Biocompatible Ionic Liquids in High-Performing Organic Electrochemical Transistors for Ion Detection and Electrophysiological Monitoring.

Organic electrochemical transistors (OECTs) have recently attracted attention due to their high transconductance and low operating voltage, which makes them ideal for a wide range of biosensing applications. Poly-3,4-ethylenedioxythiophene:poly-4-styrenesulfonate (PEDOT:PSS) is a typical material used as the active channel layer in OECTs. Pristine PEDOT:PSS has poor electrical conductivity, and additives are typically introduced to improve its conductivity and OECT performance. However, these additives are mostly either toxic or not proven to be biocompatible. Herein, a biocompatible ionic liquid [MTEOA][MeOSO3] is demonstrated to be an effective additive to enhance the performance of PEDOT:PSS-based OECTs. The influence of [MTEOA][MeOSO3] on the conductivity, morphology, and redox process of PEDOT:PSS is investigated. The PEDOT:PSS/[MTEOA][MeOSO3]-based OECT exhibits high transconductance (22.3 ± 4.5 mS µm-1), high µC* (the product of mobility µ and volumetric capacitance C*) (283.80 ± 29.66 F cm-1 V-1 s-1), fast response time (∼40.57 µs), and excellent switching cyclical stability. Next, the integration of sodium (Na+) and potassium (K+) ion-selective membranes with the OECTs is demonstrated, enabling selective ion detection in the physiological range. In addition, flexible OECTs are designed for electrocardiography (ECG) signal acquisition. These OECTs have shown robust performance against physical deformation and successfully recorded high-quality ECG signals.

Crown ether enabled enhancement of ionic-electronic properties of PEDOT:PSS.

Poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) based organic electrochemical transistors (OECTs) have proven to be one of the most versatile platforms for various applications including bioelectronics, neuromorphic computing and soft robotics. The use of PEDOT:PSS for OECTs originates from its ample mixed ionic-electronic conductivity, which in turn depends on the microscale phase separation and morphology of the polymer. Thus, modulation of the microstructure of PEDOT:PSS film enables us to tune the operation and device characteristics of the resulting OECT. Herein we report enhanced transconductance (20 mS), fast switching (32 µs) and stable operation (10 000 cycles) of modified PEDOT:PSS based OECTs using 15-crown-5 as an additive. Four probe measurements reveal an increased electronic conductivity of the modified PEDOT:PSS film (∼450 S cm-1) while tapping mode atomic force microscopy shows an increased phase separation. Further detailed characterization using spectroelectrochemistry, X-ray photoelectron spectroscopy (XPS) and grazing incidence wide-angle X-ray diffraction (GIWAXS) provides insight into the microstructural changes brought about by the crown ether additive that result in the desirable characteristics of the modified PEDOT:PSS film.

Influence of solvents on the morphology of Langmuir and Langmuir-Schaefer films of PCBM and PCBM-based oligomers and polymers.

Fullerene-based polymers and oligomers combined with non-fullerene acceptors show extremely high efficiencies in organic photovoltaic devices. Furthermore, fullerene-based materials are of interest for use in anti-cancer and anti-viral treatments, where their presence can enhance the efficacy of medication considerably. Therefore, it remains important to understand their morphology and electronic properties to improve devices and technological applications. The main goal of this study is to prepare and characterize Langmuir and Langmuir-Schaefer films of PCBM-based materials to investigate the influence of different solvents such as chloroform, toluene, and xylene, and co-components on their morphology. PCBM-based materials were thus studied either alone or in mixtures with a polythiophene derivative (poly(3-hexythiophene), P3HT) commonly used in organic photovoltaic devices. The formation of Langmuir films was studied using surface pressure isotherms and Brewster's angle microscopy (BAM), where the homogeneity, phase behavior, and morphology of the films were investigated. In addition, Langmuir-Schaefer films were characterized by UV-visible absorption spectroscopy, atomic force microscopy (AFM), and Raman spectroscopy, providing information on the morphology of the solid films. This study has shown that it is possible to successfully fabricate Langmuir and Langmuir-Schaefer films of PCBM and PCBM-based oligomers and polymers, both pure and in mixtures with P3HT, to compare their organization, roughness, and optical properties. With the Langmuir films, it was possible to estimate the area of the molecules and visualize their aggregation through BAM images, establishing a relationship between the area occupied by these materials and the solvent used. All characterization techniques corroborate that the use of chloroform significantly reduced the roughness of the LS films mixed with P3HT and also presented a higher ordering compared to films prepared with xylene solutions.

