Gemcitabine Direct Electrochemical Detection from Pharmaceutical Formulations Using a Boron-Doped Diamond Electrode.

The development of fast and easy-to-use methods for gemcitabine detection is of great interest for pharmaceutical formulation control in both research laboratories and hospitals. In this study, we report a simple, fast and direct electrochemical method for gemcitabine detection using a boron-doped diamond electrode. The electrochemical oxidation of gemcitabine on a boron-doped diamond electrode was found to be irreversible in differential pulse voltammetry, and scan rate influence studies demonstrated that the process is diffusion-controlled. The influence of the pH and supporting electrolytes were also tested, and the optimized differential pulse voltammetry method was linear in the range of 2.5-50 µg/mL, with a detection limit of 0.85 µg/mL in phosphate-buffered saline (pH 7.4; 0.1 M). An amperometric method was also optimized for gemcitabine detection. The linear range of the method was 0.5-65 µg/mL in phosphate-buffered saline of pH 7.4 as well as pH 5.5, the limit of detection being 0.15 µg/mL. The optimized differential pulse voltammetry and amperometric detection strategies were successfully applied to pharmaceutical formulations, and the results were compared to those obtained by high-performance liquid chromatography and UV-Vis spectrophotometry with good correlations.

Hybrid Nanocomposite Platform, Based on Carbon Nanotubes and Poly(Methylene Blue) Redox Polymer Synthesized in Ethaline Deep Eutectic Solvent for Electrochemical Determination of 5-Aminosalicylic Acid.

A novel hybrid composite of conductive poly(methylene blue) (PMB) and carbon nanotubes (CNT) was prepared for the detection of 5-aminosalicylic acid (5-ASA). Electrosynthesis of PMB with glassy carbon electrode (GCE) or with carbon nanotube modified GCE was done in ethaline deep eutectic solvent of choline chloride mixed with ethylene glycol and a 10% v/v aqueous solution. Different sensor architectures were evaluated in a broad range of pH values in a Britton-Robinson (BR) buffer using electrochemical techniques, chronoamperometry (CA), and differential pulse voltammetry (DPV), to determine the optimum sensor configuration for 5-ASA sensing. Under optimal conditions, the best analytical performance was obtained with CNT/PMBDES/GCE in 0.04 M BR buffer pH 7.0 in the range 5-100 µM 5-ASA using the DPV method, with an excellent sensitivity of 9.84 µA cm-2 µM-1 (4.9 % RSD, n = 5) and a detection limit (LOD) (3σ/slope) of 7.7 nM, outclassing most similar sensors found in the literature. The sensitivity of the same sensor obtained in CA (1.33 µA cm-2 µM-1) under optimal conditions (pH 7.0, Eapp = +0.40 V) was lower than that obtained by DPV. Simultaneous detection of 5-ASA and its analogue, acetaminophen (APAP), was successfully realized, showing a catalytic effect towards the electro-oxidation of both analytes, lowering their oxidation overpotential, and enhancing the oxidation peak currents and peak-to-peak separation as compared with the unmodified electrode. The proposed method is simple, sensitive, easy to apply, and economical for routine analysis.

An Electrochemical Strategy for the Simultaneous Detection of Doxorubicin and Simvastatin for Their Potential Use in the Treatment of Cancer.

The aim of this study was to develop a disposable, simple, fast, and sensitive sensor for the simultaneous electrochemical detection of doxorubicin (DOX) and simvastatin (SMV), which could be used in preclinical studies for the development of new pharmaceutical formulations for drug delivery. Firstly, the electrochemical behavior of each molecule was analyzed regarding the influence of electrode material, electrolyte solution, and scan rate. After this, the proper electrode material, electrolyte solution, and scan rate for both active substances were chosen, and a linear sweep voltammetry procedure was optimized for simultaneous detection. Two chronoamperometry procedures were tested, one for the detection of DOX in the presence of SMV, and the other one for the detection of DOX and SMV together. Finally, calibration curves for DOX and SMV in the presence of each other were obtained using both electrochemical methods and the results were compared. The use of amperometry allowed for a better limit of detection (DOX: 0.1 µg/mL; SMV: 0.7 µg/mL) than the one obtained in voltammetry (1.5 µg/mL for both drugs). The limits of quantification using amperometry were 0.5 µg/mL for DOX (dynamic range: 0.5-65 µg/mL) and 2 µg/mL for SMV (dynamic range: 2-65 µg/mL), while using voltammetry 1 µg/mL was obtained for DOX (dynamic range: 1-100 µg/mL) and 5 µg/mL for SMV (dynamic range: 5-100 µg/mL). This detection strategy represents a promising tool for the analysis of new pharmaceutical formulations for targeted drug delivery containing both drugs, whose association was proven to bring benefits in the treatment of cancer.

