Comparative investigation of known and unknown disinfection by-product precursor removal and microbial community from biological biochar and activated carbon filters.

Biological activated carbon filter (BAC) is one of the most effective technologies for removing disinfection by-product (DBP) precursors from water. Biochar is a lower-cost medium that has the potential to replace granular activated carbon in BAC applications, thus leading to the development of biological biochar filter (BCF). This study compared BCF with BAC for the removal of DBP precursors using column experiments. Both BCF and BAC achieved the removal of DBP precursors, resulting in concentrations of all DBP formation potential below the World Health Organization guideline values for drinking water. Bromodichloromethane and unknown DBP precursor removal by BCF was comparable to that by BAC. However, BAC removed more chloroform and dichloroacetontrile precursors than BCF. For microbial community analysis, cell numbers in a bottom layer (inlet) of BCF and BAC columns were higher than those in the top layer. The abundances of Nordella and a microbial genus from Burkholderiaceae at the bottom layer showed a strong correlation to the number of DBP precursors removed and were comparable in BCF and BAC. This finding likely contributes to the similarities between DBPs species removed and the removal performances of some known and unknown DBP precursors by BCF and BAC. Overall results from this study revealed that biochar can be served as a low-cost and sustainable replacement of activated carbon in water filter for DBP precursor removal.

Integrated remediation and detoxification of triclocarban-contaminated water using waste-derived biochar-immobilized cells by long-term column experiments.

Triclocarban (TCC), an antibacterial agent commonly used in personal care products, is one of the top ten contaminants of emerging concern in various environmental media, including soil and contaminated water in vadose zone. This study aimed to investigate TCC-contaminated water remediation using biochar-immobilized bacterial cells. Pseudomonas fluorescens strain MC46 (MC46), an efficient TCC-degrading isolate, was chosen, whereas agro-industrial carbonized waste as biochar was directly used as a sustainable cell immobilization carrier. According to the long-term TCC removal performance results (160 d), the biochar-immobilized cells consistently exhibited high TCC removal efficiencies (84-97%), whereas the free MC46 removed TCC for 76-94%. At 100 days, the detachment of the MC46 cells from the immobilized cell column was observed. The micro-Fourier-transform infrared spectroscopy results indicated that extracellular polymeric substance (EPS) was produced, but polysaccharide and protein fractions were washed out of the column. The lipid fraction of EPS adhered to the biochar, promoting TCC sorption for long-term treatment. The shortening of MC46 cells improved the tolerance of TCC toxicity. The TCC-contaminated water was successfully detoxified by the biochar-immobilized MC46 cells. Overall, the waste-derived biochar-immobilized cell system proposed in this study for the removal of emerging contaminants, including TCC, is efficient, economical, and aligned with the sustainable development concept of value-added utilization of waste.

Enhanced microwave assisted pyrolysis of waste rice straw through lipid extraction with supercritical carbon dioxide.

A combination of supercritical carbon dioxide (scCO2) extraction and microwave-assisted pyrolysis (MAP) have been investigated for the valorisation of waste rice straw. ScCO2 extraction of rice straw led to a 0.7% dry weight yield of lipophilic molecules, at elevated temperatures of 65 °C and pressures of 400 bar. Lipid compositions (fatty acids, fatty alcohol, fatty aldehydes, steroid ketones, phytosterols, n-alkanes and wax esters) of the waxes obtained by scCO2 were comparable to those obtained Soxhlet extraction using the potentially toxic solvent n-hexane. ScCO2 extraction positively influenced the pyrolysis heating rate, with a rate of 420 K min-1 for particles of 500-2000 µm, compared to 240 K min-1 for the same particle size of untreated straw. Particle size significantly affected cellulose decomposition and the distribution of pyrolysis products (gaseous, liquid and char), highlighting the importance of selecting an adequate physical pre-treatment. TG and DTG of the original rice straw and resulting biochar produced indicated that cellulose was completely decomposed during the MAP. While a rapid pressure change occurred at ∼120 °C (size > 2000 µm) and ∼130 °C (size 500-2000 µm) during MAP and was associated with the production of incondensable gas during cellulose decomposition, this takes place at significantly lower temperatures than those observed with conventional pyrolysis, 320 °C. Wax removal by scCO2 influences the dielectric properties of the straw, enhancing microwave absorption with rapid heating rates and elevated final pyrolysis temperatures, illustrating the benefits of combining these sustainable technologies within a holistic rice straw biorefinery.

