RESUMEN
Because of its considerable theoretical specific capacity and energy density, lithium-sulfur battery technology holds great potential to replace lithium-ion battery technology. However, a versatile, low-cost, and easily scalable bulk synthesis method is essential for translating bench-level development to large-scale production. This paper reports the design and synthesis of a new scalable sulfur cathode, S@CNT/PANI/PPyNT/TiO2 (BTX). The rationally chosen cathode components suppress the migration of polysulfide intermediates via chemical interactions, enhance redox kinetics, and provide electrical conductivity to sulfur, rendering outstanding long-term cycling performance and strong initial specific capacity in terms of electrochemical performance. This cathode's cell demonstrated an initial specific capacity of 740 mA h g-1 at 0.2 C (with a capacity decay rate of 0.08% per cycle after 450 cycles).
RESUMEN
The rising demand for high-performance lithium-ion batteries, pivotal to electric transportation, hinges on key materials like the Ni-rich layered oxide LiNixCoyAlzO2 (NCA) used in cathodes. The present study investigates the redox mechanisms, with particular focus on the role of oxygen in commercial NCA electrodes, both fresh and aged under various conditions (aged cells have performed >900 cycles until a cathode capacity retention of â¼80%). Our findings reveal that oxygen participates in charge compensation during NCA delithiation, both through changes in transition metal (TM)-O bond hybridization and formation of partially reversible O2, the latter occurs already below 3.8 V vs. Li/Li+. Aged NCA material undergoes more significant changes in TM-O bond hybridization when cycling above 50% SoC, while reversible O2 formation is maintained. Nickel is found to be redox active throughout the entire delithiation and shows a more classical oxidation state change during cycling with smaller changes in the Ni-O hybridization. By contrast, Co redox activity relies on a stronger change in Co-O hybridization, with only smaller Co oxidation state changes. The Ni-O bond displays an almost twice as large change in its bond length on cycling as the Co-O bond. The Ni-O6 octahedra are similar in size to the Co-O6 octahedra in the delithiated state, but are larger in the lithiated state, a size difference that increases with battery ageing. These contrasting redox activities are reflected directly in structural changes. The NCA material exhibits the formation of nanopores upon ageing, and a possible connection to oxygen redox activity is discussed. The difference in interaction of Ni and Co with oxygen provides a key understanding of the mechanism and the electrochemical instability of Ni-rich layered transition metal oxide electrodes. Our research specifically highlights the significance of the role of oxygen in the electrochemical performance of electric-vehicle-grade NCA electrodes, offering important insights for the creation of next-generation long-lived lithium-ion batteries.
RESUMEN
Wadsley-Roth niobium oxide phases have attracted extensive research interest recently as promising battery anodes. We have synthesized the niobium-molybdenum oxide shear phase (Nb, Mo)13 O33 with superior electrochemical Li-ion storage performance, including an ultralong cycling lifespan of at least 15000â cycles. During electrochemical cycling, a reversible single-phase solid-solution reaction with lithiated intermediate solid solutions is demonstrated using in situ X-ray diffraction, with the valence and short-range structural changes of the electrode probed by in situ Nb and Mo K-edge X-ray absorption spectroscopy. This work reveals that the superior stability of niobium molybdenum oxides is underpinned by changes in octahedral distortion during electrochemical reactions, and we report an in-depth understanding of how this stabilizes the oxide structure during cycling with implications for future long-life battery material design.
RESUMEN
A photocatalyst TiO2 /Ti-BPDC-Pt is developed with a self-grown TiO2 /Ti-metal-organic framework (MOF) heterojunction, i.e., TiO2 /Ti-BPDC, and selectively anchored high-density Pt single-atomic cocatalysts on Ti-BPDC for photocatalytic hydrogen evolution. This intimate heterojunction, growing from the surface pyrolytic reconstruction of Ti-BPDC, works in a direct Z-scheme, efficiently separating electrons and holes. Pt is selectively anchored on Ti-BPDC by ligands and is found in the form of single atoms with loading up to 1.8â wt %. The selective location of Pt is the electron-enriched domain of the heterojunction, which further enhances the utilization of the separated electrons. This tailored TiO2 /Ti-BPDC-Pt shows a significantly enhanced activity of 12.4â mmol g-1 h-1 compared to other TiO2 - or MOF-based catalysts. The structure-activity relationship further proves the balance of two simultaneously exposed domains of heterojunctions is critical to fulfilling this kind of catalyst.
