Enhanced biomethane production from Scenedesmus sp. using polymer harvesting and expired COVID-19 disinfectant for pretreatment.

This study evaluates the repurposing of expired isopropanol (IPA) COVID-19 disinfectant (64% w/w) to pretreat algal biomass for enhancing methane (CH4) yield. The impact of harvesting methods (centrifugation and polymer flocculation) and microwave pretreatment on CH4 production from Scenedesmus sp. microalgal biomass were also investigated. Results show minimal impact of harvesting methods on the CH4 yield, with wet centrifuged and polymer-harvested biomass exhibiting comparable and low CH4 production at 66 and 74 L/kgvolatile solid, respectively. However, microalgae drying significantly increased CH4 yield compared to wet biomass, attributed to cell shrinkage and enhanced digestibility. Consequently, microwave and IPA pretreatment significantly enhanced CH4 production when applied to dried microalgae, yielding a 135% and 212% increase, respectively, compared to non-pretreated wet biomass. These findings underscore the advantage of using dried Scenedesmus sp. over wet biomass and highlight the synergistic effect of combining oven drying with IPA treatment to boost CH4 production whilst reducing COVID-19 waste.

Mussel-inspired resilient hydrogels with strong skin adhesion and high-sensitivity for wearable device.

Stretchable and self-adhesive conductive hydrogels hold significant importance across a wide spectrum of applications, including human-machine interfaces, wearable devices, and soft robotics. However, integrating multiple properties, such as high stretchability, strong interfacial adhesion, self-healing capability, and sensitivity, into a single material poses significant technical challenges. Herein, we present a multifunctional conductive hydrogel based on poly(acrylic acid) (PAA), dopamine-functionalized pectin (PT-DA), polydopamine-coated reduction graphene oxide (rGO-PDA), and Fe3+ as an ionic cross-linker. This hydrogel exhibits a combination of high stretchability (2000%), rapid self-healing (~ 94% recovery in 5 s), and robust self-adhesion to various substrates. Notably, the hydrogel demonstrates a remarkable skin adhesion strength of 85 kPa, surpassing previous skin adhesive hydrogels. Furthermore, incorporating rGO within the hydrogel network creates electric pathways, ensuring excellent conductivity (0.56 S m-1). Consequently, these conductive hydrogels exhibit strain-sensing properties with a significant increase in gauge factor (GF) of 14.6, covering an extensive detection range of ~ 1000%, fast response (198 ms) and exceptional cycle stability. These multifunctional hydrogels can be seamlessly integrated into motion detection sensors capable of distinguishing between various strong or subtle movements of the human body.

Occurrence, spatiotemporal trends, fate, and treatment technologies for microplastics and organic contaminants in biosolids: A review.

This review provides a comprehensive overview of the occurrence, fate, treatment and multi-criteria analysis of microplastics (MPs) and organic contaminants (OCs) in biosolids. A meta-analysis was complementarily analysed through the literature to map out the occurrence and fate of MPs and 10 different groups of OCs. The data demonstrate that MPs (54.7% occurrence rate) and linear alkylbenzene sulfonate surfactants (44.2% occurrence rate) account for the highest prevalence of contaminants in biosolids. In turn, dioxin, polychlorinated biphenyls (PCBs) and phosphorus flame retardants (PFRs) have the lowest rates (<0.01%). The occurrence of several OCs (e.g., dioxin, per- and polyfluoroalkyl substances, polycyclic aromatic hydrocarbons, pharmaceutical and personal care products, ultraviolet filters, phosphate flame retardants) in Europe appear at higher rates than in Asia and the Americas. However, MP concentrations in biosolids from Australia are reported to be 10 times higher than in America and Europe, which required more measurement data for in-depth analysis. Amongst the OC groups, brominated flame retardants exhibited exceptional sorption to biosolids with partitioning coefficients (log Kd) higher than 4. To remove these contaminants from biosolids, a wide range of technologies have been developed. Our multicriteria analysis shows that anaerobic digestion is the most mature and practical. Thermal treatment is a viable option; however, it still requires additional improvements in infrastructure, legislation, and public acceptance.

Random mutagenesis of Phaeodactylum tricornutum using ultraviolet, chemical, and X-radiation demonstrates the need for temporal analysis of phenotype stability.

