The effect of moisture content over the fibre saturation points on the impact strength of wood.

The article's main aim is to assess the mechanical behaviour of linden under high-rate loadings (impact) and its change due to changes in moisture content (MC) over fibre saturation point. For assessing the mechanical properties of green wood, mainly the data of the dried wood is not applicable since the moisture content can drastically affect the mechanical properties of the wood. By testing both dried and high-moisture-content wood, we can understand a general viewpoint toward the effect of the moisture content on the impact behaviour of the wood. Several test samples were made of linden wood with different moisture content levels of 11%, 60% and 160%. A drop-weight impact machine tested the specimens to measure the reaction force of the hammer during a very short impact period. The results of the tests were parameters such as force-time chart, the maximum force required for crack initiation, the impact bending strength (IBS) and the work needed for crack initiation. The results indicated an increase in MC decreases the maximum force, work required for crack initiation and IBS drastically. However, when MC exceeded the fibre saturation point (FSP), there was no further influence on the force pattern and maximum required force.

Fomes fomentarius and F. inzengae-A Comparison of Their Decay Patterns on Beech Wood.

Wood-decaying fungi are responsible for the degradation of wood and the alteration in its material properties. Fomes fomentarius (L.) Fr. is one of the most common white-rot fungi colonising coarse wood and standing trees. In recent years, according to their genetic, physiological, and morphological differences, Fomes inzengae (Ces. and De Not.) Lécuru was identified as an independent species. This article aimed to compare the impact of the degradation caused by both species on the anatomical, physical, and mechanical properties of beech wood. When comparing the degradation caused by different strains of both species, no statistically significant difference was found in mass loss (ML) or moisture content (MC). A relevant correlation between ML and MC was confirmed for both species. Variabilities in the density distribution of the degraded and intact bending samples were found to be statistically different. No relevant difference was observed in the modulus of rupture (MOR) between the two species after each exposure period. A strong linear relationship between the MOR and the dynamic modulus of elasticity was revealed for both species. Both species showed decay patterns typical for simultaneous white rot and soft rot. According to the presented results, the impact of both species on the investigated material properties of wood cannot be considered significantly different.

Effects of Wood Particles from Deadwood on the Properties and Formaldehyde Emission of Particleboards.

The volume of deadwood increases annually because of changes in environmental, climatic, and hydrological conditions. On the other hand, during the last decade, manufacturers of wood-based boards have been facing an acute problem of a shortage of conventional raw materials. The purpose of this study was to evaluate the possibility of using wood particles from deadwood in the production of particleboards. Three-layer particleboards with different content of deadwood particles (0%, 25%, 50%, 75%, 100%) were produced. Conventional urea-formaldehyde (UF) resin was used for gluing the particles. The physical and mechanical properties of the boards, as well as the formaldehyde content in the boards, were determined. In addition, the effect of adding melamine-urea-formaldehyde (MUF) resin to UF adhesive on the properties of the boards was investigated. Replacing conventional sound wood particles with deadwood particles leads to deterioration of the physical and mechanical properties of the boards. The boards from deadwood particles absorb more water and swell more. The bending strength (MOR), modulus of elasticity in bending (MOE), and internal bonding (IB) values for boards with 100% deadwood particles are reduced by 26.5%, 23.1%, and 72.4%, respectively, compared to reference boards from sound wood particles. Despite this, a significant advantage is that boards made from 100% deadwood particles are characterized by 34.5% less formaldehyde content than reference boards made from conventional sound wood. Moreover, adding 3% of MUF resin to UF adhesive increases MOR, MOE, and IB by 44.1%, 43.3%, and 294.4%, respectively.

Physical-Mechanical Properties of Peat Moss (Sphagnum) Insulation Panels with Bio-Based Adhesives.

Rising energy and raw material prices, dwindling resources, increased recycling, and the need for sustainable management have led to growth in the smart materials sector. In recent years, the importance and diversity of bio-based adhesives for industrial applications has grown steadily. This article focuses on the production and characterization of insulation panels consisting of peat moss and two bio-based adhesives. The panels were pressed with tannin and animal-based resins and compared to panels bonded with urea formaldehyde. The physical-mechanical properties, namely, thermal conductivity (TC), water vapor diffusion resistance, modulus of rupture (MOR), modulus of elasticity (MOE), internal bond (IB), compression resistance (CR), water absorption (WA) and thickness swelling (TS) were measured and analyzed. The results show that the insulation effectiveness and mechanical stability of moss panels bound with tannin and animal glue are comparable to standard adhesives used in the composite industry.

Surface Characteristics of One-Sided Charred Beech Wood.

The aim of this paper was to analyze selected properties of beech wood (Fagus sylvatica L.) treated by one-sided surface charring. Specimens were one-side charred with a hot plate using several time-temperature combinations (from 200 to 400 °C). Characteristics such as colour, discoloration, surface roughness, fire resistance, total carbohydrate content at several wood layers and decay resistance were evaluated. Surface charring was applied to the radial and tangential surfaces. Colour measurements showed that the surface of the wood turned grey due to charring. In addition to colour measurements, other experiments showed significant differences between radial and tangential specimens due to their different structures. The higher the temperature used in treating them, the lower the roughness values for radial specimens, while the trend for tangential specimens was the opposite. A smoother surface is more fire resistant, so radial specimens are generally better in this regard. Tangential specimens are more susceptible during preparation to forming cracks that impair flame resistance because a continuous protective densified layer is not formed. The determination of total carbohydrates revealed significant changes at various wood depths after surface charring. These changes were more predictable in radial specimens due to the annual ring orientation, because each layer consisted of a similar earlywood/latewood ratio. Finally, when decay resistance was assessed, weight loss was found to be lower in all specimens than in the references. The results suggest that charring at a particular combination of temperature and time improved the investigated properties of the surface-modified beech.