Selective Detection of Folic Acid Using 3D Polymeric Structures of 3-Carboxylic Polypyrrole.

The detection of folic acid in biological samples or pharmaceutical products is of great importance due to its implications in the biological functions of the human body, along with the development and growth of the fetus. The deficiency of folic acid can be reversed by the intake of different pharmaceutical formulations or alimentary products fortified with this molecule. The elaboration of sensing platforms represents a continuous work in progress, a task in which the use of conductive polymers modified with different functionalities represents one of the outcoming strategies. The possibility of manipulating their morphology with the use of templates or surfactants represents another advantage. A sensing platform based on carboxylic functionalized polypyrrole was synthesized via the electrochemical approach in the presence of a polymeric surfactant on a graphite-based surface. The sensor was able to detect the folic acid from 2.5 µM to 200 µM with a calculated limited of detection of 0.8 µM. It was employed for the detection of the analyte from commercial human serum and pharmaceutical products with excellent recovery rates. The results were double checked using an optimized spectrophotometric procedure that confirmed furthermore the performances of the sensor related to real samples assessment.

Correlated quantification using microbiological and electrochemical assays for roxithromycin determination in biological and pharmaceutical samples.

Microbiological and electrochemical assays, applying the cylinder-plate and differential pulse voltammetry as techniques, are reported for the quantitative determination of roxithromycin in serum and solid pharmaceutical form. The microbiological assay is based upon the inhibitory effect of this drug on the strain Bacillus subtilis ATCC 9372 used as the test microorganism. Linearity of the calibration curve was observed over the concentration range of 8.37-83.70 µg mL-1, with relative standard deviation values less than 5.0%. The electrochemical behavior of roxithromycin was studied at a graphite screen-printed electrode modified with graphene by using cyclic voltammetry and differential pulse voltammetry. The current value of the oxidative peak obtained for roxithromycin at 0.65 V vs. Ag/AgCl in 0.03 mol L-1 phosphate buffer solution (pH 7.0) with a scan rate of 0.1 V-1 is a linear function of the concentration in a range of 4.19-83.70 µg mL-1 (5-100 µmol L-1). A comparative study was carried out and both methods were applied for the determination of roxithromycin in solid dosage forms and spiked serum. The bioassay results of human serum samples were in accordance with the electrochemical ones (R2 = 0.988, P < 0.001), and the Bland-Altman method also showed good agreement between the values obtained by both procedures. Moreover, the statistical comparison indicated that there was no significant difference between the proposed techniques regarding both accuracy and precision.

Colorimetric multienzymatic smart sensors for hydrogen peroxide, glucose and catechol screening analysis.

In this work, we present a smartphone-based multiplexed enzymatic biosensor utilizing the unique colorimetric properties of the poly(aniline-co-anthranilic acid) (ANI-co-AA) composite film coupled with horseradish peroxidase (HRP), glucose oxidase (GOx), horseradish peroxidase-glucose oxidase (GOx-HRP) and tyrosinase (Tyr) enzymes. The enzymes are immobilized on the composite polymer film by adsorption and they catalyze a reversible redox color change of the host polymer from green to blue in the presence of their substrate. A smartphone was applied as color detector, for image acquisition and data handling. A ColorLab® android application, free of charge software application, was used to enable easy and clear display of the sensors' response indicating remarkable changes in the optical features. The results were confirmed by the spectrophotometric measurements. The developed colorimetric enzymatic biosensors were studied and optimized in relation to different experimental parameters. Moreover, the colorimetric enzymatic biosensors were applied to food and pharmaceutical analysis. It has been shown by these studies that the colorimetric biosensors are promising as quick and simple tests for handheld analysis in various fields.

