Uncontrollable zinc (Zn) plating and hydrogen evolution greatly undermine Zn anode reversibility. Previous electrolyte designs focus on suppressing H2O reactivity, however, the accumulation of alkaline byproducts during battery calendar aging and cycling still deteriorates the battery performance. Here, we present a direct strategy to tackle such problems using a strong Brønsted acid, bis(trifluoromethanesulfonyl)imide (HTFSI), as the electrolyte additive. This approach reformulates battery interfacial chemistry on both electrodes, suppresses continuous corrosion reactions and promotes uniform Zn deposition. The enrichment of hydrophobic TFSI- anions at the Zn|electrolyte interface creates an H2O-deficient micro-environment, thus inhibiting Zn corrosion reactions and inducing a ZnS-rich interphase. This highly acidic electrolyte demonstrates high Zn plating/stripping Coulombic efficiency up to 99.7% at 1 mA cm-2 ( > 99.8% under higher current density and areal capacity). Additionally, Zn | |ZnV6O9 full cells exhibit a high capacity retention of 76.8% after 2000 cycles.
In response to societal developments and the growing demand for high-energy-density battery systems, alkali metal batteries (AMBs) have emerged as promising candidates for next-generation energy storage. Despite their high theoretical specific capacity and output voltage, AMBs face critical challenges related to high reactivity with electrolytes and unstable interphases. This review, from the perspective of electrolytes, analyzes AMB failure mechanisms, including interfacial side reactions, active materials loss, and metal dendrite growth. It then reviews recent advances in innovative electrolyte molecular designs, such as ether, ester, sulfone, sulfonamide, phosphate, and salt, aimed at overcoming the above-mentioned challenges. Finally, we propose the current molecular design principles and future promising directions that can help future precise electrolyte molecular design.
Constraining the electrochemical reactivity of free solvent molecules is pivotal for developing high-voltage lithium metal batteries, especially for ether solvents with high Li metal compatibility but low oxidation stability ( <4.0 V vs Li+/Li). The typical high concentration electrolyte approach relies on nearly saturated Li+ coordination to ether molecules, which is confronted with severe side reactions under high voltages ( >4.4 V) and extensive exothermic reactions between Li metal and reactive anions. Herein, we propose a molecular anchoring approach to restrict the interfacial reactivity of free ether solvents in diluted electrolytes. The hydrogen-bonding interactions from the anchoring solvent effectively suppress excessive ether side reactions and enhances the stability of nickel rich cathodes at 4.7 V, despite the extremely low Li+/ether molar ratio (1:9) and the absence of typical anion-derived interphase. Furthermore, the exothermic processes under thermal abuse conditions are mitigated due to the reduced reactivity of anions, which effectively postpones the battery thermal runaway.
A 3D host design for lithium (Li)-metal anodes can effectively accommodate volume changes and suppress Li dendrite growth; nonetheless, its practical applicability in energy-dense Li-metal batteries (LMBs) is plagued by excessive Li loading. Herein, we introduced eco- and human-friendly Se seeds into 3D carbon cloth (CC) to create a robust host for efficient Li deposition/stripping. The highly lithiophilic nano-Se endowed the Se-decorated CC (Se@CC) with perfect Li wettability for instantaneous Li infusion. At an optimal Li loading of 17 mg, the electrode delivered an unprecedentedly long life span of 5400 h with low overpotentials <36 mV at 1 mA cm-2/1 mAh cm-2 and 1500 h at 5 mA cm-2/5 mAh cm-2. Furthermore, the uniform Se distribution and strong Li-Se binding allowed for further reduction in Li loading to 2 mg via direct Li electrodeposition. The corresponding LiNi0.8Co0.1Mn0.1O2 (NCM811)-based full cell afforded a high capacity retention rate of 74.67% over 300 cycles at a low N/P ratio of 8.64. Finally, the initial anode-free LMB using a NCM811 cathode and a Se@CC anode current collector demonstrated a high electrode-level specific energy of 531 Wh kg-1 and consistently high CEs >99.7% over 200 cycles. This work highlights a high-performance host design with excellent tunability for practical high-energy-density LMBs.