Asunto(s)
Estructuras Metalorgánicas , Titanio , Ingeniería , HidrógenoRESUMEN
Self-reconstruction has been considered an efficient means to prepare efficient electrocatalysts in various energy transformation process for bond activation and breaking. However, developing nano-sized electrocatalysts through complete in-situ reconstruction with improved activity remains challenging. Herein, we report a bottom-up evolution route of electrochemically reducing Cs3Rh2I9 halide-perovskite clusters on N-doped carbon to prepare ultrafine Rh nanoparticles (~2.2 nm) with large lattice spacings and grain boundaries. Various in-situ and ex-situ characterizations including electrochemical quartz crystal microbalance experiments elucidate the Cs and I extraction and Rh reduction during the electrochemical reduction. These Rh nanoparticles from Cs3Rh2I9 clusters show significantly enhanced mass and area activity toward hydrogen evolution reaction in both alkaline and chlor-alkali electrolyte, superior to liquid-reduced Rh nanoparticles as well as bulk Cs3Rh2I9-derived Rh via top-down electro-reduction transformation. Theoretical calculations demonstrate water activation could be boosted on Cs3Rh2I9 clusters-derived Rh nanoparticles enriched with multiply sites, thus smoothing alkaline hydrogen evolution.
RESUMEN
Nanocrystalline ZnO sponges doped with 5 mol% EuO1.5 are obtained by heating metal-salt complex based precursor pastes at 200-900 °C for 3 min. X-ray diffraction, transmission electron microscopy, and extended X-ray absorption fine structure (EXAFS) show that phase separation into ZnO:Eu and c-Eu2 O3 takes place upon heating at 700 °C or higher. The unit cell of the clean oxide made at 600 °C shows only ≈0.4% volume increase versus undoped ZnO, and EXAFS shows a ZnO local structure that is little affected by the Eu-doping and an average Eu3+ ion coordination number of ≈5.2. Comparisons of 23 density functional theory-generated structures having differently sized Eu-oxide clusters embedded in ZnO identify three structures with four or eight Eu atoms as the most energetically favorable. These clusters exhibit the smallest volume increase compared to undoped ZnO and Eu coordination numbers of 5.2-5.5, all in excellent agreement with experimental data. ZnO defect states are crucial for efficient Eu3+ excitation, while c-Eu2 O3 phase separation results in loss of the characteristic Eu3+ photoluminescence. The formation of molecule-like Eu-oxide clusters, entrapped in ZnO, proposed here, may help in understanding the nature of the unexpected high doping levels of lanthanide ions in ZnO that occur virtually without significant change in ZnO unit cell dimensions.
Asunto(s)
Elementos de la Serie de los Lantanoides , Óxido de Zinc , Óxido de Zinc/química , Europio/química , Difracción de Rayos XRESUMEN
Supramolecular frameworks have been widely synthesized for ion transport applications. However, conventional approaches of constructing ion transport pathways in supramolecular frameworks typically require complex processes and display poor scalability, high cost, and limited sustainability. Here, we report the scalable and cost-effective synthesis of an ion-conducting (e.g., Na+) cellulose-derived supramolecule (Na-CS) that features a three-dimensional, hierarchical, and crystalline structure composed of massively aligned, one-dimensional, and ångström-scale open channels. Using wood-based Na-CS as a model material, we achieve high ionic conductivities (e.g., 0.23 S/cm in 20 wt% NaOH at 25 °C) even with a highly dense microstructure, in stark contrast to conventional membranes that typically rely on large pores (e.g., submicrometers to a few micrometers) to obtain comparable ionic conductivities. This synthesis approach can be universally applied to a variety of cellulose materials beyond wood, including cotton textiles, fibers, paper, and ink, which suggests excellent potential for a number of applications such as ion-conductive membranes, ionic cables, and ionotronic devices.
