies behind the interactions between metal catalysts and carbon supports with graphitic nitrogen defects. These interactions were probed by examining metal adsorption, specifically, the location of adsorption and the electronic structure of metal catalysts as the basis for the metal-support interactions (MSIs). A computational framework was developed, and a series of 12 transition metals was systematically studied over various graphene models with graphitic nitrogen defect(s). Different modeling approaches served to provide insights into previous MSI computational discrepancies, reviewing both truncated and periodic graphene models. The computational treatment affected the magnitudes of adsorption energies between the metals and support; however, metals generally followed the same trends in their MSI. It was found that the addition of the nitrogen dopant improved the MSI by promoting electronic rearrangement from the metals' d- to s-orbitals for greater orbital overlap with the carbon support, shown with increased favorable adsorption. Furthermore, the study observed periodic trends that were adept descriptors of the MSI fundamental chemistries.
Platinum-nickel (Pt-Ni) nanowires were developed as hydrogen evolving catalysts for anion exchange membrane electrolyzers. Following synthesis by galvanic displacement, the nanowires had Pt surface areas of 90 m2 gPt-1. The nanowire specific exchange current densities were 2-3 times greater than commercial nanoparticles and may benefit from the extended nanostructure morphology that avoids fringe facets and produces higher quantities of Pt{100}. Hydrogen annealing was used to alloy Pt and Ni zones and compress the Pt lattice. Following annealing, the nanowire activity improved to 4 times greater than the as-synthesized wires and 10 times greater than Pt nanoparticles. Density functional theory calculations were performed to investigate the influence of lattice compression and exposed facet on the water-splitting reaction; it was found that at a lattice of 3.77 Å, the (100) facet of a Pt-skin grown on Ni3Pt weakens hydrogen binding and lowers the barrier to water-splitting as compared to pure Pt(100). Moreover, the activation energy of water-splitting on the (100) facet of a Pt-skin grown on Ni3Pt is particularly advantageous at 0.66 eV as compared to the considerably higher 0.90 eV required on (111) surfaces of pure Pt or Pt-skin grown on Ni3Pt. This favorable effect may be slightly mitigated during further optimization procedures such as acid leaching near-surface Ni, necessary to incorporate the nanowires into electrolyzer membrane electrode assemblies. Exposure to acid resulted in slight dealloying and Pt lattice expansion, which reduced half-cell activity, but exposed Pt surfaces and improved single-cell performance. Membrane electrode assembly performance was kinetically 1-2 orders of magnitude greater than Ni and slightly better than Pt nanoparticles while at one tenth the Pt loading. These electrocatalysts potentially exploit the highly active {100} facets and provide an ultralow Pt group metal option that can enable anion exchange membrane electrolysis, bridging the gap to proton exchange membrane-based systems.
In situ electrochemical diagnostics designed to probe ionomer interactions with platinum and carbon were applied to relate ionomer coverage and conformation, gleaned from anion adsorption data, with O2 transport resistance for low-loaded (0.05 mgPt cm-2) platinum-supported Vulcan carbon (Pt/Vu)-based electrodes in a polymer electrolyte fuel cell. Coupling the in situ diagnostic data with ex situ characterization of catalyst inks and electrode structures, the effect of ink composition is explained by both ink-level interactions that dictate the electrode microstructure during fabrication and the resulting local ionomer distribution near catalyst sites. Electrochemical techniques (CO displacement and ac impedance) show that catalyst inks with higher water content increase ionomer (sulfonate) interactions with Pt sites without significantly affecting ionomer coverage on the carbon support. Surprisingly, the higher anion adsorption is shown to have a minor impact on specific activity, while exhibiting a complex relationship with oxygen transport. Ex situ characterization of ionomer suspensions and catalyst/ionomer inks indicates that the lower ionomer coverage can be correlated with the formation of large ionomer aggregates and weaker ionomer/catalyst interactions in low-water content inks. These larger ionomer aggregates resulted in increased local oxygen transport resistance, namely, through the ionomer film, and reduced performance at high current density. In the water-rich inks, the ionomer aggregate size decreases, while stronger ionomer/Pt interactions are observed. The reduced ionomer aggregation improves transport resistance through the ionomer film, while the increased adsorption leads to the emergence of resistance at the ionomer/Pt interface. Overall, the high current density performance is shown to be a nonmonotonic function of ink water content, scaling with the local gas (H2, O2) transport resistance resulting from pore, thin film, and interfacial phenomena.
