Hard X-ray full-field nanoimaging using a direct photon-counting detector.

Full-field X-ray nanoimaging is a widely used tool in a broad range of scientific areas. In particular, for low-absorbing biological or medical samples, phase contrast methods have to be considered. Three well established phase contrast methods at the nanoscale are transmission X-ray microscopy with Zernike phase contrast, near-field holography and near-field ptychography. The high spatial resolution, however, often comes with the drawback of a lower signal-to-noise ratio and significantly longer scan times, compared with microimaging. In order to tackle these challenges a single-photon-counting detector has been implemented at the nanoimaging endstation of the beamline P05 at PETRA III (DESY, Hamburg) operated by Helmholtz-Zentrum Hereon. Thanks to the long sample-to-detector distance available, spatial resolutions of below 100 nm were reached in all three presented nanoimaging techniques. This work shows that a single-photon-counting detector in combination with a long sample-to-detector distance allows one to increase the time resolution for in situ nanoimaging, while keeping a high signal-to-noise level.

Real-time insight into nanostructure evolution during the rapid formation of ultra-thin gold layers on polymers.

Ultra-thin metal layers on polymer thin films attract tremendous research interest for advanced flexible optoelectronic applications, including organic photovoltaics, light emitting diodes and sensors. To realize the large-scale production of such metal-polymer hybrid materials, high rate sputter deposition is of particular interest. Here, we witness the birth of a metal-polymer hybrid material by quantifying in situ with unprecedented time-resolution of 0.5 ms the temporal evolution of interfacial morphology during the rapid formation of ultra-thin gold layers on thin polystyrene films. We monitor average non-equilibrium cluster geometries, transient interface morphologies and the effective near-surface gold diffusion. At 1 s sputter deposition, the polymer matrix has already been enriched with 1% gold and an intermixing layer has formed with a depth of over 3.5 nm. Furthermore, we experimentally observe unexpected changes in aspect ratios of ultra-small gold clusters growing in the vicinity of polymer chains. For the first time, this approach enables four-dimensional insights at atomic scales during the gold growth under non-equilibrium conditions.

Following In Situ the Evolution of Morphology and Optical Properties during Printing of Thin Films for Application in Non-Fullerene Acceptor Based Organic Solar Cells.

In situ printing gives insight into the evolution of morphology and optical properties during slot-die coating of active layers for application in organic solar cells and enables an upscaling and optimization of the thin film deposition process and the photovoltaic performance. Active layers based on the conjugated polymer donor with benzodithiophene units PBDB-T-2Cl and the non-fullerene small-molecule acceptor IT-4F are printed with a slot-die coating technique and probed in situ with grazing incidence small-angle X-ray scattering, grazing incidence wide-angle X-ray scattering, and ultraviolet/visible light spectroscopy. The formation of the morphology is followed from the liquid state to the final dry film for different printing conditions (at 25 and 35 °C), and five regimes of film formation are determined. The morphological changes are correlated to changing optical properties. During the film formation, crystallization of the non-fullerene small-molecule acceptor takes place and polymer domains with sizes of some tens of nanometers emerge. A red shift of the optical band gap and a broadening of the absorbance spectrum occurs, which allow for exploiting the sun spectrum more efficiently and are expected to have a favorable effect on the solar cell performance.

Fast-current-heating devices to study in situ phase formation in metallic glasses by using high-energy synchrotron radiation.

Details of fast-resistive-heating setups, controlled heating ranging from ∼101 K s-1 to ∼103 K s-1, to study in situ phase transformations (on heating and on cooling) in metallic glasses by high-energy synchrotron x-ray diffraction are discussed. Both setups were designed and custom built at the Leibniz Institute for Solid State and Materials Research Dresden (IFW Dresden) and have been implemented at the P02.1 Powder Diffraction and Total Scattering Beamline and the P21.1 Swedish Materials Science Beamline at PETRA III storage ring, DESY, Hamburg. The devices are interchangeable at both beamlines. Joule heating is triggered automatically and is timed with the incident beam and detector. The crystallization process can be controlled via a feedback circuit by monitoring the change in the time-dependent resistivity and temperature of glasses. Different ambient atmospheres, such as vacuum and inert gases (He and Ar), can be used to control oxidation and cooling. The main focus of these devices is on understanding the crystallization mechanism and kinetics in metallic glasses, which are brittle and for which fast heating gives defined glass-crystal composites with enhanced plasticity. As an example, phase-transformation sequence(s) in a prototyped Cu-Zr-based metallic glass is described on heating, and a crystalline phase beneficial to the plasticity is identified.

