Hydrothermally formed mesoporous SnO2 was used as a support for nickel chemical deposition and, after subsequent thermal treatment, a high specific surface area (36 m2 g-1) Ni/SnO2 material was obtained. XPS analysis has shown that in the Sn 3d region the spectrum is similar to that of pristine SnO2, whereas Ni species are present on the surface as NiO, Ni2O3 and Ni(OH)2. Mixing Ni/SnO2 with a small amount of Black Pearls (BP) leads to a significant enhancement of the resulting Ni/SnO2-BP composite activity for nitrite anodic oxidation, presumably due to the higher surface area (115 m2 g-1), to better electrical conductivity and to a certain contribution of the BP to an increase in surface density of the active sites. Ni/SnO2-BP also outperforms pristine BP (in terms of Tafel slopes and electron-transfer rates), most likely due to the fact that the Ni(II)/Ni(III) couple can act as an electrocatalyst for nitrite oxidation. A voltammetric method is proposed for the determination of nitrite, over a concentration range of three orders of magnitude (0.05 to 20 mM), with good reproducibility, high stability and excellent sensitivity. The high upper limit of the dynamic range of the analytically useful response might provide a basis for the reliable quantification of nitrite in wastewater.
This article presents a layered mixed oxide thin film composed of Sn, Ti, Zn, and Pr obtained by sol-gel deposition for gas sensing applications. The film was characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, UV-Vis spectroscopy, Scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX), and Electrochemical impedance spectroscopy (EIS). X-ray diffraction results showed the presence of a single crystalline phase with a cassiterite-like structure. Raman spectroscopy revealed characteristic bands of oxygen-deficient SnO2-based nanocrystallites. The band gap energy calculated from UV-Vis spectroscopy is Eg = 3.83 eV. The XPS proved the presence on the surface of all elements introduced by the inorganic precursors as well as their oxidation states. Thus, Sn4+, Ti4+, Zn2+, and Pr3+ were detected on the surface. Moreover, by XPS, we highlighted the presence of OH groups and water adsorbed on the surface. SEM showed the five-layer morphology of the film after five successive depositions. Electrochemical properties were determined by EIS-impedance spectroscopy. The selectivity for gas sensing was also investigated for methane, propane, and formaldehyde and the gas sensing mechanism was explained. The results indicated that the mixed oxide thin film exhibited high sensitivity and selectivity towards specific gases.
The present work reports the synthesis of efficient Ti-Au/zeolite Y photocatalysts by different processing of aluminosilicate gel and studies the effect of titania content on the structural, morphological, textural, and optical properties of the materials. The best characteristics of zeolite Y were obtained by aging the synthesis gel in static conditions and mixing the precursors under magnetic stirring. Titania (5, 10, 20%) and gold (1%) species were incorporated in zeolite Y support by the post-synthesis method. The samples were characterized by X-ray diffraction, N2-physisorption, SEM, Raman, UV-Vis and photoluminescence spectroscopy, XPS, H2-TPR, and CO2-TPD. The photocatalyst with the lowest TiO2 loading shows only metallic Au on the outermost surface layer, while a higher content favors the formation of additional species such as: cluster type Au, Au1+, and Au3+. A high TiO2 content contributes to increasing the lifetime of photogenerated charge careers, and the adsorption capacity of the pollutant. Therefore, an increase in the photocatalytic performances (evaluated in degradation of amoxicillin in water under UV and visible light) was evidenced with the titania content. The effect is more significant in visible light due to the surface plasmon resonance (SPR) effect of gold interacting with the supported titania.
The control of catalytic performance using synthesis conditions is one of the main goals of catalytic research. Two series of Pt-Ti/SBA-15 catalysts with different TiO2 percentages (n = 1, 5, 10, 30 wt.%) were obtained from tetrabutylorthotitanate (TBOT) and peroxotitanate (PT), as titania precursors and Pt impregnation. The obtained catalysts were characterized using X-ray diffraction, scanning electron microscopy (SEM) and transmission electron microscopy (TEM), N2 sorption, Raman, X-ray photoelectron spectroscopy (XPS), X-ray absorption spectroscopy (XAS), hydrogen temperature-programmed reduction (H2-TPR) and H2-chemisorption measurements. Raman spectroscopy showed framework titanium species in low TiO2 loading samples. The anatase phase was evidenced for samples with higher titania loading, obtained from TBOT, and a mixture of rutile and anatase for those synthesized by PT. The rutile phase prevails in rich TiO2 catalysts obtained from PT. Variable concentrations of Pt0 as a result of the stronger interaction of PtO with anatase and the weaker interaction with rutile were depicted using XPS. TiO2 loading and precursors influenced the concentration of Pt species, while the effect on Pt nanoparticles' size and uniform distribution on support was insignificant. The Pt/PtO ratio and their concentration on the surface were the result of strong metal-support interaction, and this influenced catalytic performance in the complete oxidation of methane at a low temperature. The highest conversion was obtained for sample prepared from PT with 30% TiO2.