LiCoO2 (LCO) cathode materials have attracted significant attention for its potential to provide higher energy density in current Lithium-ion batteries (LIBs). However, the structure and performance degradation are exacerbated by increasing voltage due to the catastrophic reaction between the applied electrolyte and delithiated LCO. The present study focuses on the construction of physically and chemically robust Mg-integrated cathode-electrolyte interface (MCEI) to address this issue, by incorporating Magnesium bis(trifluoromethanesulfonyl)imide (Mg[TFSI]2 ) as an electrolyte additive. During formation cycles, the strong MCEI is formed and maintained its 2 nm thickness throughout long-term cycling. Notably, Mg is detected not only in the robust MCEI, but also imbedded in the surface of the LCO lattice. As a result, the parasitic interfacial side reactions, surface phase reconstruction, particle cracking, Co dissolution and shuttling are considerably suppressed, resulting in long-term cycling stability of LCO up to 4.5 V. Therefore, benefit from the double protection of the strong MCEI, the Li||LCO coin cell and the Ah-level Graphite||LCO pouch cell exhibit high capacity retention by using Mg-electrolyte, which are 88.13% after 200 cycles and 90.4% after 300 cycles, respectively. This work provides a novel approach for the rational design of traditional electrolyte additives.
The electrolyte solvation structure and the solid-electrolyte interphase (SEI) formation are critical to dictate the morphology of lithium deposition in organic electrolytes. However, the link between the electrolyte solvation structure and SEI composition and its implications on lithium morphology evolution are poorly understood. Herein, we use a single-salt and single-solvent model electrolyte system to systematically study the correlation between the electrolyte solvation structure, SEI formation process and lithium deposition morphology. The mechanism of lithium deposition is thoroughly investigated using cryo-electron microscopy characterizations and computational simulations. It is observed that, in the high concentration electrolytes, concentrated Li+ and anion-dominated solvation structure initiate the uniform Li nucleation kinetically and favor the decomposition of anions rather than solvents, resulting in inorganic-rich amorphous SEI with high interface energy, which thermodynamically facilitates the formation of granular Li. On the contrary, solvent-dominated solvation structure in the low concentration electrolytes tends to exacerbate the solvolysis process, forming organic-rich mosaic SEI with low interface energy, which leads to aggregated whisker-like nucleation and growth. These results are helpful to tackle the long-standing question on the origin of lithium dendrite formation and guide the rational design of high-performance electrolytes for advanced lithium metal batteries.
Electrolytes are critical for the reversibility of various electrochemical energy storage systems. The recent development of electrolytes for high-voltage Li-metal batteries has been counting on the salt anion chemistry for building stable interphases. Herein, we investigate the effect of the solvent structure on the interfacial reactivity and discover profound solvent chemistry of designed monofluoro-ether in anion-enriched solvation structures, which enables enhanced stabilization of both high-voltage cathodes and Li-metal anodes. Systematic comparison of different molecular derivatives provides an atomic-scale understanding of the unique solvent structure-dependent reactivity. The interaction between Li+ and the monofluoro (-CH2F) group significantly influences the electrolyte solvation structure and promotes the monofluoro-ether-based interfacial reactions over the anion chemistry. With in-depth analyses of the compositions, charge transfer, and ion transport at interfaces, we demonstrated the essential role of the monofluoro-ether solvent chemistry in tailoring highly protective and conductive interphases (with enriched LiF at full depths) on both electrodes, as opposed to the anion-derived ones in typical concentrated electrolytes. As a result, the solvent-dominant electrolyte chemistry enables a high Li Coulombic efficiency (â¼99.4%) and stable Li anode cycling at a high rate (10 mA cm-2), together with greatly improved cycling stability of 4.7 V-class nickel-rich cathodes. This work illustrates the underlying mechanism of the competitive solvent and anion interfacial reaction schemes in Li-metal batteries and offers fundamental insights into the rational design of electrolytes for future high-energy batteries.
Albeit ethers are favorable electrolyte solvents for lithium (Li) metal anode, their inferior oxidation stability (<4.0â V vs. Li/Li+ ) is problematic for high-voltage cathodes. Studies of ether electrolytes have been focusing on the archetype glyme structure with ethylene oxide moieties. Herein, we unveil the crucial effect of ion coordination configuration on oxidation stability by varying the ether backbone structure. The designed 1,3-dimethoxypropane (DMP, C3) forms a unique six-membered chelating complex with Li+ , whose stronger solvating ability suppresses oxidation side reactions. In addition, the favored hydrogen transfer reaction between C3 and anion induces a dramatic enrichment of LiF (a total atomic ratio of 76.7 %) on the cathode surface. As a result, the C3-based electrolyte enables greatly improved cycling of nickel-rich cathodes under 4.7â V. This study offers fundamental insights into rational electrolyte design for developing high-energy-density batteries.