Crystal growth rates in supercooled atomic liquid mixtures.

Crystallization is a fundamental process in materials science, providing the primary route for the realization of a wide range of new materials. Crystallization rates are also considered to be useful probes of glass-forming ability1-3. At the microscopic level, crystallization is described by the classical crystal nucleation and growth theories4,5, yet in general solid formation is a far more complex process. In particular, the observation of apparently different crystal growth regimes in many binary liquid mixtures greatly challenges our understanding of crystallization1,6-12. Here, we study by experiments, theory and computer simulations the crystallization of supercooled mixtures of argon and krypton, showing that crystal growth rates in these systems can be reconciled with existing crystal growth models only by explicitly accounting for the non-ideality of the mixtures. Our results highlight the importance of thermodynamic aspects in describing the crystal growth kinetics, providing a substantial step towards a more sophisticated theory of crystal growth.

Structure-Function Correlations in Sputter Deposited Gold/Fluorocarbon Multilayers for Tuning Optical Response.

A new strategy to nanoengineer gold/fluorocarbon multilayer (ML) nanostructures is reported. We have investigated the morphological changes occurring at the metal-polymer interface in ML structures with varying volume fraction of gold (Au) and the kinetic growth aspect of the microscale properties of nano-sized Au in plasma polymer fluorocarbon (PPFC). Investigations were carried out at various temperatures and annealing times by means of grazing incidence small-angle and wide-angle X-ray scattering (GISAXS and GIWAXS). We have fabricated a series of MLs with varying volume fraction (0.12, 0.27, 0.38) of Au and bilayer periodicity in ML structure. They show an interesting granular structure consisting of nearly spherical nanoparticles within the polymer layer. The nanoparticle (NP) morphology changes due to the collective effects of NPs diffusion within ensembles in the in-plane vicinity and interlayer with increasing temperature. The in-plane NPs size distinctly increases with increasing temperature. The NPs become more spherical, thus reducing the surface energy. Linear growth of NPs with temperature and time shows diffusion-controlled growth of NPs in the ML structure. The structural stability of the multilayer is controlled by the volume ratio of the metal in polymer. At room temperature, UV-Vis shows a blue shift of the plasmon peak from 560 nm in ML Au/PTFE_1 to 437 nm in Au/PTFE_3. We have identified the fabrication and postdeposition annealing conditions to limit the local surface plasmon resonance (LSPR) shift from Δ λ L S P R = 180 nm (Au/PTFE_1) to Δ λ L S P R = 67 nm (Au/PTFE_3 ML)) and their optical response over a wide visible wavelength range. A variation in the dielectric constant of the polymer in presence of varying Au inclusion is found to be a possible factor affecting the LSPR frequency. Our findings may provide insights in nanoengineering of ML structure that can be useful to systematically control the growth of NPs in polymer matrix.

Parallel and Perpendicular Alignment of Anisotropic Particles in Free Liquid Microjets and Emerging Microdroplets.

Liquid microjets play a key role in fiber spinning, inkjet printing, and coating processes. In all of these applications, the liquid jets carry dispersed particles whose spatial and orientational distributions within the jet critically influence the properties of the fabricated structures. Despite its importance, there is currently no knowledge about the orientational distribution of particles within microjets and droplets. Here, we demonstrate a microfluidic device that allows to determine the local particle distribution and orientation by X-ray scattering. Using this methodology, we discovered unexpected changes in the particle orientation upon exiting the nozzle to form a free jet, and upon jet break-up into droplets, causing an unusual biaxial particle orientation. We show how flow and aspect ratio determine the flow orientation of anisotropic particles. Furthermore, we demonstrate that the observed phenomena are a general characteristic of anisotropic particles. Our findings greatly enhance our understanding of particle orientation in free jets and droplets and provide a rationale for controlling particle alignment in liquid jet-based fabrication methodologies.

Transmission zone plates as analyzers for efficient parallel 2D RIXS-mapping.

We have implemented and successfully tested an off-axis transmission Fresnel zone plate as spectral analyzer for resonant inelastic X-ray scattering (RIXS). The imaging capabilities of zone plates allow for advanced two-dimensional (2D) mapping applications. By varying the photon energy along a line focus on the sample, we were able to simultaneously record the emission spectra over a range of excitation energies. Moreover, by scanning a line focus across the sample in one dimension, we efficiently recorded RIXS spectra spatially resolved in 2D, increasing the throughput by two orders of magnitude. The presented scheme opens up a variety of novel measurements and efficient, ultra-fast time resolved investigations at X-ray Free-Electron Laser sources.