We investigated two non-ionising mutagens in the form of ultraviolet radiation (UV) and ethyl methanosulfonate (EMS) and an ionising mutagen (X-ray) as methods to increase fucoxanthin content in the model diatom Phaeodactylum tricornutum. We implemented an ultra-high throughput method using fluorescence-activated cell sorting (FACS) and live culture spectral deconvolution for isolation and screening of potential pigment mutants, and assessed phenotype stability by measuring pigment content over 6 months using high-performance liquid chromatography (HPLC) to investigate the viability of long-term mutants. Both UV and EMS resulted in significantly higher fucoxanthin within the 6 month period after treatment, likely as a result of phenotype instability. A maximum fucoxanthin content of 135 ± 10% wild-type found in the EMS strain, a 35% increase. We found mutants generated using all methods underwent reversion to the wild-type phenotype within a 6 month time period. X-ray treatments produced a consistently unstable phenotype even at the maximum treatment of 1000 Grays, while a UV mutant and an EMS mutant reverted to wild-type after 4 months and 6 months, respectively, despite showing previously higher fucoxanthin than wild-type. This work provides new insights into key areas of microalgal biotechnology, by (i) demonstrating the use of an ionising mutagen (X-ray) on a biotechnologically relevant microalga, and by (ii) introducing temporal analysis of mutants which has substantial implications for strain creation and utility for industrial applications.

Symbiodiniaceae photophysiology and stress resilience is enhanced by microbial associations.

Symbiodiniaceae form associations with extra- and intracellular bacterial symbionts, both in culture and in symbiosis with corals. Bacterial associates can regulate Symbiodiniaceae fitness in terms of growth, calcification and photophysiology. However, the influence of these bacteria on interactive stressors, such as temperature and light, which are known to influence Symbiodiniaceae physiology, remains unclear. Here, we examined the photophysiological response of two Symbiodiniaceae species (Symbiodinium microadriaticum and Breviolum minutum) cultured under acute temperature and light stress with specific bacterial partners from their microbiome (Labrenzia (Roseibium) alexandrii, Marinobacter adhaerens or Muricauda aquimarina). Overall, bacterial presence positively impacted Symbiodiniaceae core photosynthetic health (photosystem II [PSII] quantum yield) and photoprotective capacity (non-photochemical quenching; NPQ) compared to cultures with all extracellular bacteria removed, although specific benefits were variable across Symbiodiniaceae genera and growth phase. Symbiodiniaceae co-cultured with M. aquimarina displayed an inverse NPQ response under high temperatures and light, and those with L. alexandrii demonstrated a lowered threshold for induction of NPQ, potentially through the provision of antioxidant compounds such as zeaxanthin (produced by Muricauda spp.) and dimethylsulfoniopropionate (DMSP; produced by this strain of L. alexandrii). Our co-culture approach empirically demonstrates the benefits bacteria can deliver to Symbiodiniaceae photochemical performance, providing evidence that bacterial associates can play important functional roles for Symbiodiniaceae.

Phenomics: conceptualization and importance for plant physiology.

Phenomics is a relatively new discipline of biology that has been widely applied in several fields, mainly in crop sciences. We reviewed the concepts used in this discipline (particularly for plants) and found a lack of consensus on what defines a phenomic study. Furthermore, phenomics has been primarily developed around its technical aspects (operationalization), while the conceptual framework of the actual research lags behind. Each research group has given its own interpretation of this 'omic' and thus unwittingly created a 'conceptual controversy'. Addressing this issue is of particular importance, as the experimental designs and concepts of phenomics are so diverse that it is difficult to compare studies. In this opinion article, we evaluate the conceptual framework of phenomics.

Save the planet with green industries using algae.

We can use photosynthesis to capture carbon and make industries greener. Algae-driven carbon capture and manufacturing offer the potential for reducing CO2 emissions while also producing commodities such as bioplastics.

Temperature mapping of non-photochemical quenching in Chlorella vulgaris.

Light intensity and temperature independently impact all parts of the photosynthetic machinery in plants and algae. Yet to date, the vast majority of pulse amplitude modulated (PAM) chlorophyll a fluorescence measurements have been performed at well-defined light intensities, but rarely at well-defined temperatures. In this work, we show that PAM measurements performed at various temperatures produce vastly different results in the chlorophyte Chlorella vulgaris. Using a recently developed Phenoplate technique to map quantum yield of Photosystem II (Y(II)) and non-photochemical quenching (NPQ) as a function of temperature, we show that the fast-relaxing NPQ follows an inverse normal distribution with respect to temperature and appears insensitive to previous temperature acclimation. The slow-relaxing or residual NPQ after 5 minutes of dark recovery follows a normal distribution similar to Y(II) but with a peak in the higher temperature range. Surprisingly, higher slow- and fast-relaxing NPQ values were observed in high-light relative to low-light acclimated cultures. Y(II) values peaked at the adaptation temperature regardless of temperature or light acclimation. Our novel findings show the complete temperature working spectrum of Y(II) and how excess energy quenching is managed across a wide range of temperatures in the model microalgal species C. vulgaris. Finally, we draw attention to the fact that the effect of the temperature component in PAM measurements has been wildly underestimated, and results from experiments at room temperature can be misleading.

