RESUMEN
Designing alloys with an accurate temperature-independent electrical response over a wide temperature range, specifically a low temperature coefficient of resistance (TCR), remains a big challenge from a material design point of view. More than a century after their discovery, Constantan (Cu-Ni) and Manganin (Cu-Mn-Ni) alloys remain the top choice for strain gauge applications and high-quality resistors up to 473-573 K. Here, an average TCR is demonstrated that is up to ≈800 times smaller in the temperature range 5-300 K and >800 times smaller than for any of these standard materials over a wide temperature range (5 K < T < 1200 K). This is achieved for selected compositions of Alx CoCrFeNi high-entropy alloys (HEAs), for which a strong correlation of the ultralow TCR is established with the underlying microstructure and its local composition. The exceptionally low electron-phonon coupling expected in these HEAs is crucial for developing novel devices, e.g., hot-electron detectors, high-Q resonant antennas, and materials in gravitational wave detectors.
RESUMEN
The low cost, rare earth free τ-phase of MnAl has high potential to partially replace bonded Nd2Fe14B rare earth permanent magnets. However, the τ-phase is metastable and it is experimentally difficult to obtain powders suitable for the permanent magnet alignment process, which requires the fine powders to have an appropriate microstructure and high τ-phase purity. In this work, a new method to make high purity τ-phase fine powders is presented. A high purity τ-phase Mn0.55Al0.45C0.02 alloy was synthesized by the drop synthesis method. The drop synthesized material was subjected to cryo milling and followed by a flash heating process. The crystal structure and microstructure of the drop synthesized, cryo milled and flash heated samples were studied by X-ray in situ powder diffraction, scanning electron microscopy, X-ray energy dispersive spectroscopy and electron backscatter diffraction. Magnetic properties and magnetic structure of the drop synthesized, cryo milled, flash heated samples were characterized by magnetometry and neutron powder diffraction, respectively. The results reveal that the 2 and 4 hours cryo milled and flash heated samples both exhibit high τ-phase purity and micron-sized round particle shapes. Moreover, the flash heated samples display high saturation magnetization as well as increased coercivity.
RESUMEN
The hydride Ba(3)Si(4)H(x) (x = 1-2) was prepared by sintering the Zintl phase Ba(3)Si(4), which contains Si(4)(6-) butterfly-shaped polyanions, in a hydrogen atmosphere at pressures of 10-20 bar and temperatures of around 300 °C. Initial structural analysis using powder neutron and X-ray diffraction data suggested that Ba(3)Si(4)H(x) adopts the Ba(3)Ge(4)C(2) type [space group I4/mcm (No. 140), a ≈ 8.44 Å, c ≈ 11.95 Å, Z = 8] where Ba atoms form a three-dimensional array of corner-condensed octahedra, which are centered by H atoms. Tetrahedron-shaped Si(4) polyanions complete a perovskite-like arrangement. Thus, hydride formation is accompanied by oxidation of the butterfly polyanion, but the model with the composition Ba(3)Si(4)H is not charge-balanced. First-principles computations revealed an alternative structural scenario for Ba(3)Si(4)H(x), which is based on filling pyramidal Ba5 interstices in Ba(3)Si(4). The limiting composition is x = 2 [space group P4(2)/mmm (No. 136), a ≈ 8.4066 Å, c ≈ 12.9186 Å, Z = 8], and for x > 1, Si atoms also adopt tetrahedron-shaped polyanions. Transmission electron microscopy investigations showed that Ba(3)Si(4)H(x) is heavily disordered in the c direction. Most plausible is to assume that Ba(3)Si(4)H(x) has a variable H content (x = 1-2) and corresponds to a random intergrowth of P- and I-type structure blocks. In either form, Ba(3)Si(4)H(x) is classified as an interstitial hydride. Polyanionic hydrides in which H is covalently attached to Si remain elusive.