Revised evaluation objectives of the Korean Dentist Clinical Skill Test: a survey study and focus group interviews

PURPOSE: This study aimed to propose a revision of the evaluation objectives of the Korean Dentist Clinical Skill Test by analyzing the opinions of those involved in the examination after a review of those objectives. METHODS: The clinical skill test objectives were reviewed based on the national-level dental practitioner competencies, dental school educational competencies, and the third dental practitioner job analysis. Current and former examinees were surveyed about their perceptions of the evaluation objectives. The validity of 22 evaluation objectives and overlapping perceptions based on area of specialty were surveyed on a 5-point Likert scale by professors who participated in the clinical skill test and dental school faculty members. Additionally, focus group interviews were conducted with experts on the examination. RESULTS: It was necessary to consider including competency assessments for "emergency rescue skills" and "planning and performing prosthetic treatment." There were no significant differences between current and former examinees in their perceptions of the clinical skill test's objectives. The professors who participated in the examination and dental school faculty members recognized that most of the objectives were valid. However, some responses stated that "oromaxillofacial cranial nerve examination," "temporomandibular disorder palpation test," and "space management for primary and mixed dentition" were unfeasible evaluation objectives and overlapped with dental specialty areas. CONCLUSION: When revising the Korean Dentist Clinical Skill Test's objectives, it is advisable to consider incorporating competency assessments related to "emergency rescue skills" and "planning and performing prosthetic treatment."

Three-axis load analysis of high-speed handpiece on dental training teeth and computer-aided design/computer-aided manufacturing blocks.

This study aimed to evaluate and compare the mechanical properties of dental training teeth with subtractive and additive computer-aided design/computer-aided manufacturing (CAD/CAM) materials used to fabricate dental simulation models. Therefore, the three-axis load generated during cutting movements, including drilling and milling performed using a dental handpiece, was measured and compared. The samples were cut vertically downward by 1.5 mm, horizontally by 6 mm, and vertically upward at a constant speed (1 mm/s), while the rotational speed of the bur was maintained at 200,000 rotations per minute. A three-axis load cell was used to measure the X-, Y-, and Z-axis loads on the specimen. The median value of the X-, Y-, and Z-axis measurements and the resultant load during the vertical-downward, horizontal, and vertical-upward movements were compared using a one-way analysis of variance and Tukey's post hoc test. For vertical downward movement, the drilling force of the dental training teeth was lower than that of Vita Enamic® and similar to that of Lava™ Ultimate. In contrast to subtractive CAD/CAM blocks, the drilling force of the dental training teeth was higher than that of 3D-printed resin blocks. Regarding horizontal movement, the milling force of dental training teeth was lower than that of Vita Enamic®. In contrast, the milling force of Nissin was similar to that of Lava™ Ultimate, while that of Frasaco was lower. Furthermore, compared to additive CAD/CAM blocks, the milling force of the dental training teeth was higher than that of 3D-printed resin blocks. Regarding vertical upward movement, the resultant loads of dental training teeth was lower than that of Vita Enamic®. Similarly, the resultant load of Nissin was similar to that of Lava™ Ultimate, while that of Frasaco was lower. Additionally, compared to additive CAD/CAM blocks, the resultant loads of the dental training teeth were similar to those of the 3D-printed resin blocks.

A prospective multicenter clinical study on the efficiency of detachable ball- and spring-retained implant prosthesis.

PURPOSE: This prospective clinical study was conducted to evaluate the clinical usefulness of the freely detachable zirconia ball- and spring-retained implant prosthesis (BSRP) through a comparative analysis of screw- and cement-retained implant prosthesis (SCRP). MATERIALS AND METHODS: A multi-center, randomized, prospective clinical study evaluating the clinical usefulness of the detachable zirconia ball- and spring-retained implant prostheses was conducted. Sixty-four implant prostheses in 64 patients were examined. Periodic observational studies were conducted at 0, 3, 6, and 12 months after delivery of the implant prosthesis. Factors such as implant success rate, marginal bone resorption, periodontal pocket depth, plaque and bleeding index, and prosthetic complications were evaluated, respectively. RESULTS: During the 1-year observation period, all implants survived without functional problems and clinical mobility, showing a 100% implant success rate. Marginal bone resorption was significantly higher in the SCRP group than in the BSRP group only at the time of implant prosthesis delivery (P = .043). In all observation periods, periodontal pocket depth was slightly higher in the BSRP group than in the SCRP group, but there was no significant difference (P > .05). The modified plaque index (mPI) scores of both groups were moderate. Higher ratio of a score 2 in modified sulcus bleeding index (mBI) was observed in the BSRP group in the 6- and 12-months observation. CONCLUSION: Within the limitations of this study, the newly developed zirconia ball- and spring-retained implant prosthesis could be considered as an applicable and predictable treatment method along with the existing screw- and cement-retained prosthesis.