RESUMEN
The elucidation of local structure, excitation-dependent spectroscopy, and defect engineering in lanthanide ion-doped phosphors was a focal point of research. In this work, we have studied Eu3+-doped BaZrO3 (BZOE) submicron crystals that were synthesized by a molten salt method. The BZOE crystals show orange-red emission tunability under the host and dopant excitations at 279 nm and 395 nm, respectively, and the difference is determined in terms of the asymmetry ratio, Stark splitting, and intensity of the uncommon 5D0 â 7F0 transition. These distinct spectral features remain unaltered under different excitations for the BZOE crystals with Eu3+ concentrations of 0-10.0%. The 2.0% Eu3+-doped BZOE crystals display the best optical performance in terms of excitation/emission intensity, lifetime, and quantum yield. The X-ray absorption near the edge structure spectral data suggest europium, barium, and zirconium ions to be stabilized in +3, +2, and +4 oxidation states, respectively. The extended X-ray absorption fine structure spectral analysis confirms that, below 2.0% doping, the Eu3+ ions occupy the six-coordinated Zr4+ sites. This work gives complete information about the BZOE phosphor in terms of the dopant oxidation state, the local structure, the excitation-dependent photoluminescence (PL), the concentration-dependent PL, and the origin of PL. Such a complete photophysical analysis opens up a new pathway in perovskite research in the area of phosphors and scintillators with tunable properties.
RESUMEN
The practical electrosynthesis of hydrogen peroxide (H2O2) is hindered by the lack of inexpensive and efficient catalysts for the two-electron oxygen reduction reaction (2e- ORR) in neutral electrolytes. Here, we show that Ni3HAB2 (HAB = hexaaminobenzene), a two-dimensional metal organic framework (MOF), is a selective and active 2e- ORR catalyst in buffered neutral electrolytes with a linker-based redox feature that dynamically affects the ORR behaviors. Rotating ring-disk electrode measurements reveal that Ni3HAB2 has high selectivity for 2e- ORR (>80% at 0.6 V vs RHE) but lower Faradaic efficiency due to this linker redox process. Operando X-ray absorption spectroscopy measurements reveal that under argon gas the charging of the organic linkers causes a dynamic Ni oxidation state, but in O2-saturated conditions, the electronic and physical structures of Ni3HAB2 change little and oxygen-containing species strongly adsorb at potentials more cathodic than the reduction potential of the organic linker (Eredox â¼ 0.3 V vs RHE). We hypothesize that a primary 2e- ORR mechanism occurs directly on the organic linkers (rather than the Ni) when E > Eredox, but when E < Eredox, H2O2 production can also occur through Ni-mediated linker discharge. By operating the bulk electrosynthesis at a low overpotential (0.4 V vs RHE), up to 662 ppm of H2O2 can be produced in a buffered neutral solution in an H-cell due to minimized strong adsorption of oxygenates. This work demonstrates the potential of conductive MOF catalysts for 2e- ORR and the importance of understanding catalytic active sites under electrochemical operation.
Asunto(s)
Peróxido de Hidrógeno , Estructuras Metalorgánicas , Catálisis , Oxidación-Reducción , OxígenoRESUMEN
Trivalent bismuth is a popular main group ion showing versatile luminescent behaviors in a broad spectral range from ultraviolet to visible, but barely in the near-infrared (NIR) region. In this study, we have observed unexpected NIR emission at â¼744 nm in a Bi3+-doped pyrochlore, Y2Ti2O7 (YTOB). Our first-principles electronic structure calculation and analysis of the Bi local structure via extended X-ray absorption fine structure indicate that only Bi3+ species appears in YTOB and it has a similar local environment to that of Y3+. The NIR emission is assigned to a Ti4+ â Bi3+ metal-to-metal charge transfer process. Moreover, we have demonstrated dual-mode luminescence thermometry based on the luminescence intensity ratio (LIR) and lifetime (τ) in 0.5% Bi3+ and 0.5% Pr3+ co-doped Y2Ti2O7 (YTOB0.5P0.5). It exhibits high thermometric sensitivity simultaneously in the cryogenic temperature range from 78 to 298 K based on τ of the NIR emission of Bi3+ at 748 nm and in the temperature range of 278-378 K based on the LIR of Bi3+ to Pr3+ emissions (I748/I615). As a novel LIR-τ dual-mode thermometric material over a wide temperature range, the maximum relative sensitivities of the YTOB0.5P0.5 reach 3.53% K-1 at 298 K from the τ mode and 3.52% K-1 at 318 K based on the LIR mode. The dual-mode luminescence thermometry with high responsivity from our Bi3+-based pyrochlore Y2Ti2O7 phosphor opens a new avenue for more luminescent materials toward multi-mode thermometry applied in complex temperature-sensing conditions.
