Comparative Evaluation of Effectiveness of Calcium Hydroxide, MTA, and TheraCal LC in Indirect Pulp Capping in Primary Molars: In Vivo Study.

AIM: This investigation aimed to observe the effects of Dycal, mineral trioxide aggregate (MTA), and TheraCal LC, as indirect pulp-capping materials in primary molars. MATERIALS AND METHODS: About 75 children with lower primary molars aged between 4 and 7 years suggested for IPC were selected and randomly allocated into: Group I - Dycal, group II - MTA, and group III - TheraCal LC. An immediate postoperative radiograph was taken after the procedure. Recall examination was done after 3 and 6 months for clinical and radiographic assessment. The radiographs were digitized, and the amount of thickness of dentin was assessed using Corel Draw software. The values were tabulated and subjected to paired t-tests and independent t-tests for intra and intergroup analysis, respectively. The p-value < 0.05 was considered statistically significant. RESULTS: There was a statistically significant increase in dentin thickness in the first 3 months compared to the 6-month follow-up. At the end of the research phase, TheraCal LC had more tertiary dentin deposited than MTA, followed by Dycal. CONCLUSION: TheraCal LC can be a reliable indirect pulp-capping agent in primary teeth. CLINICAL SIGNIFICANCE: Indirect pulp capping (IPC) is a very extensively employed treatment regimen to manage extensive caries. For many decades, calcium hydroxide has been regarded as the benchmark of pulp capping materials. With several advancements in materials for restoration, TheraCal LC a resin-modified, light-cured calcium silicate-filled liner serves as a pulp-capping agent and dentin protector, promoting pulp healing and preserving vitality as an obstacle cum protector of the dental pulp complex. How to cite this article: Thomas NA, Jobe J, Thimmaiah C, et al. Comparative Evaluation of Effectiveness of Calcium Hydroxide, MTA, and TheraCal LC in Indirect Pulp Capping in Primary Molars: In Vivo Study. J Contemp Dent Pract 2024;25(4):365-371.

Effect of Bonding Agents on the Shear Bond Strength of Tooth-colored Restorative Materials to Dentin: An In Vitro Study.

AIM: The aim of the study is to determine the difference in the shear bond strengths to dentin among dental composite (Filtek Z350®, 3M), compomer (Dyract Flow®, Dentsply) and Giomer (Beautifil®, Shofu) with 3MTM Single BondTM Universal Adhesive (SBU) (7th generation, self-etch, single solution adhesive) and AdperTM Single Bond 2 Adhesive (ASB) (5th generation, total-etch, two solution adhesive). MATERIALS AND METHODS: Sixty extracted human permanent teeth were collected, cleansed of debris, and placed in distilled water. The samples were segregated into two groups depicting the two bonding agents-AdperTM (ASB) and 3MTM Single Bond Universal (SBU) and sub-grouped into three groups depicting the three restorative materials (Composite, Giomer, and Compomer) used. Groups were respresented as follows: Group I-ASB + Composite; Group II-ASB + Giomer; Group III-ASB + Compomer; Group IV-SBU + Giomer; Group V-SBU + Compomer; Group VI-SBU + Composite. After applying the bonding agent as per the manufacturer's instructions, following which the restorative material was placed. A Universal Testing Machine (Instron 3366, UK) was employed to estimate the shear bond strength of the individual restorative material and shear bond strengths were calculated. RESULTS: Composite bonded with SBU (group VI) displayed the greatest shear strength (11.16 ± 4.22 MPa). Moreover, Giomers and flowable compomers displayed better bond strengths with ASB compared with their SBU-bonded counterparts. CONCLUSION: These results mark the importance of careful material selection in clinical practice and the bonding agent used to achieve optimal bond strength and enhance the clinical longevity and durability of dental restorations. CLINICAL SIGNIFICANCE: From a clinical perspective, to avoid a compressive or a shear failure, it would be preferrable to use a direct composite restorative material with SBU (Single bond universal adhesive, 7th generation) to achieve maximum bond strength. How to cite this article: Kuchibhotla N, Sathyamoorthy H, Balakrishnan S, et al. Effect of Bonding Agents on the Shear Bond Strength of Tooth-colored Restorative Materials to Dentin: An In Vitro Study. J Contemp Dent Pract 2024;25(3):245-249.