3D analysis of occlusal registration through geometry embedded library matching between quadrant and full-arch digital impression.

OBJECTIVE: This study aimed to compare the accuracy of occlusal registration for single-unit restorations in the posterior area of the jaw using the complete-arch or quadrant scan techniques. MATERIALS AND METHODS: A master cast was prepared and articulated on a nonadjustable articulator, and the maxillary left first molar was prepared for a full-coverage crown. The master cast was digitized as the reference data using a laboratory scanner (E3 scanner, 3Shape, Copenhagen, Denmark). It was scanned 10 times in the complete arch and 10 times in the quadrant, with an occlusal registration in each, using four intraoral scanners (i500, Primescan, TRIOS 3, and TRIOS 4). The scanned data were aligned to the reference data using GOM Inspect software. A three-dimensional analysis of the surface-based occlusal clearance and angular deviation, focusing on the prepared tooth, was performed. RESULTS: The mean surface-based occlusal clearance in the quadrant and complete-arch scans was 1.622 ± 0.032 mm and 1.642 ± 0.043 mm, respectively. Angular deviations compared to the reference cast showed a difference of 0.10° distally and 0.09° buccally for the quadrant scan and 0.12° distally and buccally for the complete-arch scan. Statistical analysis was performed using one-way analysis of variance and post hoc Scheffe's test. No significant differences were observed between the test groups. CONCLUSIONS: No significant differences were found between occlusal registrations of the complete-arch and quadrant scans. Therefore, a quadrant scan can achieve the same outcome as a complete-arch scan for single-unit restoration in the posterior area of the jaw. CLINICAL RELEVANCE: Quadrant scanning for single-unit restoration showed similar outcomes as complete-arch scans.

Effects of heat-treatment methods on cytocompatibility and mechanical properties of dental products 3D-printed using photopolymerized resin.

PURPOSE: The purpose of this study was to test heat-treatment methods for improving the cytocompatibility of dental 3D printable photopolymer resins. METHODS: Nextdent C&B resin and a digital light processing 3D printer were used to print all specimens, which were divided into seven groups as follows: 1-month storage at controlled room temperature, 20 to 25 °C (RT), 24-hour storage at RT, 24-hour storage in RT water, 1-min immersion in 80 °C water, 1-min immersion in 100 °C water, 5-min immersion in 100 °C water, and autoclaving. Cell viability tests, cytotoxicity tests, and confocal laser scanning microscopy were performed to analyze the cytocompatibility of the 3D-printed resin. Fourier-transform infrared spectroscopy was performed after heat-treatment to determine the degree of conversion (DC). RESULTS: Immersing printed resin samples in 100 °C water for 1 or 5 min after the curing process was an effective method for increasing cytocompatibility by inducing the preleaching of toxic substances such as unpolymerized monomers, photoinitiators, and additives. Moreover, the DC can be increased by additional polymerization without affecting the mechanical properties of the material. CONCLUSIONS: Immersing the printed photosensitive dental resins in 100 °C water for 5 min is a suitable method for increasing cytocompatibility and the DC.

Influence of postwashing process on the elution of residual monomers, degree of conversion, and mechanical properties of a 3D printed crown and bridge materials.

OBJECTIVES: This study aimed to determine the effects of the postwashing method and time on the mechanical properties and biocompatibility of three-dimensional (3D) printed crown and bridge resin. METHODS: DLP (digital light processing)-printed specimens produced from Nextdent crown & bridge (C&B) resins were washed separately using an ultrasonic bath and rotary washer with TPM (tripropylene glycol monomethyl ether) for 3 min, 6 min, 10 min, 20 min, and 1 h. Postcuring was applied for 30 min to each specimen after the washing process. The flexural strength, Vickers hardness, water sorption and solubility, degree of conversion (DC), elution of residual monomers, and biocompatibility of the specimens were evaluated. RESULTS: The ultrasonic bath showed greater washing efficacy by reducing the residual HEMA (2-hydroxyethyl methacrylate) from 2.0634 ppm to 0.1456 ppm and reducing the residual TEGDMA (triethylene glycol dimethacrylate) from 1.4862 ppm to 0.1484 ppm. With prolonged washing, the flexural strength significantly decreased from 129.67 ± 6.66 MPa (mean±standard deviation) to 103.17 ± 7.20 MPa, while the Vickers hardness increased slightly for the first 6 min and then decreased thereafter significantly. The DC was 87.78 ± 1.34% after 3 min and then gradually decreased with extended washing time. The cytotoxicity significantly decreases with the increment of the washing time. SIGNIFICANCE: The washing effect on the elution of residual monomers was better for an ultrasonic bath than for a rotary washer. Extending the washing time reduces the mechanical properties and cytotoxicity of the Nextdent C&B resin.