Ethers are promising electrolytes for lithium (Li) metal batteries (LMBs) because of their unique stability with Li metal. Although intensive research on designing anion-enriched electrolyte solvation structures has greatly improved their electrochemical stabilities, ether electrolytes are approaching an anodic bottleneck. Herein, we reveal the strong correlation between electrolyte solvation structure and oxidation stability. In contrast to previous designs of weakly solvating solvents for enhanced anion reactivities, the triglyme (G3)-based electrolyte with the largest Li+ solvation energy among different linear ethers demonstrates greatly improved stability on Ni-rich cathodes under an ultrahigh voltage of 4.7 V (93% capacity retention after 100 cycles). Ether electrolytes with a stronger Li+ solvating ability could greatly suppress deleterious oxidation side reactions by decreasing the lifetime of free labile ether molecules. This study provides critical insights into the dynamics of the solvation structure and its significant influence on the interfacial stability for future development of high-efficiency electrolytes for high-energy-density LMBs.
Electrocatalytic CO2 reduction reaction (CO2RR) is one of the most promising routes to facilitate carbon neutrality. An alkaline electrolyte is typically needed to promote the production of valuable multi-carbon molecules (such as ethylene). However, the reaction between CO2 and OH- consumes a significant quantity of CO2/alkali and causes the rapid decay of CO2RR selectivity and stability. Here, we design a catalyst-electrolyte interface with an effective electrostatic confinement of in situ generated OH- to improve ethylene electrosynthesis from CO2 in neutral medium. In situ Raman measurements indicate the direct correlation between ethylene selectivity and the intensities of surface Cu-CO and Cu-OH species, suggesting the promoted C-C coupling with the surface enrichment of OH-. Thus, we report a CO2-to-ethylene Faradaic efficiency (FE) of 70% and a partial current density of 350 mA cm-2 at -0.89 V vs the reversible hydrogen electrode. Furthermore, the system demonstrated a 50 h stable operation at 300 mA cm-2 with an average ethylene FE of â¼68%. This study offers a universal strategy to tune the reaction micro-environment, and a significantly improved ethylene FE of 64.5% was obtained even in acidic electrolytes (pH = 2).
Nonflammable electrolytes are critical for the safe operation of high-voltage lithium-ion batteries (LIBs). Although organic phosphates are effective flame retardants, their poor electrochemical stability with a graphite (Gr) anode and Ni-rich cathodes would lead to the deterioration of electrode materials and fast capacity decay. Herein, we develop a safe and high-performance electrolyte formulation for high-voltage (4.6 V-class) LIBs using flame-retarding ethoxy(pentafluoro) cyclotriphosphazene (PFPN) as a non-solvating diluent for the high-concentration carbonate-ether hybrid electrolyte. In contrast to conventional nonflammable additives with restricted dosage, the high level of PFPN (69% mass ratio in our electrolyte design) could significantly increase the electrolyte flash point and protect the favored anion-rich inner solvation sheath because of its non-solvating feature, thus preventing solvent co-intercalation and structural damage to the Gr anode. The nonflammable electrolyte could also form a stable LiF-rich cathode electrolyte interphase (CEI), which enables superior electrochemical performances of GrâLiNi0.8Mn0.1Co0.1O2 (NMC811) full cells at high voltages (â¼82.0% capacity retention after 1000 cycles at 4.5 V; 89.8% after 300 cycles at 4.6 V) and high temperatures (50 °C). This work sheds light on the electrolyte design and interphase engineering for developing practical safe high-energy-density LIBs.
Electrolyte freezing under low temperatures is a critical challenge for the development of aqueous batteries (ABs). While lowering the freezing point of the electrolyte has caught major research efforts, limited attention has been paid to the structural evolution during the electrolyte freezing process and regulating the frozen electrolyte structure for low temperature ABs. Here, we reveal the formation process of interconnected liquid regions for ion transport in frozen electrolytes with various in situ variable-temperature technologies. More importantly, the low-temperature performance of ABs was significantly improved with the colloidal electrolyte design using graphene oxide quantum dots (GOQDs), which effectively inhibits the growth of ice crystals and expands the interconnected liquid regions for facial ion transport. This work provides new insights and a promising strategy for the electrolyte design of low-temperature ABs.