Application of hindered ether solvents for palladium catalyzed Suzuki-Miyaura, Sonogashira and cascade Sonogashira cross-coupling reactions.

Cross-coupling and cascade reactions typically rely on unsustainable and toxic volatile organic solvents. 2,2,5,5-Tetramethyloxolane (TMO) and 2,5-diethyl-2,5-dimethyloxolane (DEDMO) are both inherently non-peroxide forming ethers, and have been used in this work as effective, more sustainable, and potentially bio-based alternative solvents for Suzuki-Miyaura and Sonogashira reactions. Suzuki-Miyaura reactions demonstrated good yields for a range of substrates, 71-89% in TMO and 63-92% in DEDMO. In addition, a Sonogashira reaction exhibited the excellent yields of 85-99% performed in TMO, which was significantly higher than traditional volatile organic solvents, THF or toluene, and higher than those reported for another non-peroxide forming ether, namely eucalyptol. Cascade Sonogashira reactions utilizing a simple annulation methodology were particularly effective in TMO. Furthermore, a green metric assessment confirmed that the methodology employing TMO was more sustainable and greener than the traditional solvents THF and toluene, thereby demonstrating the promise of TMO as an alternative solvent for Pd-catalyzed cross-coupling reactions.

Sustainable solvents for ß-diketone extraction from wheat straw wax and their molecular self-assembly into nano-structured tubules for hydrophobic coatings.

Nonpolar, nonperoxide forming, sustainable and potentially bio-based solvents, namely 2,2,5,5-tetramethyloxolane (TMO) and 2,5-diethyl-2,5-dimethyloxolane (DEDMO), were utilized as an alternative to toxic petroleum-based hydrocarbon solvents for extraction of hentriacontane-14,16-dione from waste wheat straw waxes. This work is the first to report the application of DEDMO as a solvent for the extraction of natural products. The sustainable methodology developed in this research provided considerable advantages over previously reported systems in terms of high extraction yields, excellent selectivity towards the ß-diketones and low amounts of waste generated. DEDMO provided the highest recovery yield for all the sustainable solvents investigated, recovering 23.7% of the wax (which is a 68.8% yield of the ß-diketone). The extracted lipophilic hentriacontane-14,16-dione was utilised in combination with the sustainable solvents TMO or DEDMO to facilitate the creation of highly hydrophobic coatings. Moreover, the use of DEDMO was found to aid in the self-assembly of nano-structured tubule formation of both the unrefined wax and isolated ß-diketone. Green metric evaluation using process mass intensity (PMI), E-factor, solvent intensity (SI), and water intensity (WI) demonstrated that the described extraction procedure for hentriacontane-14,16-dione was highly sustainable and safer than the previous methodology. This sustainable manufacturing process may create the potential to valorise agricultural wastes as part of a holistic biorefinery.

Acid-catalysed reactions of amines with dimethyl carbonate.

Highly effective acid-catalysed reactions of amines with dimethyl carbonate (DMC) have been conducted with significant yields and selectivity of carboxymethylation or methylation products. Lewis acids (FeCl3, ZnCl2, and AlCl3·6H2O), Brønsted acids (PTSA, acetic, and formic acids), and acids supported on silica (silica sulfuric and silica perchlorate) resulted in carboxymethylation of primary aliphatic amines with high conversions. It was found that the Lewis acid FeCl3 also promoted carboxymethylation of primary aromatic amines and secondary amines. At both 90 °C or an elevated temperature of 150 °C under pressure, AlCl3·6H2O demonstrated highly selective monomethylation of aromatic amines. In addition, both silica sulfuric acid and silica perchlorate at 90 °C exhibited no conversion for secondary amines but enhanced carboxymethylation with high conversions of 80.7-87.5% and selectivity of >99.00% at 150 °C in a pressure reactor. At 1.0 equivalent, both promoted excellent conversion and selectivity of primary aliphatic amines at 90 °C. In addition, they were easily recovered and reused for at least four additional reactions without significant loss of efficiency with consistent conversions and selectivity. Green metrics evaluation for the silica sulfuric acid-catalysed reaction highlighted the sustainability features of the process. Silica-supported catalysts are highly stable, making them ideal alternative catalysts for the methylation and carbonylation of various amines with DMC. Acid-catalysed DMC reactions of amines may expand the substrate scope and offer new opportunities for developing sustainable organic synthetic methodologies.