Accuracy of 3D printed models and implant-analog positions according to the implant-analog-holder offset, inner structure, and printing layer thickness: an in-vitro study.

PURPOSE: This study aimed to determine how the implant-analog-holder (IAH) offset, inner structure, and printing layer thickness influence the overall accuracy and local implant-analog positional changes of 3D printed dental models. METHODS: Specimens in 12 experimental groups (8 specimens per group) with different IAH offsets, inner structures, and printing layer thicknesses were printed in three dimensions using an LCD printer (Phrozen Shuffle) and digitized by a laboratory scanner (Identica T500). The trueness and precision of the printed model as well as the angular distortion, depth deviation, and linear distortion of the implant analog were evaluated using three-way ANOVA. RESULTS: The positional accuracy was significantly higher for IAH offsets of 0.04 mm and 0.06 mm than for one of 0.08 mm, for a hollow than a solid inner structure, and for a printing layer thickness of 100 µm than for one of 50 µm (all P<.001). CONCLUSIONS: The accuracies of the 3D printed models and the implant-analog positions were significantly affected by the IAH offset, inner structure, and printing layer thickness. CLINICAL SIGNIFICANCE: Given the observation of this study, premeditating the IAH offset of 0.06 mm, hollow inner structure, and printing layer thickness of 100 µm before printing can help clinicians reach the optimum overall printing accuracy and minimum the local positional changes of the implant-analogs.

A Digital Workflow for the Fabrication of a Milled Removable Partial Denture.

Complete dentures fabricated with the additive or subtractive method have been widely used and proven to be clinically acceptable. However, fabrication of removable partial dentures (RPDs) using computer-aided design and computer-aided manufacturing is limited by its technique sensitivity as the pink resin, which encases part of metal framework, cannot be fabricated digitally. This article introduces a digital workflow to fabricate an RPD with the subtractive method. A complex structure of the offset metal framework and denture base with teeth sockets was milled with this technique. Artificial teeth were milled with a resin disk according to the computer-aided design data, resulting in the customized occlusal surface. This digital technique can be an alternative to the analog fabrication method as the RPD was fabricated digitally, keeping the original structures and reducing resin shrinkage on the intaglio surface.

Effects of postpolymerization conditions on the physical properties, cytotoxicity, and dimensional accuracy of a 3D-printed dental restorative material.

STATEMENT OF PROBLEM: Although the introduction of high-speed 3-dimensional (3D) printing technology has significantly reduced printing time, the time required for postpolymerization is a speed-determining step because of the long wait time. How postpolymerization conditions affect material properties is unclear. PURPOSE: The purpose of this in vitro study was to assess the physical properties, accuracy, and biosafety of a 3D-printed dental restorative material according to postpolymerization conditions. MATERIAL AND METHODS: Specimens were prepared by 3D printing with a digital light processing 3D printer with 1 interim dental material (C&B MFH). All printed specimens underwent a postpolymerization process with 5 different postpolymerization devices and were designated as groups D1 (D102H), FO (Form Cure), LC (LC-3DPrintBox), ME (Medusa), and MP (MP100). The light intensity and temperature of each device were measured, and the Vickers hardness, flexural strength and modulus, degree of conversion (DC), cytotoxicity, and polymerization shrinkage were analyzed. Statistical analyses were conducted with 1-way analysis of variance, the Tukey post hoc test, and regression testing (α=.05). Scanning electron microscopy was used to assess the fracture surface characteristics of the specimens. RESULTS: Light intensity was strongest with the ME device, and the temperature inside the device during postpolymerization showed the highest increase with the LC device and the lowest increase with the D1 device. The LC group specimens showed the highest mean Vickers hardness, and the MP group showed the lowest. The flexural strength was ≥100 MPa in all groups, with a flexural modulus ranging from 1.17 to 1.5 GPa. The DC results were similar to the physical properties test results. The D1, FO, LC, and ME groups all showed ≥70% cell viability, indicating no toxicity. The FO group showed the highest shrinkage rate of 0.52%. CONCLUSIONS: When the light intensity was strong, the surface was sufficiently hard, and toxic substances were not eluted even after a short postpolymerization time, suggesting that light intensity modulation and time management can be used to improve the postpolymerization process.