We present an investigation of the structure and rheological behavior of catalyst inks for low-temperature polymer electrolyte membrane water electrolyzers. The ink consists of iridium oxide (IrO2) catalyst particles and a Nafion ionomer dispersed in a mixture of 1-propanol and water. The effects of ionomer concentration and catalyst concentration on the microstructure of the catalyst ink were studied. Studies on dilute inks (0.1 wt % IrO2) using zeta potential and dynamic light scattering measurements indicated a strong adsorption of the ionomer onto the catalyst particles which resulted in an increase in the ζ-potential and the z-average diameter. Steady-shear and dynamic-oscillatory-shear rheological measurements of concentrated IrO2 dispersions (35 wt % IrO2) indicated that the particles are strongly agglomerated in the absence of the ionomer. The addition of even a small amount of the ionomer (2.4 wt % with respect to total solids) caused the rheology to transition from shear thinning to Newtonian because of the reduction in agglomerated structure due to stabilization of the aggregates by the ionomer, consistent with the behavior of dilute inks. At intermediate ionomer loadings, between 2.4 and 9 wt %, the viscosity increased with increasing ionomer wt %, though remained Newtonian, predominantly due to the increasing ionomer volume fraction in the ink. For ionomer loadings greater than 9 wt %, the particles were found to be flocculated, likely induced by a dispersed ionomer. The flocculated inks exhibited strong shear-thinning and gel-like behaviors in steady-shear and oscillatory-shear rheology. The onset of flocculation was found to be sensitive to the catalyst concentration, where below 35 wt % of IrO2, flocculation was not observed. The rheological observations were further verified by ultra-small-angle X-ray scattering.
Silicon (Si) is a commonly studied candidate material for next-generation anodes in Li-ion batteries. A native oxide SiO2 on Si is often inevitable. However, it is not clear if this layer has a positive or negative effect on the battery performance. This understanding is complicated by the lack of knowledge about the physical properties of the SiO2 lithiation products and by the convolution of chemical and electrochemical effects during the anode lithiation process. In this study, Li xSiO y thin films as model materials for lithiated SiO2 were deposited by magnetron sputtering at ambient temperature, with the goal of (1) decoupling chemical reactivity from electrochemical reactivity and (2) evaluating the physical and electrochemical properties of Li xSiO y. X-ray photoemission spectroscopy analysis of the deposited thin films demonstrate that a composition close to previous experimental reports of lithiated native SiO2 can be achieved through sputtering. Our density functional theory calculations also confirm that the possible phases formed by lithiating SiO2 are very close to the measured film compositions. Scanning probe microscopy measurements show that the mechanical properties of the film are strongly dependent on lithium concentration, with a ductile behavior at a higher Li content and a brittle behavior at a lower Li content. The chemical reactivity of the thin films was investigated by measuring the AC impedance evolution, suggesting that Li xSiO y continuously reacts with the electrolyte, in part because of the high electronic conductivity of the film determined from solid-state impedance measurements. The electrochemical cycling data of the sputter-deposited Li xSiO y/Si films also suggest that Li xSiO y is not beneficial in stabilizing the Si anode surface during battery operation, despite its favorable mechanical properties.
Silicon (Si) is a commonly studied candidate material for next-generation anodes in Li-ion batteries. A native oxide SiO2 on Si is often inevitable. However, it is not clear if this layer has positive or negative effect on the battery performance. This understanding is complicated by the lack of knowledge about the physical properties, and by convolution of chemical and electrochemical effects during the anode lithiation process. In this study, LixSiOy thin films as model materials for lithiated SiO2 were deposited by magnetron sputtering at ambient temperature, with the goal of 1) decoupling chemical reactivity from electrochemical reactivity, and 2) evaluating the physical and electrochemical properties of LixSiOy. XPS analysis of the deposited thin films demonstrate that a composition close to previous experimental reports of lithiated native SiO2, can be achieved through sputtering. Our density functional theory calculations also confirm that possible phases formed by lithiating SiO2 are very close to the measured film compositions. Scanning probe microscopy measurements show the mechanical properties of the film are strongly dependent on lithium concentration, with ductile behavior and higher Li content and brittle behavior at lower Li content. Chemical reactivity of the thin films was investigated by measuring AC impedance evolution, suggesting that LixSiOy continuously reacts with electrolyte, in part due to high electronic conductivity of the film determined from solid state impedance measurements. Electrochemical cycling data of sputter deposited LixSiOy/Si films also suggest that LixSiOy is not beneficial in stabilizing the Si anode surface during battery operation, despite its favorable mechanical properties.