Effects of harvesting on morphological and biochemical characteristics of microalgal biomass harvested by polyacrylamide addition, pH-induced flocculation, and centrifugation.

The effects of microalgae harvesting methods on microalgal biomass quality were evaluated using three species namely the freshwater green alga Chlorella vulgaris, marine red alga Porphyridium purpureum and marine diatom Phaeodactylum tricornutum. Harvesting efficiencies of polyacrylamide addition, alkaline addition, and centrifugation ranged from 85 to 95, 59-92 and 100%, respectively, across these species. Morphology of the harvested cells (i.e. compromised cell walls) was significantly impacted by alkaline pH-induced flocculation for all three species. Over 50% of C. vulgaris cells were compromised with alkaline pH compared to < 10% with polyacrylamide and centrifugation. The metabolic profiles varied depending on harvesting methods. Species-specific decrease of certain metabolites was observed. These results suggest that the method of harvest can alter the metabolic profile of the biomass amongst the three harvesting methods, polyacrylamide addition showed higher harvesting efficiency with less compromised cells and higher retention of industry important biochemicals.

Ecotoxicological response of Spirulina platensis to coexisted copper and zinc in anaerobic digestion effluent.

Copper ion (Cu2+) and zinc ion (Zn2+) are widely co-existent in anaerobic digestion effluent as typical contaminants. This work aims to explore how Cu2+-Zn2+ association affects physiological properties of S. platensis using Schlösser medium (SM) and sterilized anaerobic digestion effluent (SADE). Microalgae cells viability, biochemical properties, uptake of Cu2+ and Zn2+, and risk assessment associated with the biomass reuse as additives to pigs were comprehensively assessed. Biomass production ranged from 0.03 to 0.28 g/L in SM and 0.63 to 0.79 g/L in SADE due to the presence of Cu2+ and Zn2+. Peak value of chlorophyll-a and carotenoid content during the experiment decreased by 70-100% and 40-100% in SM, and by 70-77% and 30-55% in SADE. Crude protein level reduced by 4-41% in SM and by 65-75% in SADE. The reduction ratio of these compounds was positively related to the Cu2+ and Zn2+ concentrations. Maximum value of saturated and unsaturated fatty acids was both obtained at 0.3 Cu + 2.0 Zn (50.8% and 22.8%, respectively) and 25% SADE reactors (33.8% and 27.7%, respectively). Uptake of Cu in biomass was facilitated by Zn2+ concentration (> 4.0 mg/L). Risk of S. platensis biomass associated with Cu2+ was higher than Zn2+. S. platensis from SM (Cu2+ ≤ 0.3 mg/L and Zn2+ ≤ 4.0 mg/L) and diluted SADE (25% and 50% SADE) reactors could be used as feed additives without any risk (hazard index <1), which provides sufficient protein and fatty acids for pig consumption. These results revealed the promising application of using S. platensis for bioremediation of Cu2+ and Zn2+ in anaerobic digestion effluent and harvesting biomass for animal feed additives.

Unassembled cell wall proteins form aggregates in the extracellular space of Chlamydomonas reinhardtii strain UVM4.

The green microalga Chlamydomonas reinhardtii is emerging as a promising cell biofactory for secreted recombinant protein (RP) production. In recent years, the generation of the broadly used cell wall-deficient mutant strain UVM4 has allowed for a drastic increase in secreted RP yields. However, purification of secreted RPs from the extracellular space of C. reinhardtii strain UVM4 is challenging. Previous studies suggest that secreted RPs are trapped in a matrix of cell wall protein aggregates populating the secretome of strain UVM4, making it difficult to isolate and purify the RPs. To better understand the nature and behaviour of these extracellular protein aggregates, we analysed and compared the extracellular proteome of the strain UVM4 to its cell-walled ancestor, C. reinhardtii strain 137c. When grown under the same conditions, strain UVM4 produced a unique extracellular proteomic profile, including a higher abundance of secreted cell wall glycoproteins. Further characterization of high molecular weight extracellular protein aggregates in strain UVM4 revealed that they are largely comprised of pherophorins, a specific class of cell wall glycoproteins. Our results offer important new insights into the extracellular space of strain UVM4, including strain-specific secreted cell wall proteins and the composition of the aggregates possibly related to impaired RP purification. The discovery of pherophorins as a major component of extracellular protein aggregates will inform future strategies to remove or prevent aggregate formation, enhance purification of secreted RPs, and improve yields of recombinant biopharmaceuticals in this emerging cell biofactory. KEY POINTS: • Extracellular protein aggregates hinder purification of recombinant proteins in C. reinhardtii • Unassembled cell wall pherophorins are major components of extracellular protein aggregates • Known aggregate composition informs future strategies for recombinant protein purification.