A Highly Conducting Polymer for Self-Healable, Printable, and Stretchable Organic Electrochemical Transistor Arrays and Near Hysteresis-Free Soft Tactile Sensors.

A stretchable and self-healable conductive material with high conductivity is critical to high-performance wearable electronics and integrated devices for applications where large mechanical deformation is involved. While there has been great progress in developing stretchable and self-healable conducting materials, it remains challenging to concurrently maintain and recover such functionalities before and after healing. Here, a highly stretchable and autonomic self-healable conducting film consisting of a conducting polymer (poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate), PEDOT:PSS) and a soft-polymer (poly(2-acrylamido-2-methyl-1-propanesulfonic acid), PAAMPSA) is reported. The optimal film exhibits outstanding stretchability as high as 630% and high electrical conductivity of 320 S cm-1 , while possessing the ability to repair both mechanical and electrical breakdowns when undergoing severe damage at ambient conditions. This polymer composite film is further utilized in a tactile sensor, which exhibits good pressure sensitivity of 164.5 kPa-1 , near hysteresis-free, an ultrafast response time of 19 ms, and excellent endurance over 1500 consecutive presses. Additionally, an integrated 5 × 4 stretchable and self-healable organic electrochemical transistor (OECT) array with great device performance is successfully demonstrated. The developed stretchable and autonomic self-healable conducting film significantly increases the practicality and shelf life of wearable electronics, which in turn, reduces maintenance costs and build-up of electronic waste.

Pyrrolo[3,2-b]pyrrole-1,4-dione (IsoDPP) End Capped with Napthalimide or Phthalimide: Novel Small Molecular Acceptors for Organic Solar Cells.

We introduce two novel solution-processable electron acceptors based on an isomeric core of the much explored diketopyrrolopyrrole (DPP) moiety, namely pyrrolo[3,2-b]pyrrole-1,4-dione (IsoDPP). The newly designed and synthesized compounds, 6,6'-[(1,4-bis{4-decylphenyl}-2,5-dioxo-1,2,4,5-tetrahydropyrrolo[3,2-b]pyrrole-3,6-diyl)bis(thiophene-5,2-diyl)]bis[2-(2-butyloctyl)-1H-benzo[de]isoquinoline-1,3(2H)-dione] (NAI-IsoDPP-NAI) and 5,5'-[(1,4-bis{4-decylphenyl}-2,5-dioxo-1,2,4,5-tetrahydropyrrolo[3,2-b]pyrrole-3,6-diyl)bis(thiophene-5,2-diyl)]bis[2-(2-butyloctyl)isoindoline-1,3-dione] (PI-IsoDPP-PI) have been synthesized via Suzuki couplings using IsoDPP as a central building block and napthalimide or phthalimide as end-capping groups. The materials both exhibit good solubility in a wide range of organic solvents including chloroform (CF), dichloromethane (DCM), and tetrahydrofuran (THF), and have a high thermal stability. The new materials absorb in the wavelength range of 300-600 nm and both compounds have similar electron affinities, with the electron affinities that are compatible with their use as acceptors in donor-acceptor bulk heterojunction (BHJ) organic solar cells. BHJ devices comprising the NAI-IsoDPP-NAI acceptor with poly(3-n-hexylthiophene) (P3HT) as the donor were found to have a better performance than the PI-IsoDPP-PI containing cells, with the best device having a VOC of 0.92 V, a JSC of 1.7 mAcm-2, a FF of 63%, and a PCE of 0.97%.

Sterically controlled azomethine ylide cycloaddition polymerization of phenyl-C61-butyric acid methyl ester.

Phenyl-C61-butyric acid methyl ester (PCBM) is polymerized simply using a one-pot reaction to yield soluble, high molecular weight polymers. The sterically controlled azomethine ylide cycloaddition polymerization (SACAP) is demonstrated to be highly adaptable and yields polymers with probable Mn≈ 24 600 g mol(-1) and Mw≈ 73 800 g mol(-1). Products are metal-free and of possible benefit to organic and hybrid photovoltaics and electronics as they form thin films from solution and have raised LUMOs. The promising electronic properties of this new polymer are discussed.