RESUMEN
An overarching challenge of the electrochemical carbon dioxide reduction reaction (eCO2RR) is finding an earth-abundant, highly active catalyst that selectively produces hydrocarbons at relatively low overpotentials. Here, we report the eCO2RR performance of two-dimensional transition metal carbide class of materials. Our results indicate a maximum methane (CH4) current density of -421.63 mA/cm2 and a CH4 faradic efficiency of 82.7% ± 2% for di-tungsten carbide (W2C) nanoflakes in a hybrid electrolyte of 3 M potassium hydroxide and 2 M choline-chloride. Powered by a triple junction photovoltaic cell, we demonstrate a flow electrolyzer that uses humidified CO2 to produce CH4 in a 700-h process under one sun illumination with a CO2RR energy efficiency of about 62.3% and a solar-to-fuel efficiency of 20.7%. Density functional theory calculations reveal that dissociation of water, chemisorption of CO2 and cleavage of the C-O bond-the most energy consuming elementary steps in other catalysts such as copper-become nearly spontaneous at the W2C surface. This results in instantaneous formation of adsorbed CO-an important reaction intermediate-and an unlimited source of protons near the tungsten surface sites that are the main reasons for the observed superior activity, selectivity, and small potential.
RESUMEN
Strongly correlated electrons in layered perovskite structures have been the birthplace of high-temperature superconductivity, spin liquids, and quantum criticality. Specifically, the cuprate materials with layered structures made of corner-sharing square-planar CuO4 units have been intensely studied due to their Mott insulating ground state, which leads to high-temperature superconductivity upon doping. Identifying new compounds with similar lattice and electronic structures has become a challenge in solid-state chemistry. Here, we report the hydrothermal crystal growth of a new copper tellurite sulfate, Cu3(TeO4)(SO4)·H2O, a promising alternative to layered perovskites. The orthorhombic phase (space group Pnma) is made of corrugated layers of corner-sharing CuO4 square-planar units that are edge-shared with TeO4 units. The layers are linked by slabs of corner-sharing CuO4 and SO4. Using both the bond valence sum analysis and magnetization data, we find purely Cu2+ ions within the layers but a mixed valence of Cu2+/Cu+ between the layers. Cu3(TeO4)(SO4)·H2O undergoes an antiferromagnetic transition at TN = 67 K marked by a peak in the magnetic susceptibility. Upon further cooling, a spin-canting transition occurs at T* = 12 K, evidenced by a kink in the heat capacity. The spin-canting transition is explained on the basis of a J1-J2 model of magnetic interactions, which is consistent with the slightly different in-plane superexchange paths. We present Cu3(TeO4)(SO4)·H2O as a promising platform for the future doping and strain experiments that could tune the Mott insulating ground state into superconducting or spin liquid states.
RESUMEN
Double perovskite oxides with d8-d3 electronic configurations are expected to be ferromagnetic from the Goodenough-Kanamori rules, such as ferromagnetic La2NiMnO6. In search of new ferromagnetic insulators, double perovskite Ba2NiIrO6 was successfully synthesized by high-pressure and high-temperature methods (8 GPa and 1573 K). Ba2NiIrO6 crystallizes in a cubic double perovskite structure (space group: Fm3Ì m), with an ordered arrangement of NiO6 and IrO6 octahedra. X-ray absorption near-edge spectroscopy confirms the nominal Ni(II) and Ir(VI) valence states. Ba2NiIrO6 displays an antiferromagnetic order at 51 K. The positive Weiss temperature, however, indicates that ferromagnetic interactions are dominant. Isothermal magnetization curves at low temperatures support a field-induced spin-flop transition.