Effect of harvest time on the compositional changes in essential oils, cannabinoids, and waxes of hemp (Cannabis sativa L.).

Demand for cannabinoid is growing, with the global market expected to reach $9.69 billion by 2025. Understanding how chemical composition changes in hemp at different harvest times is crucial to maximizing this industrial crop value. Important compositional changes in three different compound classes (essential oils, cannabinoids, and lipids) from inflorescences (tops), leaves, and stems of hemp (Cannabis sativa L., Finola variety) at different harvesting stages have been investigated. Over 85% of the total extracts from the tops were cannabinoids, while leaves demonstrated the greatest quantities of wax ester and sterols. Essential oil and cannabinoid increased in tops until full flowering (third harvest), reaching 2030 µg g-1 and 39 475 µg g-1, respectively. Cannabinoids decreased at seed maturity (final harvest) to 26 969 µg g-1. This demonstrates the importance of early harvesting to maximize cannabidiol (CBD), which is highly sought after for its therapeutic and pharmacological properties. A total of 21 161 µg g-1 of CBD was extracted from the tops at full flowering (third harvest); however, a significant increase (63%) in the banned psychoactive tetrahydrocannabinol (THC) was observed from budding (157 µg g-1 of biomass) to the full flowering (9873 µg g-1 of biomass). Harvesting the tops after budding is preferable due to the high CBD content and low amounts of THC.

Characterization of dissolved organic carbon and disinfection by-products in biochar filter leachate using orbitrap mass spectrometry.

Biochar is a low-cost adsorbent with considerable potential for utilization as a water filtration medium; however, organic matter leaching from biochar can lead to the formation of disinfection by-products (DBPs). This study investigated the leaching of dissolved organic carbon (DOC) from eucalyptus-derived biochar and the formation of DBPs generated by chlorination and chloramination. Column experiments with empty bed contact times (EBCTs) of 10 and 30 min were conducted for 200 bed volumes (BVs). The highest DOC concentration (3.5 µg-C/g-biochar) was detected with an EBCT of 30 min. Chloroform (49 µg/L) and dichloroacetonitrile (7 µg/L) because of chlorination were found during the first five BVs, but were reduced thereafter. During the first 10 BVs, unknown chlorinated DBPs generated (CHOCl) by chlorination and chloramination (193 and 152 formulae, respectively) were tentatively identified via an unknown screening analysis. The release of DBP precursors from biochar tentatively identified in this study will impact water filtration applications.

Activated carbons from waste Cassia bakeriana seed pods as high-performance adsorbents for toxic anionic dye and ciprofloxacin antibiotic remediation.

Waste Cassia bakeriana seed pods were used for porous carbon production in a facile pyrolysis process. The carbons were highly efficient adsorbents for methylene blue, congo red and ciprofloxacin antibiotic from aqueous media. The experimental results demonstrated that despite moderate surface area of 283.4 m2/g, KOH activated carbon (PSAC-KOH) exhibited the highest adsorption capacity for congo red reported to date for carbon-based adsorbents (970 mg/g). PSAC-KOH also demonstrated a high adsorption capacity at 600 mg/g for ciprofloxacin. Raman spectroscopy, X-ray diffraction and X-ray Photoelectron spectroscopy analysis of the carbons demonstrated an extensive graphitic characteristic, while Fourier transform infrared spectra of PSAC-KOH suggested a high proportion of aromaticity which promotes adsorption mechanisms including electrostatic and π-π interactions. Pseudo-second-order kinetic model fitting suggested a rate-controlling chemisorption mechanism. The utilization of waste Cassia bakeriana seed pods for carbon production may create new opportunities to develop sustainable and highly efficient adsorbents for water remediation.

High pressure systems as sustainable extraction and pre-treatment technologies for a holistic corn stover biorefinery.