Real-Time Monitoring of Morphology and Optical Properties during Sputter Deposition for Tailoring Metal-Polymer Interfaces.

The reproducible low-cost fabrication of functional metal-polymer nanocomposites with tailored optoelectronic properties for advanced applications remains a major challenge in applied nanotechnology. To obtain full control over the nanostructural evolution at the metal-polymer interface and its impact on optoelectronic properties, we employed combined in situ time-resolved microfocus grazing incidence small angle X-ray scattering (µGISAXS) with in situ UV/vis specular reflectance spectroscopy (SRS) during sputter deposition of gold on thin polystyrene films. On the basis of the temporal evolution of the key scattering features in the real-time µGISAXS experiment, we directly observed four different growth regimes: nucleation, isolated island growth, growth of larger aggregates via partial coalescence, and continuous layer growth. Moreover, their individual thresholds were identified with subnanometer resolution and correlated to the changes in optical properties. During sputter deposition, a change in optical reflectivity of the pristine gray-blue PS film was observed ranging from dark blue color due to the presence of isolated nanoclusters at the interface to bright red color from larger Au aggregates. We used simplified geometrical assumptions to model the evolution of average real space parameters (distance, size, density, contact angle) in excellent agreement with the qualitative observation of key scattering features. A decrease of contact angles was observed during the island-to-percolation transition and confirmed by simulations. Furthermore, a surface diffusion coefficient according to the kinetic freezing model and interfacial energy of Au on PS at room temperature were calculated based on a real-time experiment. The morphological characterization is complemented by X-ray reflectivity, optical, and electron microscopy. Our study permits a better understanding of the growth kinetics of gold clusters and their self-organization into complex nanostructures on polymer substrates. It opens up the opportunity to improve nanofabrication and tailoring of metal-polymer nanostructures for optoelectronic applications, organic photovoltaics, and plasmonic-enhanced technologies.

Size limit on the formation of periodic mesoporous organosilicas (PMOs).

The decrease of the lattice size of periodic mesoporous organosilicas (PMOs) is one important goal in obtaining a microporous material for storage or adsorption of small molecules. To determine the influence of different synthesis parameters in the lattice size, here we performed in situ small-angle X-ray diffraction studies and show that a variation of the surfactant's headgroup size is not directly followed by the lattice parameter of the resulting structure. We show that in the surfactant series of penta-, hexa-, hepta-, octa-, nona-, and decaethylene glycol monododecyl ether (C12(EO)n, n = 5, 6, 7, 8, 9, 10) the lattice size decreases between n = 5 and n = 8 and then increases, while the ordering of the materials is always cubic (space group Fd3m). This size effect is due to the ethylene oxide (EO) chain conformation that changes as the number of EO groups increases. Short ethylene oxide chains tend to have a so-called "zigzag" conformation while an increase of the chain length leads to a "Mäander" (coiling) conformation. Although this phenomenon is most commonly observed for chains consisting of more than 10 ethylene oxide units, we found a minimum PMO lattice size for 8 EO units and intermediate values for 6 and 7 EO units. The increase of the lattice parameter for more than 9 EO units is attributed to the increasing number of "Mäander" configurated EO units.

Single-crystal diffraction at the Extreme Conditions beamline P02.2: procedure for collecting and analyzing high-pressure single-crystal data.

Fast detectors employed at third-generation synchrotrons have reduced collection times significantly and require the optimization of commercial as well as customized software packages for data reduction and analysis. In this paper a procedure to collect, process and analyze single-crystal data sets collected at high pressure at the Extreme Conditions beamline (P02.2) at PETRA III, DESY, is presented. A new data image format called `Esperanto' is introduced that is supported by the commercial software package CrysAlis(Pro) (Agilent Technologies UK Ltd). The new format acts as a vehicle to transform the most common area-detector data formats via a translator software. Such a conversion tool has been developed and converts tiff data collected on a Perkin Elmer detector, as well as data collected on a MAR345/555, to be imported into the CrysAlis(Pro) software. In order to demonstrate the validity of the new approach, a complete structure refinement of boron-mullite (Al5BO9) collected at a pressure of 19.4 (2) GPa is presented. Details pertaining to the data collections and refinements of B-mullite are presented.

Aluminum-1,4-cyclohexanedicarboxylates: high-throughput and temperature-dependent in situ EDXRD studies.