Saliva, a Magic Biofluid Available for Multilevel Assessment and a Mirror of General Health-A Systematic Review.

BACKGROUND: Saliva has been recently proposed as an alternative to classic biofluid analyses due to both availability and reliability regarding the evaluation of various biomarkers. Biosensors have been designed for the assessment of a wide spectrum of compounds, aiding in the screening, diagnosis, and monitoring of pathologies and treatment efficiency. This literature review aims to present the development in the biosensors research and their utility using salivary assessment. METHODS: a comprehensive literature search has been conducted in the PubMed database, using the keywords "saliva" and "sensor". A two-step paper selection algorithm was devised and applied. RESULTS: The 49 papers selected for the present review focused on assessing the salivary biomarkers used in general diseases, oral pathologies, and pharmacology. The biosensors proved to be reliable tools for measuring the salivary levels of biochemical metabolic compounds such as glucose, proteinases and proteins, heavy metals and various chemical compounds, microorganisms, oncology markers, drugs, and neurotransmitters. CONCLUSIONS: Saliva is a biofluid with a significant clinical applicability for the evaluation and monitoring of a patient's general health. Biosensors designed for assessing a wide range of salivary biomarkers are emerging as promising diagnostic or screening tools for improving the patients' quality of life.

Enzyme-Graphene Platforms for Electrochemical Biosensor Design With Biomedical Applications.

Due to the growing need for sensitive, reliable, reusable, fast, and cheap devices for the detection of analytes which have an important role in diagnosis of different diseases, in metabolic disorders, in monitoring treatment of serious diseases such as cancers, the sensing field has attracted huge interest from the scientists. The majority of the traditional methods that are currently in use are invasive, expensive, and laborious. Moreover, highly specialized operators and sophisticated instrumentations are usually required. Taking these into account, the introduction of electrochemical sensors and biosensors avoid a lot of the disadvantages associated with most of the used analytical techniques. The biggest contribution to this development was the use of different nanomaterials as transducers of the analytical signal. The properties, such as high mechanical strength, good electrical conductivity, and ability to serve as efficient signal transducers, make carbon-based nanomaterials, including graphene, ideal materials for biosensor applications. Furthermore, graphene presents high surface area that can be easily modified in different ways to be adapted for the immobilization of various biocompounds for the construction of biosensors. Recent advances regarding the use of graphene and graphene materials for the immobilization of several enzymes for biosensor development and their applications for the detection of chemical and biological species are presented with focus on different enzymes immobilization techniques. In the end, the future trends for the development of graphene-based biosensors in biomedical field are also discussed.

Chemical Sensing at the Robot Fingertips: Toward Automated Taste Discrimination in Food Samples.

The development of robotic sensors that mimic the human sensing capabilities is critical for the interaction and cognitive abilities of modern robots. Though robotic skin with embedded pressure or temperature sensors has received recent attention, robotic chemical sensors have long been unnoticed due to the challenges associated with realizing chemical sensing modalities on robotic platforms. For realizing such chemically sensitive robotic skin, we exploit here the recent advances in wearable chemical sensor technology and flexible electronics, and describe chemical sensing robotic fingers for rapid screening of food flavors and additives. The stretchable taste-sensing finger electrochemical devices are printed on the robotic glove, which simulates the soft skin, and are integrated with a wireless electronic board for real-time data transmission. The printed middle, index, and ring robotic fingers allow accurate discrimination between sweetness, sourness, and spiciness, via direct electrochemical detection of glucose, ascorbic acid, and capsaicin. The sweet-sensing ability has been coupled with a caffeine-sensing robotic finger for rapid screening of the presence of sugar and caffeine in common beverages. The "sense of taste" chemically sensitive robotic technology thus enables accurate discrimination between different flavors, as was illustrated in numerous tests involving a wide range of liquid and solid food samples. Such realization of advanced wearable taste-sensing systems at the robot fingertips should pave the way to automated chemical sensing machinery, facilitating robotic decision for practical food assistance applications, with broad implications to a wide range of robotic sensing applications.

Finger-Based Printed Sensors Integrated on a Glove for On-Site Screening Of Pseudomonas aeruginosa Virulence Factors.

