Composites of Titanium-Molybdenum Mixed Oxides and Non-Traditional Carbon Materials: Innovative Supports for Platinum Electrocatalysts for Polymer Electrolyte Membrane Fuel Cells.

TiO2-based mixed oxide-carbon composite support for Pt electrocatalysts provides higher stability and CO tolerance under the working conditions of polymer electrolyte membrane fuel cells compared to traditional carbon supports. Non-traditional carbon materials like graphene nanoplatelets and graphite oxide used as the carbonaceous component of the composite can contribute to its affordability and/or functionality. Ti(1-x)MoxO2-C composites involving these carbon materials were prepared through a sol-gel route; the effect of the extension of the procedure through a solvothermal treatment step was assessed. Both supports and supported Pt catalysts were characterized by physicochemical methods. Electrochemical behavior of the catalysts in terms of stability, activity, and CO tolerance was studied. Solvothermal treatment decreased the fracture of graphite oxide plates and enhanced the formation of a reduced graphene oxide-like structure, resulting in an electrically more conductive and more stable catalyst. In parallel, solvothermal treatment enhanced the growth of mixed oxide crystallites, decreasing the chance of formation of Pt-oxide-carbon triple junctions, resulting in somewhat less CO tolerance. The electrocatalyst containing graphene nanoplatelets, along with good stability, has the highest activity in oxygen reduction reaction compared to the other composite-supported catalysts.

Promising Fluorine-Free Ion Exchange Membranes Based on a Poly(ether-block-amide) Copolymer and Sulfonated Montmorillonite: Influence of Different Copolymer Segment Ratios.

Novel composite membranes employing a poly(ether-block-amide) (PEBAX) copolymer and sulfonated montmorillonite (S-MMT) as a filler were developed. The ratio of polyether to polyamide blocks was investigated using PEBAX 2533 and PEBAX 4533 based on the membrane properties and performance. Additionally, the effect of the changing filler ratio was monitored. The interaction between the S-MMT as nanofiller and the polymer matrix of PEBAX2533 and PEBAX4533 as well as the crystalline nature and thermal and mechanical stability of the composite membranes were evaluated using Fourier Transform Infrared Spectroscopy (FT-IR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), and tensile test. The composite membrane with 7 wt.% S-MMT showed the highest water uptake of 21% and 16% and an acceptable swelling degree of 16% and 9% for PEBAX 2533 and PEBAX 4533 composite membranes, respectively. In terms of water uptake and ion exchange capacity at room temperature, the new un-protonated membranes are superior to un-protonated Nafion. Meanwhile, with the same S-MMT content, the ion conductivity of PEBAX 2533 and PEBAX 4533 composite membranes is 2 and 1.6 mS/cm, and their ion exchange capacity is 0.9 and 1.10 meq/g.

Reductive Treatment of Pt Supported on Ti0.8Sn0.2O2-C Composite: A Route for Modulating the Sn-Pt Interactions.

The composites of transition metal-doped titania and carbon have emerged as promising supports for Pt electrocatalysts in PEM fuel cells. In these multifunctional supports, the oxide component stabilizes the Pt particles, while the dopant provides a co-catalytic function. Among other elements, Sn is a valuable additive. Stong metal-support interaction (SMSI), i.e., the migration of a partially reduced oxide species from the support to the surface of Pt during reductive treatment is a general feature of TiO2-supported Pt catalysts. In order to explore the influence of SMSI on the stability and performance of Pt/Ti0.8Sn0.2O2-C catalysts, the structural and catalytic properties of the as prepared samples measured using XRD, TEM, XPS and electrochemical investigations were compared to those obtained from catalysts reduced in hydrogen at elevated temperatures. According to the observations, the uniform oxide coverage of the carbon backbone facilitated the formation of Pt-oxide-C triple junctions at a high density. The electrocatalytic behavior of the as prepared catalysts was determined by the atomic closeness of Sn to Pt, while even a low temperature reductive treatment resulted in Sn-Pt alloying. The segregation of tin oxide on the surface of the alloy particles, a characteristic material transport process in Sn-Pt alloys after oxygen exposure, contributed to a better stability of the reduced catalysts.

Insights into the Influence of Different Pre-Treatments on Physicochemical Properties of Nafion XL Membrane and Fuel Cell Performance.

Perfluorosulfonic acid (PFSA) polymers such as Nafion are the most frequently used Proton Exchange Membrane (PEM) in PEM fuel cells. Nafion XL is one of the most recently developed membranes designed to enhance performance by employing a mechanically reinforced layer in the architecture and a chemical stabilizer. The influence of the water and acid pre-treatment process on the physicochemical properties of Nafion XL membrane and Membrane Electrode Assembly (MEA) was investigated. The obtained results indicate that the pre-treated membranes have higher water uptake and dimensional swelling ratios, i.e., higher hydrophilicity, while the untreated membrane demonstrated a higher ionic exchange capacity. Furthermore, the conductivity of the acid pre-treated Nafion XL membrane was ~ 9.7% higher compared to the untreated membrane. Additionally, the maximum power densities obtained at 80 °C using acid pre-treatment were ~ 0.8 and 0.93 W/cm2 for re-cast Nafion and Nafion XL, respectively. However, the maximum generated powers for untreated membranes at the same condition were 0.36 and 0.66 W/cm2 for re-cast Nafion and Nafion XL, respectively. The overall results indicated that the PEM's pre-treatment process is essential to enhance performance.