This mini-review assesses supercritical carbon dioxide (scCO2) extraction and high-pressure carbon dioxide pre-treatment technologies for valorisation of corn stover agricultural residues with particular focus on showing how these can aid in the creation of a holistic biorefineries. Corn stover is currently the largest source of agriculture residues in the USA, as such there is significant potential for exploitation to yield valuable chemicals. ScCO2 extraction could lead to the recovery of a variety of different chemicals which include flavonoids, sterols, steroid ketones, hydrocarbons, saturated fatty acids, unsaturated fatty acids, fatty alcohols, phenolics and triterpenoids. Importantly, recent studies have not only demonstrated that supercritical extraction can be utilized for the recovery of plant lipids for use in consumer products, including nutraceuticals and personal care, but the processing of treated biomass can lead to enhanced yields and recovery of other products from biorefinery processes. Despite the great potential and opportunities for using scCO2 and high-pressure systems in a biorefinery context their real-world application faces significant challenges to overcome before it is widely applied. Such challenges have also been discussed in the context of this mini-review.

Graphitic mesoporous carbon-silica composites from low-value sugarcane by-products for the removal of toxic dyes from wastewaters.

Highly porous carbon-silica composites (CSC) were prepared for the first time through a simple wet impregnation process and subsequent pyrolysis of low-value sugarcane by-products, namely molasses. These CSC materials demonstrate a distinct range of functionalities, which significantly differ from similar materials published in the literature. Importantly, the carbon-silica composites prepared at 800°C exhibited exceptional adsorption capacities for the azo-dye congo red (445 mg g-1), due to the graphitic carbon coating and unique functionality including C-O-C within the porous structure. Congo red adsorption capacity of the highly mesoporous graphitic carbon-silica composites significantly exceeds that of commercial activated carbon and silica, these carbon-silica composites therefore represent an effective step towards the development of porous bio-derived adsorbent for remediation of dye wastewaters. Both the porous properties (surface area and pore size distribution) and the functionality of the carbon coating were dependent on the temperature of preparation. The sustainable synthetic methods employed led to a versatile material that inherited the mesoporosity characteristics from the parent silica, demonstrating mesoporous volumes greater than 90% (as calculated from the total pore volume). Adsorption on the 800°C prepared carbon-silica composites demonstrated an excellent fit with the Langmuir isotherm and the pseudo-first-order kinetic model.

Simultaneous manganese adsorption and biotransformation by Streptomyces violarus strain SBP1 cell-immobilized biochar.

Consumption of water containing high proportions of manganese could cause Parkinson's like symptoms and damage the central nervous systems. This study aims to investigate the potential of manganese removal through the development of microbial cell-immobilized biochar. The wood vinegar industry generates a large volume of carbonized wood waste (natural biochar) from the pyrolytic process. This is the first investigation utilizing this low value waste combined with biological treatment for water purification. Raw and hydrogen peroxide-modified biochars were used to immobilize an effective manganese-oxidizing bacterium, Streptomyces violarus strain SBP1 (SBP1). The results demonstrated that the modified biochar had a higher proportion of oxygen-containing functional groups leading to better manganese removal. Manganese adsorption by the modified biochar fitted pseudo-second-order and Langmuir models with the maximum adsorption capacity of 1.15 mg g-1. The modified biochar with SBP1 provided the highest removal efficiency at 78%. The advanced synchrotron analyses demonstrated that manganese removal by the biochar with SBP1 is due to the synergistic combination of manganese adsorption by biochars and biological oxidation by SBP1.

Synthesis and application of tuneable carbon-silica composites from the microwave pyrolysis of waste paper for selective recovery of gold from acidic solutions.

Microwave pyrolysis bio-oil from waste paper and K60 silica gel has successfully been utilised to synthesise mesoporous carbon-silica composites with uniquely tuneable surface properties, where functionality and structural characteristics can be altered and even enhanced by curing at different temperatures. This temperature-dependence resulted in composites ranging from highly oxygenated polymerised bio-oil composites at 300 °C to aromatic carbonaceous materials covering the silica surface at 800 °C, making them attractive materials for gold recovery from mining wastewater. The composite materials exhibit exceptional ability and selectivity to recover gold from dilute solutions. Metal adsorption on the surface of these composites proceeded via both chemisorption and physisorption leading to the reduction of Au(iii) to Au(0), resulting in high recovery capacities for gold. Composite material prepared at 500 °C demonstrated the optimum combination of surface functionality and porosity, allowing for an adsorption capacity of 320 mg g-1 of gold and with 99.5% removal being achieved at concentrations mimicking those of real-life mine tailing wastes. All materials pioneered in this research display great potential as selective adsorbents for the recovery of gold from acidic media.