Early screening of clinically relevant pathogens in the environment is a highly desirable goal in clinical care, providing precious information that will improve patient-care outcomes. In this work, a glove-based electrochemical sensor has been designed for point-of-use screening of Pseudomonas aeruginosa's virulence factors. The methodology used for the elaboration of the fabric platform relied on printing the conductive inks on the index and middle fingers of the glove, with the goal of screening pyocyanin and pyoverdine targets. The analytical signatures of the analytes were recorded in about 4 min, via the rapid and selective square-wave-voltammetry technique. Finger-based sensors display good performance and discrimination between the targets and potential interferences, along with good reproducibility. The sensors featured linearity over the 0.01-0.1 µM range for pyocyanin and 5-50 µM range for pyoverdine, with sensitivities of 2.51 µA/µM for pyocyanin and 1.09 nA/µM for pyoverdine ( R2 = 0.990 and 0.995, respectively) and detection limits of 3.33 nM for pyocyanin and 1.66 µM for pyoverdine. Moreover, the sensors were tested in binary mixtures of analytes, with successful outcomes. In order to gain information from the surrounding environment, the active electronic areas of the printed fingers were coated with a conductive hydrogel matrix, and relevant target surfaces were "swiped for notification" of contaminants. The simple fabrication, low-cost, and reusability of the proposed glove are likely to underpin the progressive drive of wearable sensors toward decentralized environmental and healthcare applications.

DNA-Based Sensor for the Detection of an Organophosphorus Pesticide: Profenofos.

In this work, we propose an electrochemical DNA aptasensor for the detection of profenofos, an organophosphorus pesticide, based on a competitive format and disposable graphite screen-printed electrodes (GSPEs). A thiol-tethered DNA capture probe, which results to be complementary to the chosen aptamer sequence, was immobilised on gold nanoparticles/polyaniline composite film-modified electrodes (AuNPs/PANI/GSPE). Different profenofos solutions containing a fixed amount of the biotinylated DNA aptamer were dropped onto the realized aptasensors. The hybridisation reaction was measured using a streptavidin-alkaline phosphatase enzyme conjugate, which catalyses the hydrolysis of 1-naphthyl -phosphate. The 1-naphtol enzymatic product was detected by means of differential pulse voltammetry (DPV). The aptasensor showed itself to work as a signal off sensor, according to the competitive format used. A dose response curve was obtained between 0.10 μM and 10 μM with a detection limit of 0.27 μM.

Wearable Wireless Tyrosinase Bandage and Microneedle Sensors: Toward Melanoma Screening.

Wearable bendable bandage-based sensor and a minimally invasive microneedle biosensor are described toward rapid screening of skin melanoma. These wearable electrochemical sensors are capable of detecting the presence of the tyrosinase (TYR) enzyme cancer biomarker in the presence of its catechol substrate, immobilized on the transducer surface. In the presence of the surface TYR biomarker, the immobilized catechol is rapidly converted to benzoquinone that is detected amperometrically, with a current signal proportional to the TYR level. The flexible epidermal bandage sensor relies on printing stress-enduring inks which display good resiliency against mechanical deformations, whereas the hollow microneedle device is filled with catechol-coated carbon paste for assessing tissue TYR levels. The bandage sensor can thus be used directly on the skin whereas microneedle device can reach melanoma tissues under the skin. Both wearable sensors are interfaced to an ultralight flexible electronic board, which transmits data wirelessly to a mobile device. The analytical performance of the resulting bandage and microneedle sensing systems are evaluated using TYR-containing agarose phantom gel and porcine skin. The new integrated conformal portable sensing platforms hold considerable promise for decentralized melanoma screening, and can be extended to the screening of other key biomarkers in skin moles.

Fully edible biofuel cells.