Development of WO3-Nafion Based Membranes for Enabling Higher Water Retention at Low Humidity and Enhancing PEMFC Performance at Intermediate Temperature Operation.

The proton exchange membrane (PEM) represents a pivotal material and a key challenge in developing fuel cell science and hydrogen technology. Nafion is the most promising polymer which will lead to its commercialisation. Hybrid membranes of nanosized tungsten oxide (WO3) and Nafion were fabricated, characterised, and tested in a single cell. The incorporation of 10 wt% WO3 resulted in 21% higher water uptake, 11.7% lower swelling ratio, almost doubling the hydration degree, and 13% higher mechanical stability of the hybrid membrane compared to the Nafion XL. Compared to commercial Nafion XL, the rNF-WO-10 hybrid membrane showed an 8.8% and 20% increase in current density of the cell at 0.4 V operating at 80 and 95 °C with 1.89 and 2.29 A/cm2, respectively. The maximum power density has increased by 9% (0.76 W/cm2) and 19.9% (0.922 W/cm2) when operating at the same temperatures compared to the commercial Nafion XL membrane. Generally, considering the particular structure of Nafion XL, our Nafion-based membrane with 10 wt% WO3 (rNF-WO-10) is a suitable PEM with a comparable performance at different operating conditions.

Electrocatalytic Properties of Mixed-Oxide-Containing Composite-Supported Platinum for Polymer Electrolyte Membrane (PEM) Fuel Cells.

TiO2-based mixed oxide-carbon composite supports have been suggested to provide enhanced stability for platinum (Pt) electrocatalysts in polymer electrolyte membrane (PEM) fuel cells. The addition of molybdenum (Mo) to the mixed oxide is known to increase the CO tolerance of the electrocatalyst. In this work Pt catalysts, supported on Ti1-xMoxO2-C composites with a 25/75 oxide/carbon mass ratio and prepared from different carbon materials (C: Vulcan XC-72, unmodified and functionalized Black Pearls 2000), were compared in the hydrogen oxidation reaction (HOR) and in the oxygen reduction reaction (ORR) with a commercial Pt/C reference catalyst in order to assess the influence of the support on the electrocatalytic behavior. Our aim was to perform electrochemical studies in preparation for fuel cell tests. The ORR kinetic parameters from the Koutecky-Levich plot suggested a four-electron transfer per oxygen molecule, resulting in H2O. The similarity between the Tafel slopes suggested the same reaction mechanism for electrocatalysts supported by these composites. The HOR activity of the composite-supported electrocatalysts was independent of the type of carbonaceous material. A noticeable difference in the stability of the catalysts appeared only after 5000 polarization cycles; the Black Pearl-containing sample showed the highest stability.

Effect of the Microstructure of the Semiconductor Support on the Photocatalytic Performance of the Pt-PtOx/TiO2 Catalyst System.

The influence of the semiconductor microstructure on the photocatalytic behavior of Pt-PtOx/TiO2 catalysts was studied by comparing the methanol-reforming performance of systems based on commercial P25 or TiO2 from sol-gel synthesis calcined at different temperatures. The Pt co-catalyst was deposited by incipient wetness and formed either by calcination or high-temperature H2 treatment. Structural features of the photocatalysts were established by X-ray powder diffraction (XRD), electron spin resonance (ESR), X-ray photoelectron spectroscopy (XPS), optical absorption, Raman spectroscopy and TEM measurements. In situ reduction of Pt during the photocatalytic reaction was generally observed. The P25-based samples showed the best H2 production, while the activity of all sol-gel-based samples was similar in spite of the varying microstructures resulting from the different preparation conditions. Accordingly, the sol-gel-based TiO2 has a fundamental structural feature interfering with its photocatalytic performance, which could not be improved by annealing in the 400-500 °C range even by scarifying specific surface area at higher temperatures.

Study of PtOx/TiO2 Photocatalysts in the Photocatalytic Reforming of Glycerol: The Role of Co-Catalyst Formation.