Evaluation of different registration methods and dental restorations on the registration duration and accuracy of cone beam computed tomography data and intraoral scans: a retrospective clinical study.

OBJECTIVES: To evaluate whether the accuracy and duration of registration for cone beam computed tomography (CBCT) and intraoral scans differ according to the method of registration and ratio of dental restorations to natural teeth. MATERIALS AND METHODS: CBCT data and intraoral scans of eligible patients were grouped as follows according to the ratio of the number of dental restorations to the number of natural teeth (N): group 1, N = 0%; group 2, 0% < N < 50%; group 3, 50% ≤ N < 100%; and group 4, 100% ≤ N. Marker-free registration was performed with a deep learning-based platform and four implant planning software with different registration methods (two point-based, one surface-based, and one manual registration software) by a single operator, and the time consumption was recorded. Registration accuracy was evaluated by measuring the distances between the three-dimensional models of CBCT data and intraoral scans. RESULTS: A total of 36 patients, one jaw per patient, were enrolled. Although registration accuracy was similar, the time consumed for registration significantly differed for the different methods. The deep learning-based registration method consumed the least time. Greater proportions of dental restorations significantly reduced the registration accuracy for semi-automatic and deep learning-based methods and reduced the time consumed for semi-automatic registration. CONCLUSIONS: No superiority in registration accuracy was found. The proportion of dental restorations significantly affects the accuracy and duration of registration for CBCT data and intraoral scans. CLINICAL TRIAL REGISTRATION: ClinicalTrials.gov Identifier: KCT0006710 CLINICAL RELEVANCE: Registration accuracy for virtual implant planning decreases when the proportion of dental restorations increases regardless of registration methods.

Influence of different postcuring parameters on mechanical properties and biocompatibility of 3D printed crown and bridge resin for temporary restorations.

This study analyzed the flexural properties, Vickers hardness, degree of conversion (DC), and cell viability of 3D printed crown and bridge resin postcured using various types of postcuring equipment (PCE). 3D printed specimens were postcured for various times using different types of 3D printing PCE [for 5, 15, and 30 min using LC 3D Print Box (LC), Form Cure (FC), Cure M (CM), and Veltz 3D (VE) devices] and the VALO handheld light-curing (VA) device for 20, 40, and 60 s. Neither the flexural strength (132.27-145.79 MPa) nor the flexural modulus (1.52-1.83 GPa) differed significantly when postcuring for 30 min using the LC, FC, CM, or VE device, or for 20, 40, or 60 s of postcuring using the VA device (p > 0.05). The Vickers hardness was highest after 30 min of postcuring for all groups, and varied significantly with the postcuring time in the LC (p < 0.001) and CM (p < 0.001) groups. DC was significantly higher for the 5-min CM group (84.97 ± 4.02%) than for the GS, 30-min FC, 5-min VE, and 20-s VA groups. Cell viability of the postcured resin specimens was 56.46-92.29%, and varied significantly in the CM and VE groups according to the postcuring time (p < 0.05). Confocal laser scanning microscopy observations showed well-developed cell morphology and numerous cell-cell contacts in all groups except the GS group. This study found that the use of different types of PCE did not significantly affect the flexural properties of 3D printed crown and bridge resin, whereas there were significant variations in DC, Vickers hardness, and cell viability.

Application of additive and subtractive manufacturing technology for a digitally fabricated removable partial denture after a partial maxillectomy: A clinical report.

This clinical report describes the treatment of a patient with a large defect area in the maxillary central incisor, left lateral incisor, canine, and first premolar area after a partial maxillectomy. Computer-aided design and computer-aided manufacturing (CAD-CAM) techniques including rapid prototyping and milling were applied together to fabricate a removable partial denture.

Dental students' perceptions on a simulated practice using patient-based customised typodonts during the transition from preclinical to clinical education.