The first example of a fully edible biofuel cell (BFC), based solely on highly biocompatible food materials without any additional external mediators, is described. The new BFC energy-harvesting approach relies on a variety of edible plant/mushroom extract/vegetable oil/charcoal paste biocatalytic electrodes and represents an attractive route for energy harvesting towards ingestible biomedical devices. The edible BFC anode and cathode paste materials consist of biocatalytic rich mushroom, apple, plum and banana plant tissues, along with dietary activated charcoal and water-immiscible olive oil, corn oil, and sesame oil for creating the paste matrix. The ethanol/O2 BFC relies on a bioanode, based on ethanol oxidation induced by the intrinsic biocatalytic activity of its mushroom component, along with a biocathode based on oxygen-reducing apple extract containing polyphenol-oxidase and phenolic compounds. The integrated natural catalytic system and selective biocatalytic activity of the natural extracts offer successful operation of BFCs without any extra mediators or membrane separating the anode and the cathode. The mushroom/apple/olive oil-based BFC displays a favorable power density of 282 µW cm-2 with an open circuit voltage (OCV) of 0.24 V. The power and OCV signals are linearly proportional to ethanol levels and indicate promise for self-powered alcohol sensing. The food-based BFCs were reproducible and able to maintain a power performance of over 80% of their initial output for four hours. These edible energy-harvesting BFCs hold great promise for the next-generation of ingestible devices and smart self-powered biosensors for monitoring health and the digestive system.

Molecular-trapping in Emulsion's Monolayer: A New Strategy for Production and Purification of Bioactive Saponins.

Saponins from defatted root-extract of Securidaca longipedunculata were systematically entrapped in emulsion monolayer-barrier and finally recovered in pure form through demulsification. First, their molecules were dispersed in water to engineer a monomolecular film architecture, via self-assembly. Emulsifying with ethyl-ether resulted in swollen micelles and engendered phase-inversion and phase-separation, by disrupting the thermodynamic equilibrium. As positive outcome, a Winsor II system was obtained, having saponin-rich upper phase (ethyl-ether) and impurities bound lower phase (aqueous). Saponin particles underwent transition in insoluble ethyl-ether, precipitated and recovered as solids. The entire process was bioactivity-guided and validated using pooled fractions of securidaca saponins, purified by TLC (RP-C18, F254S). TEM and SEM revealed interesting morphologies and particle sizes between nanometer and micron. At the end, purity output of 90% and total recovery of 94% were achieved. Here we show that "molecular-trapping in emulsion's monolayer" is an effective method for recovery, production and purification of saponins of plant origin.

Electrochemical determination of cephalosporins using a bare boron-doped diamond electrode.

The electrochemical oxidation of seven cephalosporins (ceftriaxone, cefotaxime, ceftazidime, cefadroxil, cefuroxime, cefaclor, cefalexin) was evaluated at high potential, using a bare boron-doped diamond electrode and the influence on the analytical response of the side chains was investigated. Based on the anodic oxidation of the cephalosporin nucleus, a simple and sensitive method was developed for the electrochemical detection of cefalexin by differential pulse voltammetry. After the optimization of the experimental conditions, a linear correlation was obtained between the peak height and the molar concentration of cefalexin in the range of 0.5 µM-700 µM, with a limit of detection of 34.74 ng mL-1. The anodic peak for cefalexin was evaluated in the presence of other cephalosporin molecules and of other common interferents. The developed method was applied to detection of cefalexin from real environmental, biomedical and pharmaceutical samples, with good results. The electrochemical oxidation of cephalosporins was successfully adapted for flow injection analyses, with sensitive and reproducible successive analyses of cefalexin, in different concentrations. The flow analyses allowed also the determination of the total amount of cephalosporins found in the sample.

Smartphone-based immunosensor for CA125 detection.

In this work, we report the design, the development and the characterization of the analytical performances of a colorimetric smartphone-based immunosensor for the detection of cancer antigen 125 (CA125). The immunosensor was based on a sandwich strategy in which the primary antibody was immobilized by spotting onto the 3D nitrocellulose membrane. The immunospots were subsequently incubated with CA125 solutions, followed by the affinity reaction with a secondary antibody labeled with gold nanoparticles (AuNPs). The antibody-AuNPs captured onto immunospots induced the silver deposition from a silver enhancer solution leading to the formation of gold-silver nanoparticles of different grey color spots depending on CA125 concentration. The 8 megapixels smartphone camera was integrated in a home-made dark box and used as transducer of color image acquisition and data handling. The pixel intensity of the captured images was determined by an image processing algorithm. The experimental parameters involved in each step of the immunosensor design were studied and optimized, obtaining a limit of detection of 30U/mL CA125. The selectivity of the immunoassay was proven against different concentration solutions of Vascular Endothelial Growth Factor (VEGF) antigen as an unspecific protein when a blank signal was obtained for all tested solutions. Finally, preliminary experiments in human serum samples spiked with CA125 protein were also performed. Therefore, the proposed system could represent a powerful point-of-care tool for the next generation technology for detecting and monitoring cancer biomarkers at early stages by taking advantage of nowadays gadgets with enhanced features such as smartphones.