Despite the promises in high-energy-density batteries, Li-metal anodes (LMAs) have suffered from extensive electrolyte decomposition and unlimited volume expansion owing to thick, porous layer buildup during cycling. It mainly originates from a ceaseless reiteration of the formation and collapse of solid-electrolyte interphase (SEI). This study reveals the structural and chemical evolutions of the reacted Li layer after different cycles and investigates its detrimental effects on the cycling stability under practical conditions. Instead of the immediately deactivated top surface of the reacted Li layer, the chemical nature underneath the reacted Li layer can be an important indicator of the electrolyte compositional changes. It is found that cycling of LMAs with a lean electrolyte (≈3 g Ah-1 ) causes fast depletion of salt anions, leading to the dynamic evolution of the reacted Li layer structure and composition. Increasing the salt-solvent complex while reducing the non-solvating diluent retards the rate of depletion in a localized high-concentration electrolyte, thereby demonstrating prolonged cycling of Li||NMC622 cells without compromising the Li Coulombic efficiencies and high-voltage stability.
Rechargeable potassium-oxygen batteries (KOB) are promising next-generation energy storage devices because of the highly reversible O2/O2- redox reactions during battery charge and discharge. However, the complicated cathode reaction processes seriously jeopardize the battery reaction kinetics and discharge capacity. Herein, we propose a hybrid-solvent strategy to effectively tune the K+ solvation structure, which demonstrates a critical influence on the charge-transfer kinetics and cathode reaction mechanism. The cosolvation of K+ by 1,2-dimethoxyethane (DME) and dimethyl sulfoxide (DMSO) could greatly decrease overpotentials for the cathode processes and increase the cathode discharge capacity. Furthermore, the Coulombic efficiency for the cathode could be significantly improved with the enhanced solution-mediated KO2 growth and stripping during cycling. This work provides a promising electrolyte design approach to improve the electrochemical performance of the KOB.
Solid electrolytes hold promise in safely enabling high-energy metallic sodium (Na) anodes. However, the poor Naâsolid electrolyte interfacial contact can induce Na dendrite growth and limit Na utilization, plaguing the rate performance and energy density of current solid-state Na-metal batteries (SSSMBs). Herein, a simple and scalable Pb/C interlayer strategy is introduced to regulate the surface chemistry and improve Na wettability of Na3Zr2Si2PO12 (NZSP) solid electrolyte. The resulting NZSP exhibits a perfect Na wettability (0° contact angle) at a record-low temperature of 120 °C, a negligible room-temperature NaâNZSP interfacial resistance of 1.5 Ω cm2, along with an ultralong cycle life of over 1800 h under 0.5 mA cm-2/0.5 mA h cm-2 symmetric cell cycling at 55 °C. Furthermore, we unprecedentedly demonstrate in situ fabrication of weight-controlled Na anodes and explore the effect of the negative/positive capacity (N/P) ratio on the cyclability of SSSMBs. Both solid-state Na3V2(PO4)3 and S full cells show superior electrochemical performance at an optimal N/P ratio of 40.0. The Pb/C interlayer modification demonstrates dual functions of stabilizing the anode interface and improving Na utilization, making it a general strategy for implementing Na metal anodes in practical SSSMBs.
Significant challenges remain in developing rechargeable zinc batteries mainly because of reversibility problems on zinc-metal anodes. The dendritic growth and hydrogen evolution on zinc electrodes are major obstacles to overcome in developing practical and safe zinc batteries. Here, a dendrite-free and hydrogen-free Zn-metal anode with high Coulombic efficiency up to 99.6% over 300 cycles is realized in a newly designed nonaqueous electrolyte, which comprises an inexpensive zinc salt, zinc acetate, and a green low-cost solvent, dimethyl sulfoxide. Surface transformation on Cu substrate plays a critical role in facilitating the dendrite-free deposition process, which lowers the diffusion energy barrier of the Zn atoms, leading to a uniform and compact thin film for zinc plating. Furthermore, in situ electrochemical atomic force microscopy reveals the plating process via a layer-by-layer growth mechanism and the stripping process through an edge-dissolution mechanism. In addition, Zn||Mo6 S8 full cells exhibit excellent electrochemical performance in terms of cycling stability and rate capability. This work presents a new opportunity to develop nonaqueous rechargeable zinc batteries.