RESUMEN
The main drawbacks of today's state-of-the-art lithium-air (Li-air) batteries are their low energy efficiency and limited cycle life due to the lack of earth-abundant cathode catalysts that can drive both oxygen reduction and evolution reactions (ORR and OER) at high rates at thermodynamic potentials. Here, inexpensive trimolybdenum phosphide (Mo3 P) nanoparticles with an exceptional activity-ORR and OER current densities of 7.21 and 6.85 mA cm-2 at 2.0 and 4.2 V versus Li/Li+ , respectively-in an oxygen-saturated non-aqueous electrolyte are reported. The Tafel plots indicate remarkably low charge transfer resistance-Tafel slopes of 35 and 38 mV dec-1 for ORR and OER, respectively-resulting in the lowest ORR overpotential of 4.0 mV and OER overpotential of 5.1 mV reported to date. Using this catalyst, a Li-air battery cell with low discharge and charge overpotentials of 80 and 270 mV, respectively, and high energy efficiency of 90.2% in the first cycle is demonstrated. A long cycle life of 1200 is also achieved for this cell. Density functional theory calculations of ORR and OER on Mo3 P (110) reveal that an oxide overlayer formed on the surface gives rise to the observed high ORR and OER electrocatalytic activity and small discharge/charge overpotentials.
RESUMEN
Atomically dispersed catalysts, with maximized atom utilization of expensive metal components and relatively stable ligand structures, offer high reactivity and selectivity. However, the formation of atomic-scale metals without aggregation remains a formidable challenge due to thermodynamic stabilization driving forces. Here, a top-down process is presented that starts from iron nanoparticles, using dual-metal interbonds (RhFe bonding) as a chemical facilitator to spontaneously convert Fe nanoparticles to single atoms at low temperatures. The presence of RhFe bonding between adjacent Fe and Rh single atoms contributes to the thermodynamic stability, which facilitates the stripping of a single Fe atom from the Fe nanoparticles, leading to the stabilized single atom. The dual single-atom Rh-Fe catalyst renders excellent electrocatalytic performance for the hydrogen evolution reaction in an acidic electrolyte. This discovery of dual-metal interbonding as a chemical facilitator paves a novel route for atomic dispersion of chemical metals and the design of efficient catalysts at the atomic scale.
RESUMEN
Solar conversion of carbon dioxide (CO2) into hydrocarbon fuels offers a promising approach to fulfill the world's ever-increasing energy demands in a sustainable way. However, a highly active catalyst that can also tune the selectivity toward desired products must be developed for an effective process. Here, we present oxygen functionalized copper (OFn-Cu) nanoparticles as a highly active and methane (CH4) selective catalyst for the electrocatalytic CO2 reduction reaction. Our electrochemical results indicate that OFn-Cu (5 nm) nanoparticles with an oxidized layer at the surface reach a maximum CH4 formation current density and turnover frequency of 36.24 mA/cm2 and of 0.17 s-1 at the potential of -1.05 V vs RHE, respectively, exceeding the performance of existing Cu and Cu-based catalysts. Characterization results indicate that the surface of the OFn-Cu nanoparticles consists of an oxygen functionalized layer in the form of Cu2+ (CuO) separated from the underneath elemental Cu by a Cu+ (Cu2O) sublayer. Density functional theory calculations also confirm that presence of the O site at the CuO (101) surface is the main reason for the enhanced activity and selectivity. Using this catalyst, we have demonstrated a flow cell with an active area of 25 cm2 that utilizes solar energy to produce 7.24 L of CH4 after 10 h of continuous process at a cell power density of 30 mW/cm2.