Phenoplate: An innovative method for assessing interacting effects of temperature and light on non-photochemical quenching in microalgae under chemical stress.

Rapid light curves are one of the most widely used methods for assessing the physiological state of photosynthetic organisms. While the method has been applied in a range of physiological studies over the last 20 years, little progress has been made in adapting it for the new age of multi-parametric phenotyping. In order to advance research that is aimed at evaluating the physiological impact of multiple factors, the Phenoplate was developed: a simultaneous assessment of temperature and light gradients. It was used to measure rapid light curves of three marine microalgae across a temperature gradient and altered phosphate availability. The results revealed that activation of photoprotective mechanisms occurred with high efficiency at lower temperatures, and relaxation of photoprotection was negatively impacted above a certain temperature threshold in Tetraselmis sp. It was observed that Thalassiosira pseudonana and Nannochloropsis oceanica exhibited two unique delayed non-photochemical quenching signatures: in combinations of low light with low temperature, and darkness with high temperature, respectively. These findings demonstrate that the Phenoplate approach can be used as a rapid and simple tool to gain insight into the photobiology of microalgae.

High-throughput screening for heterotrophic growth in microalgae using the Biolog Plate assay.

Microalgae produce a broad range of organic compounds that are increasingly being recognised for their value in novel product production and biotechnological applications. Most microalgae are photoautotrophic, but some are capable of either mixotrophy or heterotrophy. Reported enhanced biomass yields or contrasting metabolite profiles compared to autotrophic growth improve the economics of large-scale production of microalgae, which currently limits industrial applications. Here, the potential of a high-throughput method for the rapid screening of microalgal metabolism was assessed against 95 different carbon sources, using the cost-effective Biolog plate. Of the 5 microalgae tested, Desmodesmus communis (30 carbon sources) and Chlorella vulgaris (19 carbon sources) had the highest number of positive responses to carbon sources, whereas Chlorella sorokiniana had the most negative (toxic) response to the various carbon sources (77 carbon sources). Comparison of Biolog plate results with traditional culture techniques showed good agreement. Species with a high number of positive responses on the Biolog plate exhibited the highest biomass yield under heterotrophic conditions, whilst those with low number of positive responses exhibited the highest biomass yield under autotrophic conditions, using traditional culturing techniques. While the use of these plates is limited to obtaining axenic lines of microalgal species, the method provided a high-throughput assessment of carbon source metabolism, without the expense of undertaking large, laborious traditional culturing assessments. Such high-throughput assessments can be regarded as useful tools for progressing species selection, metabolic capacity and optimal culture conditions for microalgal biotechnology applications.

Factors governing microalgae harvesting efficiency by flocculation using cationic polymers.

This study aims to elucidate the mechanisms governing the harvesting efficiency of Chlorella vulgaris by flocculation using a cationic polymer. Flocculation efficiency increased as microalgae culture matured (i.e. 35-45, 75, and > 97% efficiency at early, late exponential, and stationary phase, respectively. Unlike the negative impact of phosphate on flocculation in traditional wastewater treatment; here, phosphorous residue did not influence the flocculation efficiency of C. vulgaris. The observed dependency of flocculation efficiency on growth phase was driven by changes in microalgal cell properties. Microalgal extracellular polymeric substances (EPS) in both bound and free forms at stationary phase were two and three times higher than those at late and early exponential phase, respectively. Microalgae cells also became more negatively charged as they matured. Negatively charged and high EPS content together with the addition of high molecular weight and positively charged polymer could facilitate effective flocculation via charge neutralisation and bridging.

Seagrasses in an era of ocean warming: a review.

Seagrasses are valuable sources of food and habitat for marine life and are one of Earth's most efficient carbon sinks. However, they are facing a global decline due to ocean warming and eutrophication. In the last decade, with the advent of new technology and molecular advances, there has been a dramatic increase in the number of studies focusing on the effects of ocean warming on seagrasses. Here, we provide a comprehensive review of the future of seagrasses in an era of ocean warming. We have gathered information from published studies to identify potential commonalities in the effects of warming and the responses of seagrasses across four distinct levels: molecular, biochemical/physiological, morphological/population, and ecosystem/planetary. To date, we know that although warming strongly affects seagrasses at all four levels, seagrass responses diverge amongst species, populations, and over depths. Furthermore, warming alters seagrass distribution causing massive die-offs in some seagrass populations, whilst also causing tropicalization and migration of temperate species. In this review, we evaluate the combined effects of ocean warming with other environmental stressors and emphasize the need for multiple-stressor studies to provide a deeper understanding of seagrass resilience. We conclude by discussing the most significant knowledge gaps and future directions for seagrass research.