The system AlCl3·6H2O/cis-H2CDC/trans-H2CDC/solvent was systematically investigated with high-throughput methods to study the influence of the two 1,4-cyclohexanedicarboxylate isomers (cis- and trans-H2CDC) as flexible aliphatic linker molecules on the formation of new crystalline compounds. Using the cis-isomer, the layered inorganic-organic hybrid compound [Al(OH)(cis-CDC)] (1) is formed. The use of trans-H2CDC leads to the microporous MOF [Al(OH)(trans-CDC)]·H2O (2) denoted CAU-13. Its framework is related to the well-known MIL-53, which was previously described for trivalent cations and rigid terephthalate linker molecules. The crystal structures of 1 and 2 were derived from powder X-ray diffraction data. Temperature-dependent in situ energy dispersive X-ray diffraction (EDXRD) experiments for the synthesis of 2 were carried out at HASYLAB, DESY, Hamburg. The kinetic analysis, applying the Gualtieri model to the experimental data, revealed Arrhenius activation energies of 76 kJ/mol for both the nucleation and the growth process. These values do not differ much from the activation energies reported for MOFs with aromatic rigid linker molecules.

From atoms to layers: in situ gold cluster growth kinetics during sputter deposition.

The adjustment of size-dependent catalytic, electrical and optical properties of gold cluster assemblies is a very significant issue in modern applied nanotechnology. We present a real-time investigation of the growth kinetics of gold nanostructures from small nuclei to a complete gold layer during magnetron sputter deposition with high time resolution by means of in situ microbeam grazing incidence small-angle X-ray scattering (µGISAXS). We specify the four-stage growth including their thresholds with sub-monolayer resolution and identify phase transitions monitored in Yoneda intensity as a material-specific characteristic. An innovative and flexible geometrical model enables the extraction of morphological real space parameters, such as cluster size and shape, correlation distance, layer porosity and surface coverage, directly from reciprocal space scattering data. This approach enables a large variety of future investigations of the influence of different process parameters on the thin metal film morphology. Furthermore, our study allows for deducing the wetting behavior of gold cluster films on solid substrates and provides a better understanding of the growth kinetics in general, which is essential for optimization of manufacturing parameters, saving energy and resources.

High-throughput microwave-assisted discovery of new metal phosphonates.

A systematic study was carried out to investigate the influence of linker geometry, metal ionic radius as well as the nature of the counter ions on the structure formation of metal tetraphosphonates. Two tetraphosphonic acids p- and m-(H2O3PCH2)2N-CH2-C6H4-CH2-N(CH2PO3H2)2, six metal ions (Ca(2+), Mn(2+), Co(2+), Ni(2+), Zn(2+), and Cd(2+)) and two different counter ions (Cl(-) and NO3(-)) were employed using high throughput methods. Microwave (MW)-assisted heating led to the discovery of ten new metal-phosphonates which crystallize in three different crystal structures. The combination of direct methods and force field calculations allowed us to establish the crystal structures. The counter ion and the ionic radii of the metal ions have a profound influence on the crystallinity and the formed crystal structure. All compounds were characterized in detail by thermogravimetric analyses, IR spectroscopy and magnetic susceptibility measurements. The proton conductivity of two selected compounds is also reported.

Copper phosphonatoethanesulfonates: temperature dependent in situ energy dispersive X-ray diffraction study and influence of the pH on the crystal structures.

The system Cu(2+)/H2O3P-C2H4-SO3H/NaOH was investigated using in situ energy dispersive X-ray diffraction (EDXRD) to study the formation and temperature induced phase transformation of previously described copper phosphonosulfonates. Thus, the formation of [Cu2(O3P-C2H4-SO3)(OH)(H2O)]·3H2O (4) at 90 °C is shown to proceed via a previously unknown intermediate [Cu2(O3P-C2H4-SO3)(OH)(H2O)]·4H2O (6), which could be structurally characterized from high resolution powder diffraction data. Increase of the reaction temperature to 150 °C led to a rapid phase transformation to [Cu2(O3P-C2H4-SO3)(OH)(H2O)]·H2O (1), which was also studied by in situ EDXRD. The comparison of the structures of 1, 4, and 6 allowed us to establish a possible reaction mechanism. In addition to the in situ crystallization studies, microwave assisted heating for the synthesis of the copper phosphonosulfonates was employed, which allowed the growth of larger crystals of [NaCu(O3P-C2H4-SO3)(H2O)2] (5) suitable for single crystal X-ray diffraction. Through the combination of force field calculations and Rietveld refinement we were able to determine the crystal structure of [Cu1.5(O3P-C2H4-SO3)] 2H2O (3) and thus structurally characterize all compounds known up to now in this well investigated system. With the additional structural data we are now able to describe the influence of the pH on the structure formation.

