Augmented reality system based on the integration of polarization-independent metalens and micro-LEDs.

Augmented reality (AR), a technology that superimposes virtual information onto a user's direct view of real-world scenes, is considered one of the next-generation display technologies and has been attracting considerable attention. Here, we propose a flat optic AR system that synergistically integrates a polarization-independent metalens with micro light-emitting diodes (LEDs). A key component is a meticulously designed metalens with a numerical aperture of 0.25, providing a simulated focusing efficiency of approximately 76.5% at a wavelength of 532 nm. Furthermore, the laser measurement system substantiates that the fabricated metalens achieves a focusing efficiency of 70.8%. By exploiting the reversibility of light characteristics, the metalens transforms the divergent light from green micro-LEDs into a collimated beam that passes through the pupil and images on the retina. Monochromatic pixels with a size of 5×5 µm2 and a pitch of 10 µm can be distinctly resolved with a power efficiency of 50%. This work illustrates the feasibility of integrating the metalens with microdisplays, realizing a high-efficiency AR device without the need for additional optical components and showcasing great potential for the development of near-eye display applications.

[Application prospect of reaction engineering approach in studying drying behavior of single droplet during spray drying of traditional Chinese medicine].

Spray drying technology is one of the most commonly used unit operations in the production of traditional Chinese medicine(TCM) preparations, offering advantages such as short drying time and uniform product quality. However, due to the properties of TCM extracts, such as high viscosity, strong hygroscopicity, and poor flowability, there is limited scope to solve the problems of wall adhesion and clumping in spray drying from the macroscopic perspective of pharmaceutical production. Therefore, it has become a trend to study and optimize the spray drying process from the microscopic point of view by investigating single droplet evaporation behavior. Based on the reaction engineering approach(REA), the single droplet drying system, as a novel method for studying droplets, collects parameter data on individual TCM droplets during the drying process and uses the REA to process the data and establish predictive models. This approach is crucial for understanding the mechanism of TCM spray drying. This paper summarized and analyzed the cha-racteristics of various single droplet systems, the application of REA in single droplet drying systems, and its significance in optimizing the process, predicting drying states, and shortening the development cycle in the field of TCM spray drying, and looked ahead to the prospects of this method, including the introduction of new parameters and imaging techniques, aiming to provide a reference for further research in the field of TCM spray drying.

Technological process optimization and measurement of image quality of the electrically bifocal metalens.

This Letter describes the design procedure and process optimization of the electrically bifocal metalens. In our design, horizontal and vertical polarization is manipulated by applying a suitable voltage to a twisted nematic liquid crystal (TN-LC) cell. Each nanostructure is designed to be a rectangular prism, making different polarizations of light experience various phase delays, thus causing bi-focus. We selected lithographical methods to fabricate our metalens because of the minimum physical size, which can be as small as 50 nm, and the maximum aspect ratio, which is as high as 15. Furthermore, to increase the tolerance and make the sidewall vertical and smooth, we coated different characteristics of photoresist sensitivity to the upper and lower layers. After the development, the mushroom-type photoresist makes Ni easier to strip while in the lift-off process, thus increasing the quality of the whole metalens. Our experiment shows that the focal lengths and focusing efficiencies corresponding to the two polarizations are similar to the simulation results. The proposed electrically modulated bifocal metalens can be utilized in different applications and combined with other optical components.

[Current research status and application prospect of numerical simulation in traditional Chinese medicine drying].

With the rapid development of computer technology, numerical simulation has gradually become an important method to study drying process and improve drying equipment. Using computer to simulate the drying process of traditional Chinese medicine(TCM) is characterized by intuitiveness, scientificity, and low cost, which serves as an auxiliary means for technical innovation in TCM drying. This paper summarizes the theories of different drying methods and the research status of numerical simulation in drying, introduces the modeling methods and software of numerical simulation, and expounds the significance of numerical simulation modeling in shortening the research and development cycle, improving drying equipment, and optimizing drying parameters. However, the current numerical simulation method for drying process has problems, such as low accuracy, lack of quantitative indicators for the control of simulation results on the process, and insufficient in-depth research on the mechanism of drug quality changes. Furthermore, this paper put forward the application prospect of numerical simulation in TCM drying, providing reference for the further study of numerical simulation in this field.