Two novel graphene oxide-benzofuran derivatives composites were obtained through the covalent immobilization of [4-hydrazinyl-7nitrobenz-[2,1,3-d]-oxadiazole (NBDH) and respectively, N1-(7-nitrobenzo[c][1,2,5]oxadiazol-4-yl)benzene-1,2-diamine (NBD-PD), on graphene oxide. This covalent functionalization was achieved by activating the carboxylic groups on the surface of graphene oxide by the reaction with thionyl chloride followed by coupling with the amino group of benzofurazane derivatives to obtain the NBD derivatives grafted on graphene oxide. The formation of new materials was check by Raman spectroscopy, fluorescence, infrared spectroscopy and X-ray photoelectron spectroscopy, thermal analysis, scanning electron microscopy, and elemental mapping. The antimicrobial effect of the new composites was evaluated on Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa, both on planktonic and adherent biofilm populations. The cytotoxic effects of the materials on human colon cancer HCT-116 cell line and the normal human fibroblast BJ cell line were evaluated by investigating cell viability and membrane integrity. Apoptosis and colony forming ability of tumor cells were also investigated following exposure to new materials. The biological results of this study have shown that the new materials have potential in combating biofilm formation and also, the tested materials induced cytotoxicity in human colon cancer HCT-116 cell line with limited effects on normal BJ fibroblasts, suggesting their antitumor potential.
Graphite , Nanocomposites , Anti-Bacterial Agents/pharmacology , Benzoxazoles , Humans
Although both stable free organic radicals and biomass-derived hydrochars have emerged as appealing, green, multifunctional materials, their association has not been explored. In this study, strength is found to lie in their union, which primarily leads to stable redox-active free-radical-hydrochar composites that can generate unexpected opportunities for the development of advanced metal-free sustainable materials. The composites are obtained by a straightforward green one-pot hydrothermal procedure. The loading of stable free radicals of nitroxide type and their localization is engineered by the nature of the carbohydrate and the reaction status; vigorous reaction parameters promote faster nucleation and growth kinetics of the hydrochar products, leading to a covalent immobilization of redox species on the surface of the carbonaceous microspherical aggregates. The nitroxide free-radical-hydrochar materials demonstrate enhancements in terms of both electrocatalytic activity and capacitive features.
The paper presents the possibility of detecting low H2S concentrations using CuWO4. The applicative challenge was to obtain sensitivity, selectivity, short response time, and full recovery at a low operating temperature under in-field atmosphere, which means variable relative humidity (%RH). Three different chemical synthesis routes were used for obtaining the samples labeled as: CuW1, CuW2, and CuW3. The materials have been fully characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). While CuWO4 is the common main phase with triclinic symmetry, different native layers of CuO and Cu(OH)2 have been identified on top of the surfaces. The differences induced into their structural, morphological, and surface chemistry revealed different degrees of surface hydroxylation. Knowing the poisonous effect of H2S, the sensing properties evaluation allowed the CuW2 selection based on its specific surface recovery upon gas exposure. Simultaneous electrical resistance and work function measurements confirmed the weak influence of moisture over the sensing properties of CuW2, due to the pronounced Cu(OH)2 native surface layer, as shown by XPS investigations. Moreover, the experimental results obtained at 150 °C highlight the linear sensor signal for CuW2 in the range of 1 to 10 ppm H2S concentrations and a pronounced selectivity towards CO, CH4, NH3, SO2, and NO2. Therefore, the applicative potential deserves to be noted. The study has been completed by a theoretical approach aiming to link the experimental findings with the CuW2 intrinsic properties.