Nanostructured noble-metal catalysts traditionally suffer from sintering under high operating temperatures, leading to durability issues and process limitations. The encapsulation of nanostructured catalysts to prevent loss of activity through thermal sintering, while maintaining accessibility of active sites, remains a great challenge in the catalysis community. Here, we report a robust and regenerable palladium-based catalyst, wherein palladium particles are intercalated into the three-dimensional framework of SBA-15-type mesoporous silica. The encapsulated Pd active sites remain catalytically active as demonstrated in high-temperature/pressure phenol hydrodeoxygenation reactions. The confinement of Pd particles in the walls of SBA-15 prevents particle sintering at high temperatures. Moreover, a partially deactivated catalyst containing intercalated particles is regenerated almost completely even after several reaction cycles. In contrast, Pd particles, which are not encapsulated within the SBA-15 framework, sinter and do not recover prior activity after a regeneration procedure.
A precious metal-free cathode catalyst, mesoporous Ba0.5Sr0.5Co0.8Fe0.2O3-δ (m-BSCF), with a well crystallized perovskite framework and a porous structure (pore size of â¼10 nm) has been synthesized by a one-step co-nanocasting method. The obtained mesoporous perovskite m-BSCF demonstrated a much higher oxygen reduction reaction catalytic activity than its macroporous (CS-BSCF of â¼5 µm pore size) and nonporous counterparts (SG-BSCF). The mesoporous structure and oxygen vacancies endowed the obtained perovskite oxide m-BSCF with an approximate 4e- pathway for the ORR comparable to the benchmark 20 wt% Pt/C and a stable electro-catalytic activity with 91% current density being retained after 5000 cycles, and excellent methanol tolerance. The redox couples Co4+/Co3+ and Fe3+/Fe2+ are proposed to accelerate the ORR on active species, i.e., MOOH (M = Co, Fe) groups produced by the substitution species of Co and Fe in the B-site of perovskite m-BSCF, and in the meantime oxygen vacancies generated by the redox couples play a key role in activating the oxygen molecules.
The development of high-performance silicon anodes for the next generation of lithium ion batteries (LIBs) evokes increasing interest in studying its lithiated counterpart-lithium silicide (LixSi). In this paper we report a systematic study of three thermodynamically stable phases of LixSi (x = 4.4, 3.75, and 2.33) plus nitride-protected Li4.4Si, which are synthesized via the high-energy ball-milling technique. All three LixSi phases show improved performance over that of unmodified Si, where Li4.4Si demonstrates optimum performance with a discharging capacity of 3306 (mA h)/g initially and maintains above 2100 (mA h)/g for over 30 cycles and above 1200 (mA h)/g for over 60 cycles at the current density of 358 mA/g of Si. A fundamental question studied is whether different electrochemical paradigms, that is, delithiation first or lithiation first, influence the electrode performance. No significant difference in electrode performance is observed. When a nitride layer (LixNySiz) is created on the surface of Li4.4Si, the cyclability is improved to retain the capacity above 1200 (mA h)/g for more than 80 cycles. By increasing the nitridation extent, the capacity retention is improved significantly from the average decrease of 1.06% per cycle to 0.15% per cycle, while the initial discharge capacity decreases due to the inactivity of Si in the LixNySiz layer. Moreover, the Coulombic efficiencies of all LixSi-based electrodes in the first cycle are significantly higher than that of a Si electrode (â¼90% vs 40-70%).
