Heat is an inexhaustible source of energy, and it can be exploited by thermoelectronics to produce electrical power or electrical responses. The search for a low-cost thermoelectric material that could achieve high efficiencies and can also be straightforwardly scalable has turned significant attention to the halide perovskite family. Here, we report the thermal voltage response of bismuth-based perovskite derivates and suggest a path to increase the electrical conductivity by applying chalcogenide doping. The films were produced by drop-casting or spin coating, and sulfur was introduced in the precursor solution using bismuth triethylxanthate. The physical-chemical analysis confirms the substitution. The sulfur introduction caused resistivity reduction by 2 orders of magnitude, and the thermal voltage exceeded 40 mV K-1 near 300 K in doped and undoped bismuth-based perovskite derivates. X-ray diffraction, Raman spectroscopy, and grazing-incidence wide-angle X-ray scattering were employed to confirm the structure. X-ray photoelectron spectroscopy, elemental analysis, scanning electron microscopy, and energy-dispersive X-ray spectroscopy were employed to study the composition and morphology of the produced thin films. UV-visible absorbance, photoluminescence, inverse photoemission, and ultraviolet photoelectron spectroscopies have been used to investigate the energy band gap.
The increasing energy demand and the ever more pressing need for clean technologies of energy conversion pose one of the most urgent and complicated issues of our age. Thermoelectricity, namely the direct conversion of waste heat into electricity, is a promising technique based on a long-standing physical phenomenon, which still has not fully developed its potential, mainly due to the low efficiency of the process. In order to improve the thermoelectric performance, a huge effort is being made by physicists, materials scientists and engineers, with the primary aims of better understanding the fundamental issues ruling the improvement of the thermoelectric figure of merit, and finally building the most efficient thermoelectric devices. In this Roadmap an overview is given about the most recent experimental and computational results obtained within the Italian research community on the optimization of composition and morphology of some thermoelectric materials, as well as on the design of thermoelectric and hybrid thermoelectric/photovoltaic devices.
Pure sulfide kesterite (Cu2ZnSnS4) is one of the most promising emerging photovoltaic technologies thanks to its excellent absorption coefficient, cost-effectiveness, and environmental sustainability. However, record efficiencies are not exceeding 11% due to several issues, such as absorber defects or a nonoptimal band alignment with the toxic but conventionally used CdS buffer layer. To get rid of it, several efforts have been made in the past few years. Among recent theoretical works, TiO2 has been suggested as a suitable buffer layer due to its optical and electrical properties, giving extremely promising results in device simulation. However, there are few experimental examples combining TiO2 with kesterite, and they generally show very modest performances. In this Letter, we report on the preliminary and promising results of our experimental procedure for the production of Cd-free kesterite photovoltaic devices featuring ALD-TiO2 as a buffer layer, leading to efficiencies comparable with our CZTS/CdS reference devices.
In the last few decades, the attention of scientific community has been driven toward the research on renewable energies. In particular, the photovoltaic (PV) thin-film technology has been widely explored to provide suitable candidates as top cells for tandem architectures, with the purpose of enhancing current PV efficiencies. One of the most studied absorbers, made of earth-abundant elements, is kesterite Cu2ZnSnS4 (CZTS), showing a high absorption coefficient and a band gap around 1.4-1.5 eV. In particular, thanks to the ease of band-gap tuning by partial/total substitution of one or more of its elements, the high-band-gap kesterite derivatives have drawn a lot of attention aiming to find the perfect partner as a top absorber to couple with silicon in tandem solar cells (especially in a four-terminal architecture). In this work, we report the effects of the substitution of tin with different amounts of germanium in CZTS-based solar cells produced with an extremely simple sol-gel process, demonstrating how it is possible to fine-tune the band gap of the absorber and change its chemical-physical properties in this way. The precursor solution was directly drop-cast onto the substrate and spread with the aid of a film applicator, followed by a few minutes of gelation and annealing in an inert atmosphere. The desired crystalline phase was obtained without the aid of external sulfur sources as the precursor solution contained thiourea as well as metal acetates responsible for the in situ coordination and thus the correct networking of the metal centers. The addition of KCl in dopant amounts to the precursor solution allowed the formation of well-grown compact grains and enhanced the material quality. The materials obtained with the optimized procedure were characterized in depth through different techniques, and they showed very good properties in terms of purity, compactness, and grain size. Moreover, solar-cell prototypes were produced and measured, exhibiting poor charge extraction due to heavy back-contact sulfurization as studied in depth and experimentally demonstrated through Kelvin probe force microscopy.
Lead halide perovskites have been revolutionary in the last decade in many optoelectronic sectors. Their bismuth-based counterparts have been considered a good alternative thanks to their composition of earth-abundant elements, good chemical stability, and low toxicity. Moreover, their electronic structure is in a quasi-zero-dimensional (0D) configuration, and they have recently been explored for use beyond optoelectronics. A significant limitation in applying thin-film technology is represented by the difficulty of synthesizing compact layers with easily scalable methods. Here, the engineering of a two-step synthesis in an air of methylammonium bismuth iodide compact thin films is reported. The critical steps of the process have been highlighted so that the procedure can be adapted to different substrates and application areas.
