Chitin extraction from crab shells and synthesis of chitin @metakaolin composite for efficient amputation of Cr (VI) ions.

The present research study combines chitin from shrimp waste with the oxide-rich metakaolin. Metakaolin is a blend of mixed oxides rich in silica and alumina with good adsorbent properties. The chitin@metakaolin (CHt@M.K.) composite was synthesized and characterized using FTIR, SEM, TGA, XRD and XPS techniques. Cr(VI) removal studies were compared for chitin and CHt@M.K. through adsorption. It was found that the adsorption capacity of CHt@M.K. is 278.88 mg/g, almost double that of chitin, at pH 5.0 in just 120 min of adsorption. Isotherm models like Langmuir, Freundlich, Temkin and Dubinin-Radushkevich were investigated to comprehend the adsorption process. It was revealed that Langmuir adsorption isotherm is most suitable to elucidate Cr(VI) adsorption on CHt@M.K. The adsorption kinetics indicate that pseudo first order was followed, indicating that the physisorption was the process that limited the sorption process rate. The positive enthalpy change (20.23 kJ/mol) and positive entropy change (0.083 kJ/mol K) showed that the adsorption process was endothermic and more random at the solid-liquid interface. The negative free energy change over entire temperature range was an indicator of spontaneity of the process. Apart from all these, the non-covalent interactions between Cr(VI) and composite were explained by quantum calculations based models.

Efficient multi-ion adsorption using chitosan-malonic acid film: Enhancement using response surface methodology.

The objective of this research is to conduct a comprehensive characterization of chitosan while also improving its attributes by crosslinking with malonic acid, with a focus on its efficacy in removing hexavalent chromium, arsenite and fluoride ions. Crosslinking chitosan in 1:0.5 mass ratio forming a film led to substantial enhancement in confiscation of these target pollutants. The characterization of the adsorbent involved several techniques, including FT-IR, TGA-DSC, SEM-EDX, XRD, and BET surface area analysis. In batch adsorption experiments, Chitosan-malonic acid (CMA) was employed to remove CrVI, AsIII and F- from aqueous solutions. These experiments were conducted while varying conditions such as pH, dosage, concentration, temperature, and time. Through the implementation of response surface methodology (RSM), parameters were optimized, resulting in over 95% removal of CrVI, AsIII and F- ions. The isotherm and kinetics data demonstrated a good fit with the Langmuir isotherm model and pseudo second-order kinetics, respectively. According to the Langmuir isotherm, the maximum adsorption capacities on CMA for CrVI, AsIII and F- were determined to be 687.05 mg g-1, 26.72 mg g-1 and 51.38 mg g-1 respectively under optimum pH of 4.0, 7.0 and 5.0 respectively under ambient temperature of 303 K. Thermodynamic analysis indicated that the adsorption process was spontaneous and driven by enthalpy. The regenerability of the adsorbent was validated through five adsorption-desorption cycles, signifying its reusability. An assessment of the adsorbent's sustainability indicated an eco-friendly synthesis, as reflected by the low E-factor value of 0.0028.

Multifunctional Cross-Linked Shrimp Waste-Derived Chitosan/MgAl-LDH Composite for Removal of As(V) from Wastewater and Antibacterial Activity.

This work synthesized a novel chitosan-loaded MgAl-LDH (LDH = layered double hyroxide) nanocomposite, which was physicochemically characterized, and its performance in As(V) removal and antimicrobial activity was evaluated. Chitosan-loaded MgAl-LDH nanocomposite (CsC@MgAl-LDH) was prepared using cross-linked natural chitosan from shrimp waste and modified by Mg-Al. The main mechanisms predominating the separation of As(V) were elucidated. The characteristic changes confirming MgAl-LDH modification with chitosan were analyzed through Fourier transform infrared spectroscopy, X-ray diffraction, thermogravimetric analysis-differential thermal analysis, and Brunauer-Emmett-Teller measurements. Porosity and the increased surface area play an important role in arsenic adsorption and microbial activity. Adsorption kinetics follows the general order statistically confirmed by Bayesian Information Criterion differences. To understand the adsorption process, Langmuir, Freundlich, and Liu isotherms were studied at three different temperatures. It was found that Liu's isotherm model was the best-fitted model. CsC@MgAl-LDH showed the maximum adsorption capacity of 69.29 mg g-1 toward arsenic at 60 °C. It was observed that the adsorption capacity of the material rose with the increase in temperature. The spontaneous behavior and endothermic nature of adsorption was confirmed by the thermodynamic parameters study. Minimal change in percentage removal was observed with coexisting ions. The regeneration of material and adsorption-desorption cycles revealed that the adsorbent is economically efficient. The nanocomposite was very effective against Staphylococcus aureus and Bacillus subtilus.