PURPOSE/OBJECTIVES: Dental students experience difficulties during the transition from preclinical to clinical curriculum. In order to help the students to adapt to the clinical education programme, a simulated practice using patient-based customised models was introduced in this study to prepare for their first clinical practice. METHODS: This study included 45 third-year predoctoral students (D3 students) who were about to perform the preparation of a single crown abutment on their first patient. After practicing abutment preparation using simulated models and providing the actual treatment to their own patient, the students were surveyed to investigate their perceptions on the simulated practice using the 3D-printed customised typodont model. The statistical analysis of the quantitative data and the thematic analysis of the qualitative data were conducted. RESULTS: Regarding this simulation, more than 80% of the students gave positive feedback on their practice of (a) operative positions and postures, (b) finger rest, (c) occlusal reduction, (d) axial reduction and (e) proximal reduction. Student responses on the open-ended questions about how they perceived the usefulness of this simulation were categorised as "First clinical case," "Patient-based model" and "Realistic simulation environment." In addition, a number of improvements of the simulation were also suggested by the students including the typodont and the manikin. CONCLUSIONS: This study gives insights into the significance of simulated practice using patient-based customised typodonts as a transitional education tool and its direction of development in the field of restorative treatments accompanied by irreversible tooth preparations.

Sleeve insert scan body to predict implant placement position by using implant surgical guides: A dental technique.

In studies that assessed the accuracy of implant surgical guides, evaluations were based on the placement position of the implant by using a manufactured surgical guide. However, such assessments could involve errors that may occur during implant placement. Therefore, evaluating the 3-dimensional accuracy of the fabrication of the implant surgical guide itself is not enough. In the evaluation method described in this article, location-related information is obtained by connecting a scan body to the sleeve of the surgical guide instead of directly placing the implant. This helps to evaluate the accuracy of the surgical guide without errors in the placement of an implant.

Evaluating the Three-Dimensional Printing Accuracy of Partial-Arch Models According to Outer Wall Thickness: An In Vitro Study.

The printing accuracy of three-dimensional (3D) dental models using photopolymer resin affects dental diagnostic procedures and prostheses. The accuracy of research into the outer wall thickness and printing direction data for partial-arch model printing has been insufficient. This study analyzed the effects of wall thickness and printing direction accuracy. Anterior and posterior partial-arch models were designed with different outer wall thicknesses. After 3D printing, a trueness analysis was performed. Those with full-arch models were the control group. The full-arch model had an error value of 73.60 ± 2.61 µm (mean ± standard deviation). The error values for the partial-arch models with 1-, 2-, and 3-mm thick outer walls were 54.80 ± 5.34, 47.58 ± 7.59, and 42.25 ± 9.19 µm, respectively, and that for the fully filled model was 38.20 ± 4.63 µm. The printing accuracies differed significantly between 0 degrees and 60 degrees, at 49.54 ± 8.16 and 40.66 ± 6.80 µm, respectively (F = 153.121, p < 0.001). In conclusion, the trueness of the partial-arch model was better than that of the full-arch model, and models with thick outer walls at 60 degrees were highly accurate.

Evaluation of Dimensional Changes According to Aging Period and Postcuring Time of 3D-Printed Denture Base Prostheses: An In Vitro Study.

During the three-dimensional (3D) printing process of a dental prosthesis, using photopolymer resin, partially polymerized resin is further cured through the postcuring process that proceeds after the printing, which improves the stability of the printed product. The mechanical properties of the end product are known to be poor if the postcuring time is insufficient. Therefore, this study evaluated the effect of the postcuring time of the 3D-printed denture base on its dimensional stability, according to the aging period. The 3D prints were processed after designing maxillary and mandibular denture bases, and after the following postcuring times were applied: no postcuring, and 5, 15, 30, and 60 min. The dimensional stability change of the denture base was evaluated and analyzed for 28 days after the postcuring process. The trueness analysis indicated that the mandibular denture base had lower output accuracy than the maxillary denture base, and the dimensional stability change increased as postcuring progressed. In the no postcuring group for the mandible, the error value was 201.1 ± 5.5 µm (mean ± standard deviation) after 28 days, whereas it was 125.7 ± 13.0 µm in the 60 min postcuring group. For both the maxilla and the mandible, shorter postcuring times induced larger dimensional stability changes during the aging process. These findings indicate that in order to manufacture a denture base with dimensional stability, a sufficient postcuring process is required during the processing stage.