P03, the microfocus and nanofocus X-ray scattering (MiNaXS) beamline of the PETRA III storage ring: the microfocus endstation.

The P03 beamline, also called the microfocus and nanofocus X-ray scattering (MiNaXS) beamline, exploits the excellent photon beam properties of the low-emittance source PETRA III to provide a microfocused/nanofocused beam with ultra-high intensity for time-resolved X-ray scattering experiments. The beamline has been designed to perform X-ray scattering in both transmission and reflection geometries. The microfocus endstation started user operation in May 2011. An overview of the beamline status and of some representative results highlighting the performance of the microfocus endstation at MiNaXS are given.

Two- and Three-Dimensional Network of Nanoparticles via Polymer-Mediated Self-Assembly.

We show a route to produce a two- and three-dimensional network of nanoparticles via polymer-mediated self-assembly. A negatively charged polymer, CO2-functionalized poly (para-phenyleneethylene) (PPE-CO2), is used to build this network of iron-platinum (Fe-Pt) nanoparticles. The nanoparticles arrange locally in hexagonal and cubic lattice type network structures. The size and form of the networks are characterized with atomic force microscopy (AFM), transmission electron microscopy (TEM), small-angle X-ray scattering (SAXS), and grazing incidence small-angle X-ray scattering (GISAXS). In thin film the network is perturbed due to the force field acting during spin coating.

Time-resolved ultrathin cobalt film growth on a colloidal polymer template.

Cobalt (Co) sputter deposition onto a colloidal polymer template is investigated using grazing incidence small-angle X-ray scattering (GISAXS), scanning electron microscopy (SEM), and atomic force microscopy (AFM). SEM and AFM data picture the sample topography, GISAXS the surface and near-surface film structure. A two-phase model is proposed to describe the time evolution of the Co growth. The presence of the colloidal template results in the correlated deposition of an ultrathin Co film on the sample surface and thus in the creation of Co capped polystyrene (PS) colloids. Well below the percolation threshold, the radial growth is restricted and only height growth is observed.

Systematic and in situ energy dispersive X-ray diffraction investigations on the formation of lanthanide phosphonatobutanesulfonates: Ln(O(3)P-C(4)H(8)-SO(3))(H(2)O) (Ln = La-Gd).

Using the flexible linker H(2)O(3)P-C(4)H(8)-SO(3)H (H(3)L) and rare earth ions Ln(3+) (Ln = La, Ce, Pr, Nd, Sm, Eu, Gd) we were able to synthesize the new isostructural inorganic organic hybrid compounds Ln(O(3)P-C(4)H(8)-SO(3))(H(2)O). High-throughput experiments were employed to study the influence of the molar ratios Ln:H(3)L and pH on the product formation. The crystal structure of the compounds Sm(O(3)P-C(4)H(8)-SO(3))(H(2)O) (1) and Pr(O(3)P-C(4)H(8)-SO(3))(H(2)O) (2) were determined by single crystal diffraction. The structures are built up from chains of edge-sharing LnO(8)-polyhedra that are connected by the phosphonate and sulfonate groups into layers. These layers are linked by the -(CH(2))(4)- group to form a three-dimensional framework. The synthesis of compound 1 was scaled up in a conventional oven as well as in a microwave reactor system. A modification of a microwave reactor system allowed its integration into the beamline F3 at HASYLAB, DESY, Hamburg. The crystallization was investigated in situ by means of energy dispersive X-ray diffraction using conventional as well as microwave heating methods applying temperatures varying from 110 to 150 °C. The formation of Sm(O(3)P-C(4)H(8)-SO(3))(H(2)O) takes place in two steps. In the first step a crystalline intermediate was observed, which transforms completely into compound 1. The method by Sharp and Hancock was used to determine the rate constants, reaction exponents, and the Arrhenius activation energy for both reaction steps. Comparing both heating methods, microwave heating leads to fully crystallized reaction product after shorter reaction times, but neither the temperature nor the heating method has significant influence on the induction time.

Spatially resolved investigation of solution cast nanoparticle films by X-ray scattering and multidimensional data set classification.

A combinatorial high-throughput approach is used to investigate a solution cast gradient consisting of colloidal gold nanoparticles on top of a silicon substrate by means of a X-ray nanobeam. Classification algorithms are used to reveal and visualize structural transitions from a frozen colloidal solution to a well-defined nanostructure. Prominent length scales on the order of 100 nm are observed. A periodic change in the nanostructure along the gradient is explained by a simplified stick-slip model.