A dual-functional ultraviolet (UV) photodetector with a large UV-to-visible rejection ratio is presented, in which interdigitated finger-type two-dimensional graphene electrodes are introduced to an AlGaN/GaN heterostructure. Two photocurrent generation mechanisms of photovoltaic and photoconductive dominances coexist in the device. The dominance of the mechanisms changes with the induced bias voltage. Below a threshold voltage, the device showed fairly low responsivities but fast response times, as well as a constant photocurrent against the induced bias. However, the opposite characteristics appeared with high bias voltage. Specifically, above the threshold voltage, the device showed high responsivities with additional gain, but slow rise and recovery times. For instance, the responsivity of 10.9 A/W was observed with the gain of 760 at the induced bias voltage of 5 V. This unique multifunctionality enabled by the combination of an AlGaN/GaN heterostructure with graphene electrodes facilitates the development of a single device that can achieve multiple purposes of photodetection.
Nitride-based ultraviolet light-emitting diodes (UV LEDs) are promising replacements for conventional UV lamps. However, the external quantum efficiency of UV LEDs is much lower than for visible LEDs due to light absorption in the p-GaN contact and electrode layers, along with p-AlGaN growth and doping issues. To minimize such absorption, we should obtain direct ohmic contact to p-AlGaN using UV-transparent ohmic electrodes and not use p-GaN as a contact layer. Here, we propose a glass-based transparent conductive electrode (TCE) produced using electrical breakdown (EBD) of an AlN thin film, and we apply the thin film to four (Al)GaN-based visible and UV LEDs with thin buffer layers for current spreading and damage protection. Compared to LEDs with optimal ITO contacts, our LEDs with AlN TCEs exhibit a lower forward voltage, higher light output power, and brighter light emission for all samples. The ohmic transport mechanism for current injection and spreading from the metal electrode to p-(Al)GaN layer via AlN TCE is also investigated by analyzing the p-(Al)GaN surface before and after EBD.
While there is an urgent need for semiconductor-based efficient deep ultraviolet (DUV) sources, the efficiency of AlGaN DUV light-emitting diodes (LEDs) remains very low because the extraction of DUV photons is significantly limited by intrinsic material properties of AlGaN. Here, we present an elegant approach based on a DUV LED having multiple mesa stripes whose inclined sidewalls are covered by a MgF2/Al omni-directional mirror to take advantage of the strongly anisotropic transverse-magnetic polarized emission pattern of AlGaN quantum wells. The sidewall-emission-enhanced DUV LED breaks through the fundamental limitations caused by the intrinsic properties of AlGaN, thus shows a remarkable improvement in light extraction as well as operating voltage. Furthermore, an analytic model is developed to understand and precisely estimate the extraction of DUV photons from AlGaN DUV LEDs, and hence to provide promising routes for maximizing the power conversion efficiency.
The efficiency of an AlGaN deep-ultraviolet light-emitting diode with peak emission wavelength of 285 nm is investigated as a function of current over a wide range of temperatures (110 K to 300 K). We find that the efficiency-versus-current curve exhibits unique and distinct features over the entire temperature range including three points of inflection. At low temperatures, the change in slope in the efficiency-versus-current curve is particularly pronounced producing a minimum in the efficiency after which the efficiency rises again. Furthermore, at high current density, the low-temperature efficiency exceeds the room-temperature efficiency. The feature-rich efficiency-versus-current curve is consistent with an enhancement in p-type conductivity by field-ionization of acceptors that occurs in the high-injection regime and is particularly pronounced at low temperatures. Differential conductivity measurements show a marked rise in the high-injection regime that is well correlated to the minimum point in the efficiency-versus-current curve.
Photo-electrodes with tailored three-dimensional nanostructures offer a large enhancement in light harvesting capability for various optoelectronic devices enabled by strong light scattering in the nanostructures as well as improved charge transport. Here we present an array of three-dimensional titanium dioxide (TiO2) nanohelixes fabricated by the oblique angle deposition method as a multifunctional photoanode for CdSe quantum dot sensitized solar cells (QDSSCs). The CdSe QDSSC with a TiO2 nanohelix photoanode shows a 100% higher power conversion efficiency despite less light being absorbed in CdSe QDs when compared with a conventional TiO2 nanoparticle photoanode. We attribute the higher power conversion efficiency to strong light scattering by the TiO2 nanohelixes and much enhanced transport and collection of photo-generated carriers enabled by the unique geometry and near-single crystallinity of the TiO2 nanohelix structure.