Semiconducting metal oxide-based gas sensors are an attractive option for a wide array of applications. In particular, sensors based on WO3 are promising for applications varying from indoor air quality to breath analysis. There is a great breadth of literature which examines how the sensing characteristics of WO3 can be tuned via changes in, for example, morphology or surface additives. Because of variations in measurement conditions, however, it is difficult to identify inherent qualities of WO3 from these reports. Here, the sensing behavior of five different WO3 samples is examined. The samples show good complementarity to SnO2 (the most commonly used material)-based sensors. A surprising homogeneity, despite variation in morphology and preparation method, is found. Using operando diffuse reflectance infrared Fourier transform spectroscopy, it is found that the oxygen vacancies are the dominant reaction partner of WO3 with the analyte gas. This surface chemistry is offered as an explanation for the homogeneity of WO3-based sensors.
Breath Tests , Oxides , Oxygen
In this study, the synergistic behavior of Ni species and bimodal mesoporous undoped SnO2 is investigated in oxygen evolution reactions (OERs) under alkaline conditions without any other modification of the compositional phases or using noble metals. An efficient and environmentally friendly hydrothermal method to prepare bimodal mesoporous undoped SnO2 with a very high surface area (>130 m2 g-1) and a general deposition-precipitation method for the synthesis of well-dispersed Ni species on undoped SnO2 are reported. The powders were characterized by adsorption-desorption isotherms, TG-DTA, XRD, SEM, TEM, Raman, TPR-H2, and XPS. The best NiSn composite generates, under certain experimental conditions, a very high TOF value of 1.14 s-1 and a mass activity higher than 370 A g-1, which are remarkable results considering the low amount of Ni deposited on the electrode (3.78 ng). Moreover, in 1 M NaOH electrolyte, this material produces more than 24 mA cm-2 at an overpotential value of approximately +0.33 V, with only 5 wt % Ni species. This performance stems from the dual role of undoped SnO2, on the one hand, as a support for active and well-dispersed Ni species and on the other hand as an active player through the oxygen vacancies generated upon Ni deposition.
The Ti/hierarchical zeolites Y were obtained by direct and post synthesis methods and loaded with Fe(III) by ion-exchange and impregnation resulting Fe-Ti/hierarchical zeolites Y photocatalysts. The synthesized materials were characterized by XRD, SEM microscopy, N2 physical adsorption, Raman, UV-Vis and XPS and EPR spectroscopy. XRD patterns evidenced the crystalline structure of the zeolite Y in all materials, excepting the samples with higher Fe content. The presence of anatase was evidenced by XRD and Raman spectroscopy in the samples obtained by impregnation while α-Fe2O3 was depicted in the Raman spectra of the samples with Ti and lower Fe loading. SEM images and N2 adsorption-desorption isotherms confirmed the formation of mesopores together with microporous crystals of zeolite Y. The UV-Vis spectra proved a red-shifted adsorption band for samples with iron. In all these samples XPS shows Fe3+ as oxide on the surface and EPR Fe3+ in tetrahedral coordination. Different variables such as hierarchical structure, amount of iron, catalyst loading, concentration of pollutant solution, pH value were studied to estimate their effects on performances of photocatalysts in degradation of amoxicillin from aqueous solution in UV and Visible light. A higher adsorption capacity and degradation efficiency of amoxicillin (100%) was noticed for hierarchical materials, especially for higher iron oxide loaded samples.
Zeolites , Amoxicillin , Ferric Compounds , Oxides , Titanium
Two ZnO materials of spherical hierarchical morphologies, with hollow (ZnOHS) and solid cores (ZnOSS), were obtained through the hydrolysis of zinc acetylacetonate in 1,4-butanediol. The nature of the defects and surface reactivity for the two ZnO materials were investigated through photoluminescence, X-ray photoelectron spectroscopy, and electron paramagnetic resonance (EPR) spectroscopy proving the coexistence of shallow and deep defects and, also, the presence of polyol byproducts adsorbed on the outer layers of the ZnO samples. The EPR spectroscopy coupled with the spin-trapping technique showed that the surface of the ZnO samples generates reactive oxygen species (ROS) like hydroxyl (â¢OH) and singlet oxygen (1O2) as well as carbon-centered radicals. The ZnO materials exhibited a wide spectrum of antimicrobial activity, being active against Gram-positive, Gram-negative, and fungi strains, both in planktonic and, more importantly, adherent growth states. The decrease of antimicrobial efficiency in the presence of a ROS scavenger (mannitol) and the decrease of the cell viability with the ROS level suggest that one of the mechanisms that governs both the antimicrobial and cytotoxic activities on human liver cells is ROS-mediated. However, at active antimicrobial concentrations, the biocompatibility of the tested materials is very good.