In this study, relationships between preparation conditions, structure, and activity of Pt-containing TiO2 photocatalysts in photoinduced reforming of glycerol for H2 production were explored. Commercial Aerolyst® TiO2 (P25) and homemade TiO2 prepared by precipitation-aging method were used as semiconductors. Pt co-catalysts were prepared by incipient wetness impregnation from aqueous solution of Pt(NH3)4(NO3)2 and activated by calcination, high temperature hydrogen, or nitrogen treatments. The chemico-physical and structural properties were evaluated by XRD, ¹H MAS NMR, ESR, XPS, TG-MS and TEM. The highest H2 evolution rate was observed over P25 based samples and the H2 treatment resulted in more active samples than the other co-catalyst formation methods. In all calcined samples, reduction of Pt occurred during the photocatalytic reaction. Platinum was more easily reducible in all of the P25 supported samples compared to those obtained from the more water-retentive homemade TiO2. This result was related to the negative effect of the adsorbed water content of the homemade TiO2 on Pt reduction and on particle growth during co-catalyst formation.

Synergism between constituents of multicomponent catalysts designed for ethanol steam reforming using partial least squares regression and artificial neural networks.

Effects of different catalyst components on the catalytic performance in steam reforming of ethanol have been investigated by means of Artificial Neural Networks (ANNs) and Partial Least Square regression (PLSR). The data base consisted of ca. 400 items (catalysts with varied composition), which were obtained from a former catalyst optimization procedure. Marten's uncertainty (jackknife) test showed that simultaneous addition of Ni and Co has crucial effect on the hydrogen production. The catalyst containing both Ni and Co provided remarkable hydrogen production at 450°C. The addition of Ceas modifier to the bimetallic NiCo catalyst has high importance at lower temperatures: the hydrogen concentration is doubled at 350°C. Addition of Pt had only little effect on the product distribution. The outliers in the data set have been investigated by means of Hotelling T2 control chart. Compositions containing high amount of Cu or Ce have been identified as outliers, which points to the nonlinear effect of Cu and Ce on the catalytic performance. ANNs were used for analysis of the non-linear effects: an optimum was found with increasing amount of Cu and Ce in the catalyst composition. Hydrogen production can be improved by Ce only in the absence of Zn. Additionally, negative cross-effect was evidenced between Ni and Cu. The above relationships have been visualized in Holographic Maps, too. Although predictive ability of PLSR is somewhat worse than that of ANN, PLSR provided indirect evidence that ANNs were trained adequately.

Assessment of predictive ability of artificial neural networks using holographic mapping.

In this study, artificial neural networks (ANNs) were used to reveal a quantitative relationship between catalytic composition and catalytic activity. This relationship was predefined using a hypothetical experimental space described by a multidimensional polynomial. The predictive ability of ANNs was investigated, i.e. an attempt was done to evaluate how ANNs can envisage a given hypothetical experimental space. Data sets for training, validation and testing of ANNs were obtained from the hypothetical experimental space using two different ways of sampling. Data were selected, (i) by means of our optimization algorithm called Holographic Research Strategy (HRS); and (ii) randomly. In order to model real experimentation, data were also generated with error. The relationship between the complexity of different network topologies and their predictive ability was investigated. It was shown that when data used for training have been perturbed with a given level of noise, less complex network architectures give acceptable accuracy. Additionally, estimated experimental spaces were visualized in a 2D layout by means of Holographic Mappings (HMs). Analysis of HMs revealed that ANNs trained by data sets obtained upon an optimization procedure provides better description of the experimental space in the vicinity of the optimum than ANNs trained by randomly selected data sets. This fact indicates again the importance of the optimization in combinatorial catalyst library design.

Characterization of trimetallic Pt-Pd-Au/CeO2 catalysts combinatorial designed for methane total oxidation.

In the present work, the role and the effect of platinum and gold on the catalytic performance of ceria supported tri-metallic Pt-Pd-Au catalysts have been studied. The optimum composition of these tri-metallic supported catalysts has been discovered using methods and tools of combinatorial catalyst library design. Detailed catalytic, spectroscopic and physico-chemical characterization of catalysts in the vicinity of the optimum in the given compositional space has been performed. The temperature-programmed oxidation of methane revealed that the addition of Pt and Au to Pd/CeO2 catalyst resulted in higher conversion values in the whole investigated temperature range compared to the monometallic Pd catalyst. The time-on-stream experiments provided further evidence for the high-stability of tri-metallic catalysts compared to the monometallic one. Kinetic studies revealed the stronger adsorption of methane on Pt-Pd/CeO2 catalysts than over Pd/CeO2. XPS analysis showed that Pt and Au stabilize Pd in a more reduced form even under condition of methane oxidation. FTIR spectroscopy of adsorbed CO and hydrogen TPD measurements provided indirect evidences for alloying of Pt and Au with Pd. CO chemisorption data indicated that tri-metallic catalysts have increased accessible metallic surface area. It is suggested that advantageous catalytic properties of tri-metallic Pt-Au-Pd/CeO2 catalysts compared to the monometallic one can be attributed to (i) suppression of the formation of ionic forms of Pd(II), (ii) reaching an optimum ratio between Pd0 and PdO species, and (iii) stabilization of Pd in high dispersion. The results also indicate that Pd0 - PdO ensemble sites are required for methane activation.