Solid-state electrolytes (SSEs) hold a critical role in enabling high-energy-density and safe rechargeable batteries with Li metal anode. Unfortunately, nonuniform lithium deposition and dendrite penetration due to poor interfacial solid-solid contact are hindering their practical applications. Here, solid-state lithium naphthalenide (Li-Naph(s)) is introduced as a plastic monolithic mixed-conducting interlayer (PMMCI) between the garnet electrolyte and the Li anode via a facile cold process. The thin PMMCI shows a well-ordered layered crystalline structure with excellent mixed-conducting capability for both Li+ (4.38 × 10-3 S cm-1 ) and delocalized electrons (1.01 × 10-3 S cm-1 ). In contrast to previous composite interlayers, this monolithic material enables an intrinsically homogenous electric field and Li+ transport at the Li/garnet interface, thus significantly reducing the interfacial resistance and achieving uniform and dendrite-free Li anode plating/stripping. As a result, Li symmetric cells with the PMMCI-modified garnet electrolyte show highly stable cycling for 1200 h at 0.2 mA cm-2 and 500 h at a high current density of 1 mA cm-2 . The findings provide a new interface design strategy for solid-state batteries using monolithic mixed-conducting interlayers.
The issues of inherent low anodic stability and high flammability hinder the deployment of the ether-based electrolytes in practical high-voltage lithium metal batteries. Here, we report a rationally designed ether-based electrolyte with chlorine functionality on ether molecular structure to address these critical challenges. The chloroether-based electrolyte demonstrates a high Li Coulombic efficiency of 99.2 % and a high capacity retention >88 % over 200â cycles for Ni-rich cathodes at an ultrahigh cut-off voltage of 4.6â V (stable even up to 4.7â V). The chloroether-based electrolyte not only greatly improves electrochemical stabilities of Ni-rich cathodes under ultrahigh voltages with interphases riched in LiF and LiCl, but possesses the intrinsic nonflammable safety feature owing to the flame-retarding ability of chlorine functional groups. This study offers a new approach to enable ether-based electrolytes for high energy density, long-life and safe Li metal batteries.
The water-in-salt electrolyte (WISE) features intimate interactions between a cation and anion, which induces the formation of an anion-derived solid electrolyte interphase (SEI) and expands the aqueous electrolyte voltage window to >3.0 V. Although further increasing the salt concentration (even to >60 molality (m)) can gradually improve water stability, issues about cost and practical feasibility are concerned. An alternative approach is to intensify ion-solvent interactions in the inner solvation structure by shielding off outward electrostatic attractions from nearby ions. Here, we design an "overcrowded" electrolyte using the non-polar, hydrogen-bonding 1,4-dioxane (DX) as an overcrowding agent, thereby achieving a robust LiF-enriched SEI and wide electrolyte operation window (3.7 V) with a low salt concentration (<2 m). As a result, the electrochemical performance of aqueous Li4Ti5O12/LiMn2O4 full cells can be substantially improved (88.5% capacity retention after 200 cycles, at 0.57 C). This study points out a promising strategy to develop low-cost and stable high-voltage aqueous batteries.
Electrolyte is very critical to the performance of the high-voltage lithium (Li) metal battery (LMB), which is one of the most attractive candidates for the next-generation high-density energy-storage systems. Electrolyte formulation and structure determine the physical properties of the electrolytes and their interfacial chemistries on the electrode surfaces. Localized high-concentration electrolytes (LHCEs) outperform state-of-the-art carbonate electrolytes in many aspects in LMBs due to their unique solvation structures. Types of fluorinated cosolvents used in LHCEs are investigated here in searching for the most suitable diluent for high-concentration electrolytes (HCEs). Nonsolvating solvents (including fluorinated ethers, fluorinated borate, and fluorinated orthoformate) added in HCEs enable the formation of LHCEs with high-concentration solvation structures. However, low-solvating fluorinated carbonate will coordinate with Li+ ions and form a second solvation shell or a pseudo-LHCE which diminishes the benefits of LHCE. In addition, it is evident that the diluent has significant influence on the electrode/electrolyte interphases (EEIs) beyond retaining the high-concentration solvation structures. Diluent molecules surrounding the high-concentration clusters could accelerate or decelerate the anion decomposition through coparticipation of diluent decomposition in the EEI formation. The varied interphase features lead to significantly different battery performance. This study points out the importance of diluents and their synergetic effects with the conductive salt and the solvating solvent in designing LHCEs. These systematic comparisons and fundamental insights into LHCEs using different types of fluorinated solvents can guide further development of advanced electrolytes for high-voltage LMBs.
