Antireflection microstructures on ZnSe for mid- and far-IR fabricated by femtosecond laser ablation assisted with wet chemical etching.

Most infrared materials used in high-power systems, such as optical parametric generators, have high values of refractive indices, which result in high Fresnel losses. The performance of conventional antireflection coatings is limited when used in high-power and ultra-broadband systems. An alternative approach is to fabricate antireflection microstructures (ARMs) that allow for a broadband increase in transmittance without reducing the damage threshold of the material. In this work, ARMs were fabricated on the surface of ZnSe crystals using the femtosecond laser ablation assisted with wet chemical etching method. This allowed to produce high aspect ratio microstructures that increase the transmittance up to 98% in the mid- and far- infrared regions.

High-sensitivity and high-speed measurements of ultrashort pulses as short as 74 fs at 1.9 µm using a GRENOUILLE device.

Ultrashort laser pulse sources in the wavelength range of 1.8 to 2 µm have many potential applications including medicine, materials processing, and sensing. In the use of such lasers, a crucial task is to measure their pulse's temporal intensity and phase. Such measurement devices are most useful when they are simple to build and operate and also have high speed and high sensitivity. The GRENOUILLE measurement device with few components, no moving parts, sensitivity of hundreds of picojoules, and measurement speed of hundreds of milliseconds, is commonly used to solve this problem at other wavelengths. In this paper, the measurement of ultrashort pulses by a GRENOUILLE device, developed using a silicon matrix sensor, for pulses in the wavelength range of 1.8 to 2 µm has been demonstrated. It is shown that ultrashort pulses with durations of 74 to 900 fs and a maximum spectral FWHM of 85 nm can be measured with this device. The recently developed ultra-reliable RANA approach was used for pulse retrieval from the measured traces. The device's performance was validated by comparing its measurements with those obtained by the robust FROG technique.

Laser induced damage threshold of GaSe with antireflection microstructures at a wavelength of 5 µm.

Large GaSe crystals were grown and various antireflection microstructures (ARMs) were fabricated on their cleaved surfaces using optimized femtosecond laser ablation, which provided the antireflection effect in a wide wavelength range of 4-16 µm. The influence of ARMs created on the GaSe surface on the change of the laser-induced damage threshold (LIDT) of the crystal at a wavelength of 5 µm was evaluated. The 5-µm Fe:ZnMgSe laser with the pulse duration of 135 ns was used for the LIDT test in conditions close to single pulse exposure. The measured values of LIDT of 56 ± 6 MW/cm2 and 51 ± 9 MW/cm2 for two GaSe substrates, respectively, were comparable with the known data of single pulse LIDT of GaSe. The average LIDT intensities of 54 ± 6 MW/cm2 and 52 ± 7 MW/cm2 for the ARMs at two GaSe plates, respectively, were close to LIDT intensities for the corresponding GaSe substrates. The ARMs with lower structural quality had lower LIDT (50-52 MW/cm2) in comparison with the high-quality ARMs (58-60 MW/cm2). High LIDT for high-quality ARMs can be caused by increased selenium content in the ARMs. In any case, all the tested ARMs on the GaSe plates with different surface quality are workable for development of widely tunable mid-infrared nonlinear optical converters.

Diffuse reflectance spectroscopy of the cartilage tissue in the fourth optical window.

Studies of the optical properties of biological tissues in the infrared range have demonstrated significant potential for diagnostic tasks. One of the insufficiently explored ranges for diagnostic problems at the moment is the fourth transparency window, or short wavelength infrared region II (SWIR II). A Cr2+:ZnSe laser with tuning capability in the range from 2.1 to 2.4 µm was developed to explore the possibilities in this region. The capability of diffuse reflectance spectroscopy to analyze water and collagen content in biosamples was investigated using the optical gelatin phantoms and the cartilage tissue samples during their drying process. It was demonstrated that decomposition components of the optical density spectra correlated with the partial content of the collagen and water in the samples. The present study indicates the possibility of using this spectral range for the development of diagnostic methods, in particular, for observation of the changes in the content of cartilage tissue components in degenerative diseases such as osteoarthritis.