Anti-Bacterial Agents/pharmacology , Nanostructures/chemistry , Zinc Oxide/pharmacology , Anti-Bacterial Agents/chemical synthesis , Anti-Bacterial Agents/chemistry , Anti-Bacterial Agents/toxicity , Candida albicans/drug effects , Cryptococcus neoformans/drug effects , Gram-Negative Bacteria/drug effects , Gram-Positive Bacteria/drug effects , Hep G2 Cells , Humans , Hydroxybutyrates/chemistry , Hydroxyl Radical/chemical synthesis , Microbial Sensitivity Tests , Nanostructures/toxicity , Pentanones/chemistry , Singlet Oxygen/chemistry , Zinc Oxide/chemical synthesis , Zinc Oxide/chemistry , Zinc Oxide/toxicity
NiFe2 O4 -Ce0.8 Gd0.2 O2-δ (NFO/CGO) nanocomposite thin films were prepared by simultaneously radio-frequency (RF) magnetron sputtering of both NFO and CGO targets. The aim is the growth of a CO2 -stable composite layer that combines the electronic and ionic conduction of the separate NFO and the CGO phases for oxygen separation. The effect of the deposition temperature on the microstructure of the film was studied to obtain high-quality composite thin films. The ratio of both phases was changed by applying different power to each ceramic target. The amount of each deposited phase as well as the different oxidation states of the nanocomposite constituents were analyzed by means of X-ray photoelectron spectroscopy (XPS). The transport properties were studied by conductivity measurements as a function of temperature and pO2 . These analyses enabled (1)â selection of the best deposition temperature (400 °C), (2)â correlation of the p-type electronic behavior of the NFO phase with the hole hopping between Ni3+ -Ni2+ , and (3)â following the conductivity behavior of the grown composite layer (prevailing ionic or electronic character) attained by varying the amount of each phase. The sputtered layer exhibited high ambipolar conduction and surfaceexchange activity. A 150â nm-thick nanograined thin film was deposited on a 20â µm-thick Ba0.5 Sr0.5 Co0.8 Fe0.2 O3-δ asymmetric membrane, resulting in up to 3.8â mL min-1 cm-2 O2 permeation at 1000 °C under CO2 atmosphere.
The challenge for conformal modification of the ultra-high internal surface of nanoporous silicon was tackled by electrochemical polymerisation of 2,6-dihydroxynaphthalene using cyclic voltammetry or potentiometry and, notably, after the thermal treatment (800 °C, N2, 4 h) an assembly of interconnected networks of graphene strongly adhering to nanoporous silicon matrix resulted. Herein we demonstrate the achievement of an easy scalable technology for solid state supercapacitors on silicon, with excellent electrochemical properties. Accordingly, our symmetric supercapacitors (SSC) showed remarkable performance characteristics, comparable to many of the best high-power and/or high-energy carbon-based supercapacitors, their figures of merit matching under battery-like supercapacitor behaviour. Furthermore, the devices displayed high specific capacity values along with enhanced capacity retention even at ultra-high rates for voltage sweep, 5 V/s, or discharge current density, 100 A/g, respectively. The cycling stability tests performed at relatively high discharge current density of 10 A/g indicated good capacity retention, with a superior performance demonstrated for the electrodes obtained under cyclic voltammetry approach, which may be ascribed on the one hand to a better coverage of the porous silicon substrate and, on the other hand, to an improved resilience of the hybrid electrode to pore clogging.
A novel nanocomposite was obtained through the covalent immobilization of lipoic acid on the surface of silver nanoparticles-decorated silica nanoparticles (SiO2@Ag). The hybrid organic - inorganic material obtained was characterized by Fourier transform infrared spectroscopy, thermal analysis, scanning and transmision electron microscopy, X-ray photoelectron spectroscopy and UV-Visible spectroscopy. Its antioxidant, cytotoxic, antimicrobial activity and influence on mammalian cells cycle were evaluated. The results of this study have shown that the functionalization of SiO2@Ag with lipoic acid resulted in a composite with increased specificity of interaction with different mammalian cell lines and antioxidant activity, but with decreased cytotoxicity and antimicrobial properties. Therefore, the SiO2@Ag functionalized with lipoic acid could be successfully used in certain concentrations to modulate the cell cycle, in order to obtain the desired anti-proliferative or stimulatory therapeutic effect.
