RESUMEN
End functionalized polylactides are prepared by ring opening polymerization of L-lactide in the presence of stannous octoate (Sn(Oct)2). Three chromophores, 9H-carbazol-ethanol (CA), 9-fluorenyl-methanol (FM), and 2-(4-(2-chloro-4-nitrophenylazo)-N-ethylphenylamino)ethanol (Disperse Red 13, DR), are for the first time used as co-initiators in the polymerization process. The polymerization reaction is initiated by conventional thermal treatment, but in the case of FM, microwave-assisted polymerization is also carried out. CA and FM absorb and emit in the UV portion of the electromagnetic spectrum, whereas DR absorbs in the visible part. The obtained end-capped polylactides derivatives show the same photophysical properties as the initiator, so they are "macromolecular dyes" (MDs) that can be used "as synthesized" or can be blended with commercial poly(lactic acid) (PLA). The blends of PLA with MDs have ultraviolet-visible (UV-Vis) absorption and fluorescence emission features similar to that of MDs and thermal properties typical of PLA. Finally, migration tests, carried out onto the blends of PLA with MDs and PLA with free chromophores, show that MDs are less released than free chromophores both in solution and in the solid phase.
RESUMEN
The behavior of NaBH4 (THB) and the amine boranes, NH3BH3 (AB), tertbutylNH2BH3 (TBAB), Me2NHBH3 (DMAB) was investigated in continuous flow chemical vapor generation of H2Se from aqueous SeIV coupled with atomic absorption spectrometry. Unexpected higher efficiency of H2Se generation was obtained with amine boranes compared to THB (TBAB > AB > THB) using millimolar concentration of reductant (0.001-0.1 mol L-1) under strongly acidic conditions (HCl, HClO4, H2SO4, HNO3, 0.5-5 mol L-1 H+). Analytical applicability of the CVG system was tested by the determination of SeIV in natural water samples certified reference materials, using 0.01 mol L-1 TBAB in 0.5 M H2SO4. In order to explain this unexpected higher efficiency of amine boranes with respect of THB, the kinetic of hydrolysis of AB, TBAB and DMAB was investigated in acid media typically employed in chemical vapor generation for trace element determination. The kinetic was investigated by monitoring the rate the hydrogen gas evolved during hydrolysis, using a laboratory made thermostated reaction cell. Kinetics were measured for AB, TBAB and DMAB in 0.1, 0.5, 5 mol L-1 HCl or HClO4 reaction media and in 0.1 mol L-1 cysteine +0.1 mol L-1 HCl or HClO4 buffer, for reaction times from 0 to 30 min. Under strongly acidic conditions, the rates of hydrogen evolution produced by amine boranes hydrolysis appear to be much slower than those predicted by a pseudo-first order reaction and using the rate constants reported in the literature. This suggests that, at elevated acidities (5 mol L-1 HCl or HClO4), the hydrolysis of amine boranes takes place in two steps, generating a first amount of H2 (0.67-1.15 mol) much faster than the remaining about 2 mol. This evidence indicates a different mechanism of hydrolysis to the one accepted in the literature for amine boranes. The relatively high efficiencies of H2Se observed with amine borane reduction of inorganic SeIV at elevated acidities can be addressed to the action of borane intermediates, most probably amine borane cations, formed during amine borane hydrolysis in the same reaction conditions.
RESUMEN
The data reported in this paper are complementary to the characterization of 4-(phenylazo)-benzoyl-2,2,6,6-tetramethylpiperidine-1-oxyl radical (AzO-TEMPO) and of the 4-(2-thienylazo)-benzoyl-2,2,6,6-tetramethylpiperidine-1-oxyl radical (ThiO-TEMPO) before and after their grafting to two polyethylene matrices (a copolymer ethylene/α-olefin (co-EO) and a high density polyethylene (HDPE)). Particularly the data reported in this paper confirm the structure (FT-IR analysis), the thermal (TGA and EPR) and the photo-physical (UV-vis) properties of the RO-TEMPO derivatives before and after their grafting. Herein, the FT-IR spectrum and TGA thermogram of ThiO-TEMPO were compared with those of AzO-TEMPO. Moreover, the superimposition of UV-vis spectra collected during the irradiation under 366 or 254 nm emitting lamp of AzO-TEMPO and ThiO-TEMPO in acetonitrile solution are reported. Finally, a complete DSC characterization of the functionalized POs is shown. DOI of original article: ãhttp://dx.doi.org/10.1016/j.polymer.2015.11.018ã [1].
RESUMEN
Multidimensional analysis of instant coffee and barley beverage samples using size exclusion chromatography (SEC) combined with a dynamic surface tension detector (DSTD) and a UV-vis absorbance detector (UV) is reported. A unique finding of this study was the action of the tetrabutylammonium (TBA) cation as a modifying agent (with bromide as the counter anion) that substantially increased the surface pressure signal and sensitivity of many of the proteins in the chromatographically separated samples. The tetrabutylammonium bromide (TBAB) enhancement of the surface pressure signal was further investigated by studying the response of 12 commercial standard proteins (alpha-lactalbumin, beta-lactoglobulin, human serum albumin (HSA), albumin from chicken egg white (OVA), bovine serum albumin (BSA), hemoglobin, alpha-chymotrypsinogen A, cytochrome C, myoglobin, RNase A, carbonic anhydrase, and lysozyme) in buffer performed using flow injection analysis (FIA) coupled with the DSTD with and without various concentrations of TBAB. The FIA-DSTD data show that 1mM TBAB enhances sensitivity of HSA detection, by lowering the limit of detection (LOD) from 2mg/mL to 0.1mg/mL. Similarly, the LOD for BSA was reduced from 1mg/mL to 0.2mg/mL. These FIA-DSTD experiments allowed the detection conditions to be optimized for further SEC-UV/DSTD experiments. Thus, the SEC-UV/DSTD system has been optimized and successfully applied to the selective analysis of surface-active protein fractions in a commercial instant coffee sample and in a soluble barley sample. The complementary selectivity of using the DSTD relative to an absorbance detector is also demonstrated.