Detection of Dopamine by a Biomimetic Electrochemical Sensor Based on Polythioaniline-Bridged Gold Nanoparticles.

A new biomimetic electrochemical sensor was developed for the detection of dopamine based on a glassy carbon electrode modified with electrochemically generated gold nanoparticles. The preparation of the polymer is simple and cost-effective, achieving the polymerization of thioaniline and generation of gold nanoparticles in a single step by cyclic voltammetry, in the presence of the target molecule, dopamine. After extraction, the imprinted polymer exhibits high sensitivity and selectivity for dopamine. Moreover, the developed imprinted polymer film allows the fast, direct detection of dopamine without the need of a redox mediator. The formation of a self-assembled monolayer of the monomer prior to electropolymerization ensures the adherence of the film onto the electrode surface, conferring good stability to the sensor (over two weeks). Cyclic voltammetry, electrochemical impedance spectroscopy, atomic force microscopy, scanning electron microscopy, and energy dispersive X-ray spectroscopy were used for the complete characterization of the developed sensor, and differential pulse voltammetry was used for its testing.

Double gene siRNA knockdown of mutant p53 and TNF induces apoptosis in triple-negative breast cancer cells.

Apoptosis is the major downregulated pathway in cancer. Simultaneous inhibition using specific small interfering RNA (siRNA) of two key player genes, p53 and TNF, is an interesting and feasible strategy when it comes to investigating various molecular pathways and biological processes in triple-negative breast cancer (TNBC), which is one of the most aggressive and therapeutically unresponsive forms of breast cancers. Our present research focuses on evaluating the impact of double p53-siRNA and TNF-siRNA knockdown at a cellular level, and also evaluating cell proliferation, apoptosis, induction of autophagy, and gene expression by using reverse transcription polymerase chain reaction array approaches. Simultaneous inhibition of p53 and TNF in Hs578T TNBC human cell line revealed a panel of up- and downregulated genes involved in apoptosis. Furthermore, the effects of double gene knockdown were validated in a second TNBC cell line, MDA-MB-231, by using reverse transcription polymerase chain reaction TaqMan assay. All our findings help in understanding the functional mechanisms of extrinsic apoptosis, cell signaling pathways, and the mechanisms involved in tumor cell survival, growth, and death in TNBC.

MicroRNAs as regulators of apoptosis mechanisms in cancer.

MicroRNAs or miRNAs are small non-coding RNAs that regulate gene expression. Their discovery has brought new knowledge in biological processes of cancer. Involvement of miRNAs in cancer development includes several major pathways from cell transformation to tumor cell development, metastasis and resistance to treatment. The first part of this review discusses miRNAs function in the intrinsic and extrinsic pathways of apoptosis. Due to the fact that many miRNAs that regulate apoptosis have been shown to play a major role in tumor cell resistance to treatment, in the second part of the review we aim at discussing miRNAs potential in becoming curative molecules.

First Occurrence of Tetrazines in Aqueous Solution: Electrochemistry and Fluorescence.

The photophysical and electrochemical properties of tetrazines substituted by linear 2,3-naphtalimide antennas and/or adamantane groups specifically dedicated to host-guest interactions with cyclodextrins are studied both in organic and aqueous media. In acetonitrile solvent, the reduction potential of tetrazine leading to the anion radical is shifted, depending on the electron-withdrawing power of the substituent of the tetrazines. Due to the hydrophobic character of these compounds, their solubilization in aqueous solution is achieved successively in presence of either ß-cyclodextrins or gold nanoparticules modified by ß-cyclodextrins. We demonstrate that the formation of the inclusion compound tetrazine-cyclodextrin allows the solubilization of the tetrazines in aqueous solution. The supramolecular assemblies obtained in water retain tetrazine's emission properties, yielding a yellow fluorescence.