The performance enhancement of polycrystalline Si solar cells by using an optimized discrete multilayer anti-reflection (AR) coating with broadband and omni-directional characteristics is presented. Discrete multilayer AR coatings are optimized by a genetic algorithm, and experimentally demonstrated by refractive-index tunable SiO2 nano-helix arrays and co-sputtered (SiO2)x(TiO2)1âx thin film layers. The optimized multilayer AR coating shows a reduced total reflection, leading to the high incident-photon-to-electron conversion efficiency over a correspondingly wide range of wavelengths and incident angles, offering a very promising way to harvest more solar energy by virtually any type of solar cells for a longer time of a day.
Nanostructures/chemistry , Nanotechnology/methods , Refractometry/instrumentation , Scattering, Radiation , Silicon Dioxide/chemistry , Solar Energy , Sunlight , Materials Testing , Optics and Photonics , Surface Properties
Nanoporous coatings have become the subject of intense investigation, in part because they have been shown to have unique and tailorable physical properties that can depart greatly from their dense or macroscopic counterparts. Nanoporous coatings are frequently fabricated utilizing oblique-angle or glancing-angle physical vapor-phase deposition techniques. However, a significant limitation for such coatings exists; they are almost always deposited on smooth and rigid planar substrates, such as silicon and glass. This limitation greatly constrains the applicability, tailorability, functionality and even the economic viability, of such nanoporous coatings. Here, we report our findings on nanoporous/polymer composite systems (NPCS) fabricated by utilizing oblique-angle electron-beam methodology. These unique composite systems exhibit several favorable characteristics, namely, (i) fine-tuned control over coating nanoporosity and thickness, (ii) excellent adhesion between the nanoporous coating and polymer substrate, (iii) the ability to withstand significant and repeated bending, and (iv) the ability to be molded conformably on two and three-dimensional surfaces while closely retaining the composite system's designed nanoporous film structure and, hence, properties.
Crystallization/methods , Nanostructures/chemistry , Nanostructures/ultrastructure , Polymers/chemistry , Adhesiveness , Adsorption , Elastic Modulus , Macromolecular Substances/chemistry , Materials Testing , Molecular Conformation , Particle Size , Porosity , Surface Properties
Oblique-angle deposition of indium tin oxide (ITO) is used to fabricate optical thin-film coatings with a porous, columnar nanostructure. Indium tin oxide is a material that is widely used in industrial applications because it is both optically transparent and electrically conductive. The ITO coatings are fabricated, using electron-beam evaporation, with a range of deposition angles between 0 degrees (normal incidence) and 80 degrees. As the deposition angle increases, we find that the porosity of the ITO film increases and the refractive index decreases. We measure the resistivity of the ITO film at each deposition angle, and find that as the porosity increases, the resistivity increases superlinearly. A new theoretical model is presented to describe the relationship between the ITO film's resistivity and its porosity. The model takes into account the columnar structure of the film, and agrees very well with the experimental data.
We investigate the effects of the refractive index of the encapsulant on the light-extraction efficiency (LEE) of light-emitting diodes (LEDs) for GaN LEDs (n ≈ 2.5) and AlGaInP LEDs (n ≈ 3.0). For non-absorbing rectangular parallelepiped LED chips, as the refractive index of the encapsulant increases, the LEE first increases quasi-linearly, then increases sub-linearly, and finally a saturation is reached. Furthermore, LEDs with a dual-layer graded-refractive-index (GRIN) encapsulant (n(encapsulant 1) = 1.57 and n(encapsulant 2) = 1.41) is fabricated through a two-step curing process. We demonstrate that such an LED further enhances the LEE by reducing Fresnel reflection loss at the encapsulant/air interface by 35% compared with an LED encapsulated with a single-layer encapsulant (n(encapsulant) = 1.57).
Optical interference filters utilizing tunable refractive index layers are shown to have higher spectral fidelity as compared to conventional filters consisting of non-tunable refractive index layers. To demonstrate this increase in spectral fidelity, we design and compare a variety of optical interference filters employing both tunable and non-tunable refractive index layers. Additionally, a five-layer optical interference filter utilizing tunable refractive index layers is designed and fabricated for use with a Xenon lamp to replicate the Air Mass 0 solar irradiance spectrum and is shown to have excellent spectral fidelity.
Conventional white-light sources suffer from a fundamental trade-off between color rendering index and the luminous efficacy; increasing one generally comes at the expense of the other. We demonstrate through simulation that dual-wavelength blue-emitting active regions in phosphor-converted white light sources maximize the output luminous flux while significantly increasing the color rendering ability. Our results indicate that such improvements can be achieved over a broad range of correlated color temperatures.