It can be difficult to simultaneously control the size, composition, and morphology of metal nanomaterials under benign aqueous conditions. For this, bioinspired approaches have become increasingly popular due to their ability to stabilize a wide array of metal catalysts under ambient conditions. In this regard, we used the R5 peptide as a three-dimensional template for formation of PdPt bimetallic nanomaterials. Monometallic Pd and Pt nanomaterials have been shown to be highly reactive toward a variety of catalytic processes, but by forming bimetallic species, increased catalytic activity may be realized. The optimal metal-to-metal ratio was determined by varying the Pd:Pt ratio to obtain the largest increase in catalytic activity. To better understand the morphology and the local atomic structure of the materials, the bimetallic PdPt nanomaterials were extensively studied by transmission electron microscopy, extended X-ray absorption fine structure spectroscopy, X-ray photoelectron spectroscopy, and pair distribution function analysis. The resulting PdPt materials were determined to form multicomponent nanostructures where the Pt component demonstrated varying degrees of oxidation based upon the Pd:Pt ratio. To test the catalytic reactivity of the materials, olefin hydrogenation was conducted, which indicated a slight catalytic enhancement for the multicomponent materials. These results suggest a strong correlation between the metal ratio and the stabilizing biotemplate in controlling the final materials morphology, composition, and the interactions between the two metal species.
Nanostructures , Oxidation-Reduction , Palladium , Peptides , Platinum
For the first time, extended nanostructured catalysts are demonstrated with both high specific activity (>6000 µA cmPt -2 at 0.9 V) and high surface areas (>90 m2 gPt -1). Platinum-nickel (Pt-Ni) nanowires, synthesized by galvanic displacement, have previously produced surface areas in excess of 90 m2 gPt -1, a significant breakthrough in and of itself for extended surface catalysts. Unfortunately, these materials were limited in terms of their specific activity and durability upon exposure to relevant electrochemical test conditions. Through a series of optimized postsynthesis steps, significant improvements were made to the activity (3-fold increase in specific activity), durability (21% mass activity loss reduced to 3%), and Ni leaching (reduced from 7 to 0.3%) of the Pt-Ni nanowires. These materials show more than a 10-fold improvement in mass activity compared to that of traditional carbon-supported Pt nanoparticle catalysts and offer significant promise as a new class of electrocatalysts in fuel cell applications.
Recent advances in theoretical structure prediction methods and high-throughput computational techniques are revolutionizing experimental discovery of the thermodynamically stable inorganic materials. Metastable materials represent a new frontier for these studies, since even simple binary non-ground state compounds of common elements may be awaiting discovery. However, there are significant research challenges related to non-equilibrium thin film synthesis and crystal structure predictions, such as small strained crystals in the experimental samples and energy minimization based theoretical algorithms. Here, we report on experimental synthesis and characterization, as well as theoretical first-principles calculations of a previously unreported mixed-valent binary tin nitride. Thin film experiments indicate that this novel material is N-deficient SnN with tin in the mixed ii/iv valence state and a small low-symmetry unit cell. Theoretical calculations suggest that the most likely crystal structure has the space group 2 (SG2) related to the distorted delafossite (SG166), which is nearly 0.1 eV/atom above the ground state SnN polymorph. This observation is rationalized by the structural similarity of the SnN distorted delafossite to the chemically related Sn3N4 spinel compound, which provides a fresh scientific insight into the reasons for growth of polymorphs of metastable materials. In addition to reporting on the discovery of the simple binary SnN compound, this paper illustrates a possible way of combining a wide range of advanced characterization techniques with the first-principle property calculation methods, to elucidate the most likely crystal structure of the previously unreported metastable materials.
Nitriles/chemistry , Tin/chemistry , Crystallization , Molecular Structure , Quantum Theory , X-Ray Diffraction
Low-temperature direct methane fuel cells (DMEFCs) offer the opportunity to substantially improve the efficiency of energy production from natural gas. This study focuses on the development of well-defined platinum organometallic complexes covalently anchored to ordered mesoporous carbon (OMC) for electrochemical oxidation of methane in a proton exchange membrane fuel cell at 80 °C. A maximum normalized power of 403 µW/mg Pt was obtained, which was 5 times higher than the power obtained from a modern commercial catalyst and 2 orders of magnitude greater than that from a Pt black catalyst. The observed differences in catalytic activities for oxidation of methane are linked to the chemistry of the tethered catalysts, determined by X-ray photoelectron spectroscopy. The chemistry/activity relationships demonstrate a tangible path for the design of electrocatalytic systems for C-H bond activation that afford superior performance in DMEFC for potential commercial applications.