RESUMEN
The sequestration of metal ions into the crystal structure of minerals is common in nature. To date, the incorporation of technetium(IV) into iron minerals has been studied predominantly for systems under carefully controlled anaerobic conditions. Mechanisms of the transformation of iron phases leading to incorporation of technetium(IV) under aerobic conditions remain poorly understood. Here we investigate granular metallic iron for reductive sequestration of technetium(VII) at elevated concentrations under ambient conditions. We report the retarded transformation of ferrihydrite to magnetite in the presence of technetium. We observe that quantitative reduction of pertechnetate with a fraction of technetium(IV) structurally incorporated into non-stoichiometric magnetite benefits from concomitant zero valent iron oxidative transformation. An in-depth profile of iron oxide reveals clusters of the incorporated technetium(IV), which account for 32% of the total retained technetium estimated via X-ray absorption and X-ray photoelectron spectroscopies. This corresponds to 1.86 wt.% technetium in magnetite, providing the experimental evidence to theoretical postulations on thermodynamically stable technetium(IV) being incorporated into magnetite under spontaneous aerobic redox conditions.
RESUMEN
Electrode materials which undergo anion insertion are a void in the materials innovation landscape and a missing link to energy efficient electrochemical desalination. In recent years layered hydroxides (LHs) have been studied for a range of electrochemical applications, but to date have not been considered as electrode materials for anion insertion electrochemistry. Here, we show reversible anion insertion in a LH for the first time using Co and Co-V layer hydroxides. By pairing in situ synchrotron and quartz crystal microbalance measurements with a computational unified electrochemical band-diagram description, we reveal a previously undescribed anion-insertion mechanism occurring in Co and Co-V LHs. This proof of concept study demonstrates reversible electrochemical anion insertion in LHs without significant material optimization. These results coupled with our foundational understanding of anion insertion electrochemistry establishes LHs as a materials platform for anion insertion electrochemistry with the potential for future application to electrochemical desalination.
RESUMEN
We have investigated the local environment around Mn3+ and In3+ ions in YMn1- xIn xO3 chromophores to understand the origin of the intense blue color for small values of x in these solid solutions. While X-ray diffraction results provide an average description of the trigonal bipyramidal (TBP) units about Mn/In atoms with five oxygens surrounding the cation, the X-ray absorption near edge structure (XANES) as well as extended X-ray absorption fine structure (EXAFS) of these materials clearly suggest the presence of two different TBP environments, one of which is similar to MnO5 TBP in YMnO3. EXAFS in conjunction with first-principles calculations show that replacing larger In3+ ions by smaller Mn3+ ones additionally gives rise to another TBP strongly distorted along the axial direction, expanding one of the axial Mn-O bonds by â¼11%. The relative fraction of these two environments changes in close agreement with the global stoichiometry with the elongated TBP, therefore, being dominant in the regime of the low Mn content. This local structural difference is responsible for the intense, but relatively narrow, absorption feature in the red-yellow region of the absorption spectrum, and hence YMn1- xIn xO3 appears blue for small Mn dopings. This distortion is relatively less abundant in Mn-rich compositions, and therefore, such compositions appear black, controlled by the wide absorption feature of the trigonal bipyramid coordination with Mn-O bond lengths that are essentially the same as those in YMnO3, covering the entire visible range. The chromophore properties are, thus, governed by the ratio of these two MnO5 TBP environments, one with a characteristic optical absorption giving it a blue color and the other absorbing over the entire visible range.
RESUMEN
A novel 6H-type hexagonal perovskite Ba3(Cr0.97(1)Te0.03(1))2TeO9 was prepared at high pressure (6 GPa) and temperature (1773 K). Both transmission electron microscopy and synchrotron powder X-ray diffraction data demonstrate that Ba3(Cr0.97(1)Te0.03(1))2TeO9 crystallizes in P63/mmc with face-shared (Cr0.97(1)Te0.03(1))O6 octahedral pairs interconnected with TeO6 octahedra via corner-sharing. Structure analysis shows a mixed Cr2+/Cr3+ valence state with â¼10% Cr2+. The existence of Cr2+ in Ba3(Cr2+0.10(1)Cr3+0.87(1)Te6+0.03)2TeO9 is further evidenced by X-ray absorption near-edge spectroscopy. Magnetic properties measurements show a paramagnetic response down to 4 K and a small glassy-state curvature at low temperature. In this work, the octahedral Cr2+O6 component is stabilized in an oxide material for the first time; the expected Jahn-Teller distortion of high-spin (d4) Cr2+ is not found, which is attributed to the small proportion of Cr2+ (â¼10%) and the face-sharing arrangement of CrO6 octahedral pairs, which structurally disfavor axial distortion.