Metal Nanoparticles , Animals , Humans , Nanocomposites , Silicon Dioxide , Silver , Spectroscopy, Fourier Transform Infrared , Thioctic Acid
Development of new sensitive materials by different synthesis routes in order to emphasize the sensing properties for hazardous H2S detection is one of a nowadays challenge in the field of gas sensors. In this study we obtained mesoporous SnO2-CuWO4 with selective sensitivity to H2S by an inexpensive synthesis route with low environmental pollution level, using tripropylamine (TPA) as template and polyvinylpyrrolidone (PVP) as dispersant/stabilizer. In order to bring insights about the intrinsic properties, the powders were characterized by means of a variety of complementary techniques such as: X-Ray Diffraction, XRD; Transmission Electron Microscopy, TEM; High Resolution TEM, HRTEM; Raman Spectroscopy, RS; Porosity Analysis by N2 adsorption/desorption, BET; Scanning Electron Microscopy, SEM and X-ray Photoelectron Spectroscopy, XPS. The sensors were fabricated by powders deposition via screen-printing technique onto planar commercial Al2O3 substrates. The sensor signals towards H2S exposure at low operating temperature (100°C) reaches values from 105 (for SnWCu600) to 106 (for SnWCu800) over the full range of concentrations (5-30ppm). The recovery processes were induced by a short temperature trigger of 500°C. The selective sensitivity was underlined with respect to the H2S, relative to other potential pollutants and relative humidity (10-70% RH).
ZnO-carbon composite spheres were synthesized via starch hydrothermal carbonization (HTC) in the presence of a soluble zinc salt (acetate), followed by thermal processing under an argon atmosphere. Besides sustainability, the one-pot procedure represents a scalable synthesis of tailored carbon-metal oxide spheres with a structurally-ordered carbon matrix obtained at a relatively low temperature (700 °C). The ability of zinc cations to develop different linkages with starch's hydrophilic functional groups and to act as external nucleators determines an increase in HTC yield; the effect is obvious even in the presence of small concentrations of zinc in the reaction medium (0.005 M), thus providing a way to improve the carbonization process efficiency. It is also shown that zinc content is the control vector of the spherical composite's properties: a variation from 0.3 to 4.8 at% not only induces a variation in their size (200 nm-10 µm), interconnectivity (from disperse spheres to necklace-like aggregations), surface area and connected porosity (from micro- to mesoporosity), but also of their electrochemical and white light adsorption and emission features. Since the variation in zinc content is made by a simple adjustment of the raw material concentrations, the functionality of these carbon-based materials can be modulated in a straightforward manner.
A starch-assisted synthetic methodology of multispheres ZnO-starch biocomposites was developed. An additional thermal processing of the ZnO-starch composites induces the formation of ZnO with donut-like morphology. The synthesis of single-phase zinc oxide with a spherical morphology is conditioned by the presence of starch, which acts as template, stabilizing/capping agent. The synthesized structures present significant photocatalytic activities; a total phenol mineralization is attained with the donut-like ZnO photocatalyst under visible light irradiation, due to a cumulative effect of the its relatively large specific surface area, high crystallinity and favorable combination of defects for band narrowing, which together permit an enhanced utilization rate of the light.
Starch/chemistry , Zinc Oxide/chemistry , Zinc Oxide/chemical synthesis , Catalysis , Chemistry Techniques, Synthetic , Photochemical Processes
Mesoporous metal oxides (CeO(2-δ))-YSZ have been synthesized by a versatile direct synthesis method using ionic cetyltrimethylammonium bromide (CTAB) and different nonionic (block copolymers) as surfactants and urea as hydrolyzing agent. The synthesis was realized at pH=9 using tetraethylammonium hydroxide (TEAOH) as pH mediator. Calcination at 550 °C led to the formation of crystalline metal oxides with uniform mesoporosity. The obtained materials have been characterized by thermogravimetric analysis (TG-DTG), wide and small-angle X-ray diffraction (XRD), Raman spectroscopy, Brunauer, Emmett and Teller (BET) surface area analysis, scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). All the obtained materials exhibits mesoporous structure, crystalline structure indexed in a cubic symmetry, showing a high surface area, a uniform and narrow pore size distribution, spherical morphology typical for the mesoporous materials. The crystalline and mesoporous structures, surface chemistry and stoichiometry for the samples synthesized using ionic and nonionic surfactants have been discussed.