Optics and Photonics , Color , Computer Simulation , Equipment Design , Light , Lighting/methods , Models, Statistical , Phosphorus/chemistry , Temperature
The field of photonics starts with the efficient generation of light. The generation of efficient yet highly controllable light can indeed be accomplished with light-emitting diodes (LEDs), which are, in principle, capable of generating white light with a 20 times greater efficiency than conventional light bulbs. Deployed on a global scale to replace conventional sources, such solid-state light sources will result in enormous benefits that, over a period of 10 years, include (1) gigantic energy savings of 1.9 x 1020 joule, (2) a very substantial reduction in global-warming CO2 emissions, (3) a strong reduction in the emission of pollutants such as acid-rain-causing SO2, mercury (Hg), and uranium (U), and (4) financial savings exceeding a trillion (10(12)) US$. These benefits can be accomplished by the "replacement paradigm" in which conventional light sources are replaced by more energy efficient, more durable, and non-toxic light sources. However, it will be shown that solid-state light sources can go beyond the replacement paradigm, by providing new capabilities including the control of spectrum, color temperature, polarization, temporal modulation, and spatial emission pattern. We will show that such future, "smart" light sources, can harness the huge potential of LEDs by offering multi-dimensional controllability that will enhance the functionality and performance of light sources in a wide range of applications. These applications include optical microscopy, imaging, display technologies, communications, networking, and transportation systems.
To harness the full spectrum of solar energy, Fresnel reflection at the surface of a solar cell must be eliminated over the entire solar spectrum and at all angles. Here, we show that a multilayer nanostructure having a graded-index profile, as predicted by theory [J. Opt. Soc. Am. 66, 515 (1976); Appl. Opt. 46, 6533 (2007)], can accomplish a near-perfect transmission of all-color of sunlight. An ultralow total reflectance of 1%-6% has been achieved over a broad spectrum, lambda = 400 to 1600 nm, and a wide range of angles of incidence, theta = 0 degrees-60 degrees . The measured angle- and wavelength-averaged total reflectance of 3.79% is the smallest ever reported in the literature, to our knowledge.
Designs of multilayer antireflection coatings made from co-sputtered and low-refractive-index materials are optimized using a genetic algorithm. Co-sputtered and low-refractive-index materials allow the fine-tuning of refractive index, which is required to achieve optimum anti-reflection characteristics. The algorithm minimizes reflection over a wide range of wavelengths and incident angles, and includes material dispersion. Designs of antireflection coatings for silicon-based image sensors and solar cells, as well as triple-junction GaInP/GaAs/Ge solar cells are presented, and are shown to have significant performance advantages over conventional coatings. Nano-porous low-refractive-index layers are found to comprise generally half of the layers in an optimized antireflection coating, which underscores the importance of nano-porous layers for high-performance broadband and omnidirectional antireflection coatings.
Algorithms , Computer-Aided Design , Models, Theoretical , Optics and Photonics/instrumentation , Refractometry/instrumentation , Refractometry/methods , Computer Simulation , Equipment Design , Equipment Failure Analysis , Materials Testing , Models, Genetic
A non-rotationally symmetric encapsulation shape - which takes advantage of the low reflection coefficient for transverse magnetic polarized light near Brewster's angle - designed to enhance extraction of a particular desired linear polarization from an unpolarized source is reported. The algorithm for optimization of the shape is described. Numerical ray-tracing simulations of the encapsulation shape are performed and predict an integrated enhancement of 8.3% in the ratio of desired polarization to undesired polarization when the refractive index of the encapsulant is 1.5. Experimental measurements of fabricated encapsulant shapes agree well with numerical predictions.
A polarization-enhancing reflector design, which is matched to the emission characteristics of GaInN/GaN 460 nm light-emitting diodes grown on (0001) oriented sapphire substrates, is reported. Side-emitted light from these devices is known to be highly polarized with the electric field in the plane of the active region. Through selective rotation of polarization by the reflector, the in-plane polarized side-emitted light is directed upwards with a single dominant linear polarization. Polarization ratios as high as 3.5:1 are measured in the farfield, and the average polarization ratio is 1.9:1. If only light that strikes the reflector is considered, the polarization ratio is 2.5:1. The concept of the polarization-enhancing reflector and the numerical algorithm used to generate the optimized shape are also described.
More than a century after the introduction of incandescent lighting and half a century after the introduction of fluorescent lighting, solid-state light sources are revolutionizing an increasing number of applications. Whereas the efficiency of conventional incandescent and fluorescent lights is limited by fundamental factors that cannot be overcome, the efficiency of solid-state sources is limited only by human creativity and imagination. The high efficiency of solid-state sources already provides energy savings and environmental benefits in a number of applications. However, solid-state sources also offer controllability of their spectral power distribution, spatial distribution, color temperature, temporal modulation, and polarization properties. Such "smart" light sources can adjust to specific environments and requirements, a property that could result in tremendous benefits in lighting, automobiles, transportation, communication, imaging, agriculture, and medicine.