Achieving thermoelectric devices with high performance based on low-cost and nontoxic materials is extremely challenging. Moreover, as we move toward an Internet-of-Things society, a miniaturized local power source such as a thermoelectric generator (TEG) is desired to power increasing numbers of wireless sensors. Therefore, in this work, an all-oxide p-n junction TEG composed of low-cost, abundant, and nontoxic materials, such as n-type ZnO and p-type SnOx thin films, deposited on borosilicate glass substrate is proposed. A type II heterojunction between SnOx and ZnO films was predicted by density functional theory (DFT) calculations and confirmed experimentally by X-ray photoelectron spectroscopy (XPS). Moreover, scanning transmission electron microscopy (STEM) combined with energy-dispersive X-ray spectroscopy (EDS) show a sharp interface between the SnOx and ZnO layers, confirming the high quality of the p-n junction even after annealing at 523 K. ZnO and SnOx thin films exhibit Seebeck coefficients (α) of â¼121 and â¼258 µV/K, respectively, at 298 K, resulting in power factors (PF) of 180 µW/m K2 (for ZnO) and 37 µW/m K2 (for SnOx). Moreover, the thermal conductivities of ZnO and SnOx films are 8.7 and 1.24 W/m K, respectively, at 298 K, with no significant changes until 575 K. The four pairs all-oxide TEG generated a maximum power output (Pout) of 1.8 nW (≈126 µW/cm2) at a temperature difference of 160 K. The output voltage (Vout) and output current (Iout) at the maximum power output of the TEG are 124 mV and 0.0146 µA, respectively. This work paves the way for achieving a high-performance TEG device based on oxide thin films.
Dye-Sensitized Photoelectrochemical Cells (DS-PECs) have been emerging as promising devices for efficient solar-induced water splitting. In DS-PECs, dyes and catalysts for water oxidation and/or reduction are typically two separate components, thus limiting charge transfer efficiency. A small number of organometallic dyes have been integrated with a catalyst to form an integrated dye-catalyst dyad for photoanodes, but until now no dyads based on metal-free organic dyes have been reported for photoanodes. We herein report the first example of dyad-sensitized photoanodes in DS-PEC water splitting based on metal-free organic dyes and a Ru catalyst. The di-branched donor-π-acceptor dyes carry a donor carbazole moiety which has been functionalized with two different terminal pyridyl ligands in order to coordinate a benchmark Ru complex as a water oxidation catalyst, affording water oxidation dyads. The two dyads have been fully characterized in their optical and electrochemical properties, and XPS has been used to confirm the presence of the catalyst bonded to the dye anchored to the semiconductor anode. The two dyads have been investigated in DS-PEC, showing an excellent faradaic efficiency (88% average across all cells, with a best cell efficiency of 95%), thus triggering new perspectives for the design of efficient molecular dyads based on metal-free dyes for DS-PEC water splitting.
Photovoltaics is a promising technology to produce sustainable energy, thanks to the high amount of energy emitted by the sun. One way of having solar cells with low production costs is to apply thin-film technology and with earth-abundant raw materials. A keen interest is arising in kesterite compounds, which are chalcogenides composed of abundant and non-toxic elements. They have already achieved excellent performance at the laboratory level. Here, we report the synthesis and characterization of mixed chalcogenides based on copper, zinc, iron, and tin. Solutions have been studied with different zinc and iron ratios. The distortion of the elementary cell of kesterite increases with the addition of iron until a phase transition to stannite occurs. The process of synthesis and deposition proposed herein is cheap and straightforward, based on the sol-gel technique. These thin films are particularly attractive for use in cheap and easily processable solar cells. The synthesized layers have been characterized by X-ray diffraction, UV-Vis absorption, and Raman, X-ray photoelectron, and energy-dispersive X-ray spectroscopy measurements.
In this work, the data on the effect of peripheral functionalization of a series of triphenylamine based di-branched dyes used as sensitizers in dye-sensitized solar cells are presented. The effect of different alkyl functionalities on the donor moiety upon the optical and photovoltaics parameters have been investigated in dye-sensitized solar cells (DSSCs) using a 10-µm TiO2 active layer. The absorption spectra, output efficiency, and incident photon to conversion efficiency of the DSSCs have been collected. The data can be exploited for properly designing efficient, stable, and industrially viable dyes for third generation solar devices.