Effects of Artificial Tooth Brushing and Hydrothermal Aging on the Mechanical Properties and Color Stability of Dental 3D Printed and CAD/CAM Materials.

This study analyzed the surface roughness and waviness, Vickers hardness (VHN), and color changes of six types of 3D printed resins and computer-aided design/computer-aided manufacturing (CAD/CAM) materials after artificial toothbrushing. The average surface roughness height (Ra) change of Formlabs denture teeth A2 resin (FMLB) was not significant between after artificial toothbrushing (0.17 ± 0.02 µm and 0.17 ± 0.05 µm, respectively; mean ± standard deviation). However, the Ra value increased significantly in all remaining groups. Regarding waviness, polymethylmethacrylate (PMMA) had the largest increases in average waviness height (Wa) and maximum surface waviness height (Wz) between, before (0.43 ± 0.23 µm and 0.08 ± 0.02 µm), and after (8.67 ± 4.03 µm, 1.30 ± 0.58 µm) toothbrushing. There were no significant changes in Wa for Formlabs denture teeth A2 resin (FMLB) and NextDent C&B (NXT). After artificial toothbrushing, the dispersed-filler composite (DFC) group had the largest color difference (ΔE, of 2.4 ± 0.9), and the remaining materials had smaller changes than the clinical acceptance threshold of ΔE = 2.25. The VHN of FMLB and NXT were 9.1 ± 0.4 and 15.5 ± 0.4, respectively, and were not affected by artificial toothbrushing. The flexural strengths of the 3D printed materials were 139.4 ± 40.5 MPa and 163.9 ± 14.0 MPa for FMLB and NXT, respectively, which were similar to those of the polycarbonate and PMMA groups (155.2 ± 23.6 MPa and 108.0 ± 8.1 MPa, respectively). This study found that the evaluated 3D printed materials had mechanical and optical properties comparable to those of CAD/CAM materials and were stable even after artificial toothbrushing and hydrothermal aging.

Effect of Acid Mixtures on Surface Properties and Biaxial Flexural Strength of As-Sintered and Air-Abraded Zirconia.

The aim of this work was to evaluate the effects of application time of an acid mixture solution on the surface roughness, phase transformation, and biaxial flexural strength of 3Y-TZP after sintering or air abrasion. For the biaxial flexural strength measurement, 220 3Y-TZP disk-shaped specimens were prepared after as-sintering or air abrasion. The etching solution comprised a mixture of hydrofluoric acid, sulfuric acid, hydrogen peroxide, methyl alcohol, and purified water. The samples were divided into 11 subgroups according to the etching times (Control, 1, 2, 3, 5, 8, 10, 12, 15, 20, and 30 min). The results showed that acid treatment on both as-sintered and air-abraded 3Y-TZP surfaces increased the surface roughness. However, it had no significant effects on the monoclinic phase or flexural strength of as-sintered zirconia. The monoclinic phase and flexural strength of air-abraded zirconia increased sharply after air abrasion; however, they gradually decreased after acid treatment, to a similar level to the case of the untreated surface. Surface treatment with acid mixture increased the roughness, but the lack of increase of monoclinic phase is thought to be because the loose monoclinic particles remaining on the surface were removed through the etching process.

A Comparison of Accuracy of Different Dental Restorative Materials between Intraoral Scanning and Conventional Impression-Taking: An In Vitro Study.

The properties of underlying substrates influence the quality of an intraoral scan, but few studies have compared the outcomes using common restorative materials. In this study, we aimed to compare the accuracy of digital and conventional impressions recorded for four different dental materials as the substrates. Experimental crowns were produced with a metallic surface (gold or cobalt-chromium alloy (Co-Cr)) or without a metallic surface (zirconia or PMMA (polymethyl methacrylate)). A conventional impression was made in the conventional group (CON group), and gypsum models were subsequently scanned with a tabletop scanner. An intraoral scanner was used to scan the crowns either after applying a powder spray to reduce the surface reflectivity (IOS-P group) or without the powder spray (IOS group). The scans were assessed in three dimensions for precision and trueness. The accuracy did not differ between the CON and IOS groups for the non-metallic crowns. However, it was statistically different for the Co-Cr metallic crown, reducing trueness observed between groups as CON > IOS > IOS-P. The study evidences the differences in outer surface accuracy observed with a change in the substrate material to be imaged using an oral scanner and with the impression method. These findings suggest that the restoration material present in the oral cavity should be considered when selecting an impression-taking method.