Antireflection microstructures fabricated on the surface of a LiGaSe2 nonlinear crystal.

LiGaSe2 is a propitious material for nonlinear parametric conversion in the mid-infrared (mid-IR) range. Its refractive index of n = 2.25 in the 2-12 µm wavelength range results in significant losses due to Fresnel reflection. However, the conventional method of increasing the transmittance with antireflection coatings (ARCs) significantly reduces the damage threshold of the material. Fabrication of the antireflection microstructures (ARMs) is an alternative approach for increasing the surface transmittance. In this work, ARMs were fabricated on the surface of a LiGaSe2 crystal using a single-pulse femtosecond laser ablation method. An average transmittance of 97.2% in the 2-8 µm spectral range and the maximum transmittance of 98.6% at 4.1 µm were achieved.

All-fiber ultrafast amplifier at 1.9 µm based on thulium-doped normal dispersion fiber and LMA fiber compressor.

The duration reduction and the peak power increase of ultrashort pulses generated by all-fiber sources at a wavelength of [Formula: see text] are urgent tasks. Finding an effective and easy way to improve these characteristics of ultrafast lasers can allow a broad implementation of wideband coherent supercontinuum sources in the mid-IR range required for various applications. As an alternative approach to sub-100 fs pulse generation, we present an ultrafast all-fiber amplifier based on a normal-dispersion germanosilicate thulium-doped active fiber and a large-mode-area silica-fiber compressor. The output pulses have the following characteristics: the central wavelength of [Formula: see text], the repetition rate of 23.8 MHz, the energy per pulse period of 25 nJ, the average power of 600 mW, and a random output polarization. The pulse intensity and phase profiles were measured via the second-harmonic-generation frequency-resolved optical gating technique for a linearly polarized pulse. The linearly polarized pulse has a duration of 71 fs and a peak power of 128.7 kW. The maximum estimated peak power for all polarizations is 220 kW. The dynamics of ultrashort-pulse propagation in the amplifier were analyzed using numerical simulations.

Speed characterization of p-i-n photodiode based on GaSb/GaInAsSb/GaAlAsSb heterostructure with frontal bridge contact at 1.9 µm.

We report a study of the response function parameters (amplitude and rise/fall time) of a high-speed GaSb/GaInAsSb/GaAlAsSb photodiode operating at 1.9 µm as a function of optical input power and reverse bias voltage. The experimental measurement results yield the optimal pulse energy and optimal reverse bias voltage for the photodiode. The 44 ps minimal rise time of the response function and 3.6 GHz bandwidth are achieved under a 3 V reverse bias voltage and pulse energy in the 0.27-2.5 pJ range.

Fabrication of antireflection microstructures on the surface of GaSe crystal by single-pulse femtosecond laser ablation.

GaSe crystals are promising as nonlinear optical converters in the mid- and far-IR ranges. However, it is challenging to increase the GaSe surface transmittance of 77% with conventional antireflection coatings because of poor surface quality, leading to coating adhesion problems. Antireflection microstructures (ARMs) offer an alternative way of increasing surface transmittance. In this work, ARMs were fabricated on the surface of a GaSe plate by single-pulse femtosecond laser ablation. An average GaSe surface transmittance of 94% in the 7-11 µm range and a maximum transmittance of 97.8% at 8.5 µm were obtained. The proposed method can be used to increase the efficiency of GaSe-based nonlinear converters.

Numerical model of hybrid mode-locked Tm-doped all-fibre laser.

