First Report of Leaf Rot Caused by Apiospora paraphaeosperma on Lily in Wuhan, China.

Lily (Lilium spp.) is a valuable ornamental bulb flower plant in Liliaceae, and its bulbs have high edible and medicinal value. Compared with bulb propagation of other lilies, seed propagation and short growth period are the most significant characteristics of Lilium×formolongi. In 2023, leaf rot disease (LRD) was observed on approximately 70% of the Lilium×formolongi seedlings sown in an experimental greenhouse in Wuhan, Hubei province, China. Irregular brown water-soaked spots were discovered in the early stages of infected seedlings. Then, spots spread throughout the leaves and caused the leaves to brown, soften, and wilted. A pathogen associated with symptoms was isolated by incubating sterilized leaves on potato dextrose agar plates at 25 ℃ for 2-3 days. Then, a pure single colony was isolated through a single hyphal tip isolation method. The fungal colony was white with abundant aerial mycelium and produced a yellow pigment diffusible into the agar. Microscopically, isolated mycelia were reticulate and pale yellow, while conidia were dark brown, smooth, and spherical, 7.31 to 6.98 × 4.03 to 3.87µm (average 5.44×5.41µm; n=30); oval in lateral view, and had a light stripe in the middle. To identify the species of the fungus at the molecular level, ITS and EF-1α genes were amplified and sequenced using primers ITS1/ITS4 (M Gardes et al. 1993) and 758F/986R (Carbone and Kohn 1999). The BLAST results in GenBank showed that the ITS(OR523578) and EF-1α(PP066842) sequences of LRD shared 99.82% and 99.24% identity with the distinct Apiospora paraphaeosperma strains (GenBank accession MT040110, ON806628.1, respectively). Combined with the morphology of the colony and conidium, the fungus was identified as Ap. paraphaeosperma. In the pathogenicity test, six healthy leaves were inoculated with mycelium disc and then kept in an incubator (22 ℃, 90% humidity, 16h light /8h darkness). The inoculated leaves showed necrosis and wilt symptoms similar to those observed in the greenhouse, while the control leaves were asymptomatic. A re-isolation, morphology identification and DNA sequencing of the fungus confirmed its infection with Ap. paraphaeosperma in Lilium spp. At present, rot caused by Ap. paraphaeosperma has only been reported in Thailand and South Korea, both of which are found on bamboo stems (Hyde et al. 2016; Sun Lul Kwon et al. 2022). As far as we know, this is the first report of leaf rot of lily caused by Ap. paraphaeosperma in China. This report can help identify this disease and further develop effective control measures.

Flexible and ultrasensitive piezoresistive electronic skin based on chitin/sulfonated carbon nanotube films.

Wearable electronic skin has gained increasing popularity due to its remarkable properties of high flexibility, sensitivity, and lightweight, making it an ideal choice for detecting human physiological activity. In this study, we successfully prepared e-skin using regenerated chitin (RCH) and sulfonated carbon nanotubes (SCNTs). The e-skin demonstrated brilliant mechanical and sensing properties, exhibiting a sensitivity of 1.75 kPa-1 within the 0-5 kPa range and a fast response-recovery time of <10 ms. Furthermore, it displayed an ultra-low detection limit of 1.39 Pa (5 mg), exceptional stability (up to 11,000 cycles), and a remarkable mechanical strength, reaching up to 50 MPa. Moreover, the e-skin was fabricated through a simple and economical approach. With the popularity of micro sensing devices, the e-skin holds tremendous potential for various applications, including wearable electronic devices, health and sports monitoring, artificial intelligence and other fields.

Mitigation the release of toxic PH3 and the fire hazard of PA6/AHP composite by MOFs.

Aluminum hypophosphite (AHP) is a high-efficiency phosphorus-based flame retardant with high P content, which is widely used in Polyamide 6 (PA6). However, AHP releases phosphine gas (PH3) at high temperatures, which is highly toxic to human's health and environment. Metal-organic frameworks (MOFs) have porous structure exhibiting high performance in gas adsorption. Therefore, mesoporous iron (III) carboxylate [MIL-100 (Fe)] was synthesized in this work and employed to study the adsorption capacity of toxic PH3 in PA6/AHP composite during processing. AHP was combined with melamine cyanurate (MCA) and MIL-100 (Fe) followed by blending with PA6 to prepare PA6 composites (PA6/MA and PA6/MAF). PA6/MAF with the weight ratio of 5:5 performed well in inhibiting the release of PH3 during the processing of composite as well as the accelerated thermal experiment devised by our group. Besides, PA6/MAF (5:5) showed relatively low fire hazard reflected by the reduction of the peak of heat release rate of PA6 composite from 962 to 260 kW/m2 compared with that of pure PA6 in the cone calorimeter test, and MIL-100 (Fe) along with MCA also presented synergistic effect in suppressing the emission of carbon monoxide. The subtle selection of MOFs herein has the potential to be used as a promising synergist for hazardous gases released from polymer composites to improve the occupational and fire safety in the society.