Tin(IV) cross-linked chitosan for the removal of As(III).

Chitosan, a potent amino polysaccharide, has been cross-linked with Sn(IV) chloride. The material was thoroughly characterized using FT-IR, XRD, SEM, EDX, TGA-DTA and BET studies. This Sn(IV) chloride cross-linked chitosan (Sn-Ch) has been exploited for As(III) adsorption. Various parameters like pH, amount of adsorbent, adsorption time etc have been optimized to achieve maximum adsorption efficiency. Under optimum conditions of pH 7.0±0.2, adsorption time of 45min and adsorbent dose 200mg, Sn-Ch was found to have adsorption capacity of 17.10mg/g at 298K. Adsorption of As(III) by Sn-Ch follow non-linear Freundlich isotherm model. The equilibrium studies showed that the experimental data fits well with non-linear pseudo-second-order kinetic model. Adsorption process was found to be exothermic and spontaneous. Column study proves the applicability of Sn-Ch to the larger sample volumes. It was found to be recyclable material and could be regenerated and reused multiple times adding a greener dimension.

Stannic chloride impregnated chitosan for defluoridation of water.

Chitosan, a potent amino polysaccharide, has been impregnated with Sn(IV) chloride for effective adsorption of fluoride from water. The Sn(IV) chloride impregnated chitosan was synthesized using microwave assisted technique. The material was thoroughly characterized using FTIR, SEM, EDX and XRD. The decrease in surface area and pore volume has been revealed from BET studies. Enhanced thermal stability of this material was ascertained by TGA-DTA studies. This Sn(IV) chloride impregnated chitosan(Sn-Ch) has been exploited for its defluoridation property. Various parameters like pH, amount of adsorbent, adsorption time etc have been optimized to achieve maximum defluoridation efficiency. Under optimum conditions, Sn-Ch was found to have adsorption capacity of 17. 63mg/g. The equilibrium studies showed that the data fits well with Freundlich isotherm model. Thermodynamics and kinetics parameters have been evaluated. The material has been applied for the defluoridation of real water sample. It was found to be recyclable material and can be regenerated and reused multiple times adding a greener dimension.

Removal of Cd(II) and Hg(II) from effluents by ionic solid impregnated chitosan.

Ethylhexadecyldimethyl ammonium bromide impregnated chitosan (EHDAIC) was prepared to remove cadmium and mercury from synthetic effluent. The adsorbent was characterized by FTIR, XRD, SEM, EDX and TGA-DTA. Adsorption studies were carried out under different conditions of pH, adsorbent dose, temperature, and contact time. The results showed that the adsorption capacity of EHDAIC is a function of the solution pH and the optimum pH for these metal ions was found to be 3.0. The equilibrium data has been described using Langmuir and Freundlich isotherm models. The maximum adsorption capacity of 341.30mg/g was observed for Cd(II) and 43.43mg/g for Hg(II) in accordance with Langmuir adsorption isotherm in the form of their chloro complexes. The kinetic data fitted well with pseudo-second-order model, and equilibrium data was found to follow Freundlich isotherm model. The calculated thermodynamic parameters showed that the adsorption process was feasible, exothermic and spontaneous. Effect of common excipient ions was studied. Also the material was tested for large sample volumes using column extraction process. The adsorbent material could be regenerated for repetitive applications.