RESUMEN
The potential use of activated carbon (AC) as an inexpensive and effective alternative sorbent material in thermal desorption is presented and validated for the analysis of aromatic volatile organic compounds (VOCs) such as benzene, toluene, m-xylene, and styrene (BTXS) in air. The optimum desorption conditions of an AC sampling tube (2 mg AC bed) were determined and compared with a commercial three-bed (Carbopack; C + B + X) tube sampler as a reference. The AC sampler exhibited good linearity (R2â¯>â¯0.99) and reproducibility (RSE of 2.38⯱â¯0.21%) for BTXS analysis. The AC tube sampler showed good storability (up to 3â¯d) and excellent recyclability (up to 50 cycles). An analysis of BTXS in ambient air showed excellent agreement between AC and CBX (biasâ¯<â¯5%). The 1% breakthrough volume values for 2â¯mg AC, when tested at 100â¯ppb of benzene as a sole component or in a BTXS mixture, were 10,000 or 5000â¯Lâ¯g-1, respectively. The results of this study support the performance of AC as a suitable medium for sampling VOCs as reliable as high-cost commercial sorbent products.
Asunto(s)
Contaminantes Atmosféricos , Carbón Orgánico , Compuestos Orgánicos Volátiles , Benceno , Reproducibilidad de los ResultadosRESUMEN
Covalent-organic polymers (COPs) are recognized for their great potential for treating diverse pollutants via adsorption. In this study, the sorption behavior of benzene and toluene was investigated both individually and in a binary mixture against two types of COPs possessing different -NH2 functionalities. Namely, the potential of COPs was tested against benzene and toluene in a low inlet partial pressure range (0.5-20â¯Pa) using carbonyl-incorporated aromatic polymer (CBAP)-1-based diethylenediamine (EDA) [CD] and ethylenetriamine (DETA) [CE]. The maximum adsorption capacity and breakthrough values of both COPs showed dynamic changes with increases in the partial pressures of benzene and toluene. The maximum adsorption capacities (Amax) of benzene (as the sole component in N2 under atmospheric conditions) on CD and CE were in the range of 24-36 and 33-75â¯mgâ¯g-1, respectively. In contrast, with benzene and toluene in a binary mixture, the benzene Amax decreased more than two-fold (range of 2.7-15 and 6-39â¯mgâ¯g-1, respectively) due to competition with toluene for sorption sites. In contrast, the toluene Amax values remained consistent, reflecting its competitive dominance over benzene. The adsorption behavior of the targeted compounds (i.e., benzene and toluene) was explained by fitting the adsorption data by diverse isotherm models (e.g., Langmuir, Freundlich, Elovich, and Dubinin-Radushkevich). The current research would be helpful for acquiring a better understanding of the factors affecting competitive adsorption between different VOCs in relation to a given sorbent and across varying partial pressures.
Asunto(s)
Gases , Hidrocarburos/química , Nanoporos , Polímeros , Adsorción , Benceno , Presión Parcial , ToluenoRESUMEN
This study investigated the emission characteristics of glass particles resulting from smoking electronic cigarettes (ECs). First, the most suitable filter for the collection of glass particles was explored by examining the performance (reliability) of various types of filters. A polycarbonate filter was determined as the optimum choice to collect glass particles in EC aerosol. A cartomizer was filled with EC refill solution composed of an equal volume of propylene glycol (PG) and vegetable glycol (VG). To simulate the potential conditions for glass particle emission, EC vaped aerosols were collected at three distinctive puffing intervals: (1) 0-10 puffs, (2) 101-110 puffs, and (3) 201-210 puffs (flow rate of 1â¯Lâ¯min-1, 2â¯s per puff, and 10 puffs per sample). Glass particles were observed as early as after 100 times puffing from certain products, while after 200 from others. Thus, glass particles were generated by increasing the number of puffs and usage of the EC cartomizer. The analysis of glass particles collected onto polycarbonate filters by scanning electron microscopy (SEM)/energy dispersive X-ray spectroscopy (EDS) confirmed the presence of glass particles in samples collected after puffing 100-200â¯times. The study demonstrated that the possibility of glass particle emissions from the EC device increased considerably with the increasing number of total puffs.
Asunto(s)
Contaminantes Atmosféricos/análisis , Sistemas Electrónicos de Liberación de Nicotina , Vidrio/análisis , Vapeo , Aerosoles/análisis , Reproducibilidad de los ResultadosRESUMEN
In this study, the analytical bias in the measurements of reduced sulfur compounds (RSC) was investigated in terms of sorptive loss caused by the materials selected for the sample introduction. For the purpose of this study, three vacuum samplers made in the combination of different vacuuming efficiencies (e.g., rapid versus slow sampling) and different materials (i.e., Teflon versus stainless steel (SS)) were tested to evaluate the sampling recovery rate (RR) for five RSCs: H(2)S, CH(3)SH, DMS, CS(2) and DMDS. To make a parallel comparison of RR, the RSC standard samples contained in one bag were transferred to another bag using each sampling system. Their relative contents between, before, and after the transfer were then evaluated between different samplers to assess the sampling bias caused by the interaction between RSC and the sampling material. In the case of the most reactive compound, H(2)S, the sampling loss from the SS inlet line amounted to as high as 45%, while that for the Teflon counterpart was almost insignificant. When the sampling time was arbitrarily elongated (i.e., use of a slow sampler), the sampling loss rate of the SS inlet sampler became more significant with the RR values dropping down from 55 to 70%, across different RSCs. The overall results of our comparative study indicate that the sampling system for the reactive gaseous compounds should be checked for the material feasibility to guarantee sufficient analytical reliability.