Corrigendum: Regional and Microenvironmental Scale Characterization of the Zostera muelleri Seagrass Microbiome.

[This corrects the article DOI: 10.3389/fmicb.2019.01011.].

Methyl Jasmonate and Methyl-ß-Cyclodextrin Individually Boost Triterpenoid Biosynthesis in Chlamydomonas Reinhardtii UVM4.

The commercialisation of valuable plant triterpenoids faces major challenges, including low abundance in natural hosts and costly downstream purification procedures. Endeavours to produce these compounds at industrial scale using microbial systems are gaining attention. Here, we report on a strategy to enrich the biomass of the biotechnologically-relevant Chlamydomonas reinhardtii strain UVM4 with valuable triterpenes, such as squalene and (S)-2,3-epoxysqualene. C. reinhardtii UVM4 was subjected to the elicitor compounds methyl jasmonate (MeJA) and methyl-ß-cyclodextrine (MßCD) to increase triterpene yields. MeJA treatment triggered oxidative stress, arrested growth, and altered the photosynthetic activity of the cells, while increasing squalene, (S)-2,3-epoxysqualene, and cycloartenol contents. Applying MßCD to cultures of C. reinhardtii lead to the sequestration of the two main sterols (ergosterol and 7-dehydroporiferasterol) into the growth medium and the intracellular accumulation of the intermediate cycloartenol, without compromising cell growth. When MßCD was applied in combination with MeJA, it counteracted the negative effects of MeJA on cell growth and physiology, but no synergistic effect on triterpene yield was observed. Together, our findings provide strategies for the triterpene enrichment of microalgal biomass and medium.

Comparative Study Highlights the Potential of Spectral Deconvolution for Fucoxanthin Screening in Live Phaeodactylum tricornutum Cultures.

Microalgal biotechnology shows considerable promise as a sustainable contributor to a broad range of industrial avenues. The field is however limited by processing methods that have commonly hindered the progress of high throughput screening, and consequently development of improved microalgal strains. We tested various microplate reader and flow cytometer methods for monitoring the commercially relevant pigment fucoxanthin in the marine diatom Phaeodactylum tricornutum. Based on accuracy and flexibility, we chose one described previously to adapt to live culture samples using a microplate reader and achieved a high correlation to HPLC (R2 = 0.849), effectively removing the need for solvent extraction. This was achieved by using new absorbance spectra inputs, reducing the detectable pigment library and changing pathlength values for the spectral deconvolution method in microplate reader format. Adaptation to 384-well microplates and removal of the need to equalize cultures by density further increased the screening rate. This work is of primary interest to projects requiring detection of biological pigments, and could theoretically be extended to other organisms and pigments of interest, improving the viability of microalgae biotechnology as a contributor to sustainable industry.

A comprehensive analysis of an effective flocculation method for high quality microalgal biomass harvesting.

Flocculation is a low-cost harvesting technique for microalgae biomass production, but flocculation efficiency is species dependent. In this study, we investigated the efficacy of two synthetic (polyacrylamide) and one natural (chitosan) flocculants against three algal species: the cyanobacterium Synechocystis sp., the freshwater Chlorella vulgaris, and the marine Phaeodactylum tricornutum at laboratory and pilot scales to evaluate harvesting efficiency, biomass integrity and media recycling. Growth phase affected the harvesting efficiency of the eukaryotic microalgae. The flocculation was optimal at stationary phase with high flocculation efficiency achieved using polyacrylamides at 24-36 mg/g dry weight. The effect of the flocculants on the harvested biomass was investigated. The flocculated Synechocystis sp. showed a higher proportion of compromised cells compared to C. vulgaris and P. tricornutum likely due to differences in cell walls composition. Compromised cells could lead to the release of valuable products into the surrounding growth media during flocculation. The residual culture media was recycled once with no impact on cell growth for all treatments and algal species. The flocculation technique was demonstrated at pilot-scale using 350 L microalgal suspension, showing an efficiency of 82-90% at a polyacrylamide dosage of 6.5-10 mg/L. This efficiency and the biomass quality are comparable to the laboratory-scale results. Overall, results indicate that polyacrylamide flocculants work on a wide range of species without the need for pre-treatment. The information generated in this study can contribute to making the microalgae industry more competitive.