Ultrafast Tm-doped fibre lasers have been actively studied for the last decade due to their potential applications in precise mid-IR spectroscopy, LIDARs, material processing and more. The majority of research papers is devoted to the comparison between a numerical modelling and experimental results; however, little attention is being paid to the comprehensive description of the mathematical models and parameters of the active and passive components forming cavities of Tm-doped all-fibre lasers. Thus, here we report a numerical model of a stretched-pulsed Tm-doped fibre laser with hybrid mode-locking and compare it with experimental results. The key feature of the developed numerical model is employment of the experimentally measured dispersion coefficients and optimisation of some model parameters, such as the bandwidth of the spectral filter spectral filtering and the saturation power of the active fibre, for a conformity with the experiment. The developed laser emits 331.7 fs pulses with a 23.8 MHz repetition rate, 6 mW of average power, 0.25 nJ of pulse energy, and a 21.66 nm spectral bandwidth at a peak wavelength of 1899.5 nm. The numerical model characteristics coincide with experimentally achieved spectral width, pulse duration, and average power with inaccuracy of 4.7%, 5.4%, and 22.9%, respectively. Moreover, in the discussion of the work the main possible reasons influencing this inaccuracy are highlighted. Elimination of those factors might allow to increase accuracy even more. We show that numerical model has a good agreement with the experiment and can be used for development of ultrafast Tm-doped fibre laser systems.

Generation of multi-solitons and noise-like pulses in a high-powered thulium-doped all-fiber ring oscillator.

We report a study on the switching of the generation regimes in a high-powered thulium-doped all-fiber ring oscillator that is passively mode-locked with nonlinear polarization evolution technique with different pumping rates and cavity dispersion values. In one experimental setup, switching was observed between the noise-like pulse and the multi-soliton (in the forms of soliton bunches and soliton rain) regimes by the adjustment of the intracavity polarization controllers. We attributed this to the crucial influence of the nonlinear polarization evolution strength determined by such key parameters as saturation (over-rotation) power, linear phase bias, and nonlinear losses on the pulse evolution and stability. So the soliton collapse effect (leading to noise-like pulse generation) or the peak power clamping effect (generating a bunch of loosely-bound solitons) may determine pulse dynamics. Both the spectrum bandwidth and coherence time were studied for noise-like pulses by varying the cavity length and pump power, as well as the duration of solitons composing bunches. As a result, both noise-like pulses (with spectrum as broad as 32 nm bandwidth) and multi-soliton formations (with individual pulse-widths ranging from 748 to 1273 fs with a cavity length increase from 12 to 53 m) with up to 730 mW average power were generated at a wavelength of around 1.9 µm. The results are important for the realization of the broadband and smooth supercontinuum which can be used as a source for mid-IR vibrational spectroscopy of gas samples for breath analysis and environmental sensing.

High-efficiency continuous-wave single-mode room-temperature operation of Cr:CdSe single-crystal laser with output power of 2.3 W.

We report on the study of quenching and thermal lensing based on simple effective lens approximation in a Cr2+:CdSe active medium, including detailed research on the medium's luminescence lifetime dependence on temperature in the 236-391 K range. This work has allowed us to partially overcome the limitations associated with thermal effects in the medium and build a laser system that allowed power scalability to be realized for the Cr2+:CdSe laser. Longitudinal pumping using a continuous-wave Tm-doped fiber laser at 1.908 µm produced an output of 2.3 W at 2.65 µm with an absorbed pump power slope efficiency of 47.6%, which, to the best of our knowledge, is the highest output power achieved in Cr:CdSe continuous-wave lasers.

Stable Similariton Generation in an All-Fiber Hybrid Mode-Locked Ring Laser for Frequency Metrology.

Ultrashort pulse lasers constitute an important tool in the emerging field of optical frequency metrology and are enabling unprecedented measurement capabilities and new applications in a wide range of fields, including precision spectroscopy, atomic clocks, ultracold gases, and molecular fingerprinting. We demonstrate the generation of stable 127-fs self-similar pulses at a central wavelength of 1560 nm with 7.14-mW average output power. Similariton lasers have a low repetition rate deviation in the averaging time interval [Formula: see text], a low relative intensity noise [Formula: see text] (30 Hz to 10 kHz), a narrow single comb line width of 32 kHz, and high reliability. Thus, such lasers are highly promising for further development of the stabilized combs and open up a robust and substantially simplified route to synthesizing low-noise microwaves.