Carbon/chemistry , Methane/chemistry , Organometallic Compounds/chemistry , Temperature , Catalysis , Microscopy, Electron , Oxidation-Reduction , Photoelectron Spectroscopy
The quantum confinement and enhanced optical properties of silicon quantum dots (SiQDs) make them attractive as an inexpensive and nontoxic material for a variety of applications such as light emitting technologies (lighting, displays, sensors) and photovoltaics. However, experimental demonstration of these properties and practical application into optoelectronic devices have been limited as SiQDs are generally passivated with covalently bound insulating alkyl chains that limit charge transport. In this work, we show that strategically designed triphenylamine-based surface ligands covalently bonded to the SiQD surface using conjugated vinyl connectivity results in a 70 nm red-shifted photoluminescence relative to their decyl-capped control counterparts. This suggests that electron density from the SiQD is delocalized into the surface ligands to effectively create a larger hybrid QD with possible macroscopic charge transport properties.
We have developed a novel single-step technique based on nonthermal, radio frequency (rf) plasmas to synthesize sub-10 nm, core-shell, carbon-coated crystalline Si (c-Si) nanoparticles (NPs) for potential application in Li(+) batteries and as fluorescent markers. Hydrogen-terminated c-Si NPs nucleate and grow in a SiH4-containing, low-temperature plasma in the upstream section of a tubular quartz reactor. The c-Si NPs are then transported downstream by gas flow, and are coated with amorphous carbon (a-C) in a second C2H2-containing plasma. X-ray diffraction (XRD), X-ray photoelectron spectroscopy, and in situ attenuated total reflection Fourier transform infrared spectroscopy show that a thin, < 1 nm, 3C-SiC layer forms at the c-Si/a-C interface. By varying the downstream C2H2 plasma rf power, we can alter the nature of the a-C coating as well as the thickness of the interfacial 3C-SiC layer. The transmission electron microscopy (TEM) analysis is in agreement with the Si NP core size determined by Raman spectroscopy, photoluminescence spectroscopy, and XRD analysis. The size of the c-Si NP core, and the corresponding light emission from these NPs, was directly controlled by varying the thickness of the interfacial 3C-SiC layer. This size tunable emission thus also demonstrates the versatility of this technique for synthesizing c-Si NPs for potential applications in light emitting diodes, biological markers, and nanocrystal inks.
Carbon/chemistry , Nanoparticles/chemistry , Nanotechnology/methods , Silicon/chemistry , Equipment Design , Plasma Gases , Radio Waves , X-Ray Diffraction
A commercial PtRu/C catalyst postdoped with nitrogen demonstrates a significantly higher performance (~10-20% improvement) in the anode of an alkaline direct methanol fuel cell than an unmodified commercial PtRu/C catalyst control. The enhanced performance shown herein is attributed at least partially to the increased electrochemical surface area of the PtRu/C after postdoping with nitrogen.
Electric Power Supplies , Methanol/chemistry , Nitrogen/chemistry , Catalysis , Electrodes , Hydrogen-Ion Concentration
Particles with hierarchical porosity can be formed by templating silica microparticles with a specially designed surfactant micelle/oil nanoemulsion mixture. The nanoemulsion oil droplet and micellar dimensions determine the pore size distribution: one set of pores with diameters of tens of nanometers coexisting with a second subset of pores with diameters of single nanometers. Further practical utility of these nanoporous particles requires precise tailoring of the hierarchical pore structure. In this synthesis study, the particle nanostructure is tuned by adjusting the oil, water, and surfactant mixture composition for the controlled design of nanoemulsion-templated features. We also demonstrate control of the size distribution and surface area of the smaller micelle-templated pores as a consequence of altering the hydrophobic chain length of the molecular surfactant template. Moreover, a microfluidic system is designed to process the low interfacial system for fabrication of monodisperse porous particles. The ability to direct the assembly of template nanoemulsion and micelle structures creates new opportunities to engineer hierarchically porous particles for utility as electrocatalysts for fuel cells, chromatography separations, drug delivery vehicles, and other applications.
Microfluidic Analytical Techniques/methods , Nanoparticles/chemistry , Oxides/chemistry , Emulsions/chemistry , Micelles , Microscopy, Electron, Scanning , Nanoparticles/ultrastructure , Particle Size , Porosity , Silicon Dioxide/chemistry , Sodium Chloride/chemistry , Surface Properties