Preparation of activated carbon from Dipterocarpus alatus fruit and its application for methylene blue adsorption.

Activated carbons were prepared from three parts of Dipterocarpus alatus fruit (wing, endocarp and pericarp), an abundant and renewable waste in Southeast Asia, by chemical activation using ZnCl2, FeCl3, H3PO4 and KOH and physical activation using CO2 and steam. This study indicated that activated carbon prepared from Dipterocarpus alatus fruit could be employed as a promising adsorbent for the removal of methylene blue from aqueous solution. ZnCl2 activation led to an activated carbon with a surface area of 843 m2 g-1 and was able to remove methylene blue from aqueous solution. Adsorption studies were performed and analysed using Langmuir and Freundlich isotherm equations. Adsorption data demonstrated an excellent fit with the Langmuir isotherm model, with the maximum adsorption capacity of 269.3 mg g-1 at equilibrium. Pseudo-first order and pseudo-second order kinetic models were used in this study to describe the adsorption mechanism. The results show that methylene blue adsorption is pseudo-second order, indicating that liquid film diffusion, intra-particle diffusion and surface adsorption coexisted during methylene blue adsorption on the activated carbon. The activated carbon prepared from Dipterocarpus alatus fruit is a low cost and effective adsorbent with a fast rate for the removal of methylene blue from aqueous solutions when compared with a number of activated carbons studied in the literature.

Conservation of Critical Elements of the Periodic Table.

Since its conception, the periodic table and the elements contained within it have shaped our modern lives. The use of many elements is now ubiquitous and essential for the modern technologies we have now become accustomed to. However, our use of some elements may be considered as unsustainable and their current use may create both economic and environmental pressures. The United Nations have designated 2019 the "International Year of the Periodic Table". As such this Essay presents some important points on "critical elements" and the importance of adopting sustainable practices in the use of all elements of the periodic table. This article also highlights a number of examples of green technologies for elemental recovery and some of the challenges we must overcome to become truly sustainable across the whole periodic table.

Lignin materials for adsorption: Current trend, perspectives and opportunities.

Lignin is a highly aromatic low value biomass residue, which can be utilized for chemicals, fuels and materials production. In recent years significant attention has focused on adsorbent materials from lignin. However, only 5% of available lignin is exploited worldwide, thus significant opportunities still exist for materials development. This review summarizes recent research advances in lignin-based adsorbents, with a particular emphasis on lignin, its modification and carbon materials derived from this abundant feedstock. Lignin derived activated carbons have been utilized for air pollutant adsorption (e.g. CO2, SO2 and H2S), while modified lignin materials have been developed for the removal of organic dyes and organics (like methylene blue, Procion Blue MX-R and phenols), heavy metals (such as Cu, Zn, Pb and Cd), or recovery of noble metals (e.g., Pd, Au and Pt). Future perspectives highlight how green chemistry approaches for developing lignin adsorbents can generate added value processes.

Development of hyperbranched crosslinkers from bio-derived platform molecules for the synthesis of epoxidised soybean oil based thermosets.

Bio-based carboxyl-terminated hyperbranched crosslinkers have been synthesised by the facile esterification reaction of glycerol with succinic anhydride (Gly-SA). The Gly-SA crosslinking molecules have a large number of terminal carboxyl groups, which can crosslink through the epoxide of epoxidised soybean oil (ESO), making a highly flexible transparent film with excellent oxidative resistance. The effect of different molecular weights of Gly-SA cured ESO on the thermal and mechanical properties of the resulting films was also investigated. This study demonstrated that an increase in the molecular weights of Gly-SA, led to a decrease in the curing rate of mixtures, whilst the glass transition temperature (T g) of Gly-SA cured ESO increased due to the incorporation of the bulky crosslinker. The use of a Gly-SA crosslinker prepared at 150 °C, resulted in a film (EGS150) with a tensile strength 13 times greater than of the control film, exhibited more than a 220% increase in elongation at break and the Young's modulus quadrupled compared to the value obtained for the control sample. It is noteworthy that the tensile strength and elongation at break improved with increasing Gly-SA chain length, suggesting the pre-polymerised crosslinkers contribute to the enhanced mechanical properties of the materials.