At the end of 2017 roughly 1.8% of the worldwide electricity came from solar photovoltaics (PV), which is foreseen to have a key role in all major future energy scenarios with an installed capacity around 5 TW by 2050. Despite silicon solar cells currently rule the PV market, the extremely more versatile thin film-based devices (mainly Cu(In,Ga)Se2 and CdTe ones) have almost matched them in performance and present room for improvement. The low availability of some elements in the present commercially available PV technologies and the recent strong fall of silicon module price below 1 $/Wp focused the attention of the scientific community on cheap earth-abundant materials. In this framework, thin film solar cells based on Cu2ZnSnS4 (CZTS) and the related sulfur selenium alloy Cu2ZnSn(S,Se)4 (CZTSSe) were strongly investigated in the last 10 years. More recently, chalcogenide PV absorbers potentially able to face TW range applications better than CZTS and CZTSSe due to the higher abundance of their constituting elements are getting considerable attention. They are based on both MY2 (where M = Fe, Cu, Sn and Y = S and/or Se) and Cu2XSnY4 (where X = Fe, Mn, Ni, Ba, Co, Cd and Y = S and/or Se) chalcogenides. In this work, an extensive review of emerging earth-abundant thin film solar cells based on both MY2 and Cu2XSnY4 species is given, along with some considerations on the abundance and annual production of their constituting elements.
The covalent functionalization of (7,6)-enriched single-walled carbon nanotubes (SWCNTs) with oligophenylenevinylene (OPV) moieties terminating with a dimethylamino group is proposed as an efficient way to enhance the affinity of CNTs with spiro-MeOTAD in perovskite-based solar cells. The evidence of SWCNTs functionalization and the degree of OPV substitution on SWCNTs are established from TGA, XPS, TEM, and Raman techniques. Our tailored doping materials afford photovoltaic performances in line with conventional Li-doped spiro-MeOTAD, showing at the same time a significantly improved chemical stability of the perovskite component over time. Furthermore, the comparison of the photovoltaic performances with those obtained with nonfunctionalized SWCNTs suggest that the presence of the organic appends ensures highly reproducible PV performances. These results demonstrate the suitability of this functionalized SWCNT material as a valid doping agent for spiro-MeOTAD, representing a viable alternative to the conventional Li salt.
A spectroscopic investigation focusing on the charge generation and transport in inverted p-type perovskite-based mesoscopic (Ms) solar cells is provided in this report. Nanocrystalline nickel oxide and PCBM are employed respectively as hole transporting scaffold and hole blocking layer to sandwich a perovskite light harvester. An efficient hole transfer process from perovskite to nickel oxide is assessed, through time-resolved photoluminescence and photoinduced absorption analyses, for both the employed absorbing species, namely MAPbI3-xClx and MAPbI3. A striking relevant difference between p-type and n-type perovskite-based solar cells emerges from the study.
Time-resolved photophysical and photoelectrochemical investigations have been carried out to compare the electron transfer dynamics of a 2-ß-substituted tetraarylporphyrinic dye (ZnB) and a 5,15-meso-disubstituted diarylporphyrinic one (ZnM) at the electrolyte/dye/TiO2 interface in PSSCs. Although the meso push-pull structural arrangement has shown, up to now, to have the best performing architecture for solar cell applications, we have obtained superior energy conversion efficiencies for ZnB (6.1%) rather than for ZnM (3.9%), by using the I(-)/I3(-)-based electrolyte. To gain deeper insights about these unexpected results, we have investigated whether the intrinsic structural features of the two different porphyrinic dyes can play a key role on electron transfer processes occurring at the dye-sensitized TiO2 interface. We have found that charge injection yields into TiO2 are quite similar for both dyes and that the regeneration efficiencies by I(-), are also comparable and in the range of 75-85%. Moreover, besides injection quantum yields above 80%, identical dye loading, for both ZnB and ZnM, has been evidenced by spectrophotometric measurements on transparent thin TiO2 layers after the same adsorption period. Conversely, major differences have emerged by DC and AC (electrochemical impedance spectroscopy) photoelectrochemical investigations, pointing out a slower charge recombination rate when ZnB is adsorbed on TiO2. This may result from its more sterically hindered macrocyclic core which, besides guaranteeing a decrease of π-staking aggregation of the dye, promotes a superior shielding of the TiO2 surface against charge recombination involving oxidized species of the electrolyte.
A facile and fast approach, based on microwave-enhanced Sonogashira coupling, has been employed to obtain in good yields both mono- and, for the first time, disubstituted push-pull Zn(II) porphyrinates bearing a variety of ethynylphenyl moieties at the ß-pyrrolic position(s). Furthermore, a comparative experimental, electrochemical, and theoretical investigation has been carried out on these ß-mono- or disubstituted Zn(II) porphyrinates and meso-disubstituted push-pull Zn(II) porphyrinates. We have obtained evidence that, although the HOMO-LUMO energy gap of the meso-substituted push-pull dyes is lower, so that charge transfer along the push-pull system therein is easier, the ß-mono- or disubstituted push-pull porphyrinic dyes show comparable or better efficiencies when acting as sensitizers in DSSCs. This behavior is apparently not attributable to more intense B and Q bands, but rather to more facile charge injection. This is suggested by the DFT electron distribution in a model of a ß-monosubstituted porphyrinic dye interacting with a TiO2 surface and by the positive effect of the ß substitution on the incident photon-to-current conversion efficiency (IPCE) spectra, which show a significant intensity over a broad wavelength range (350-650â nm). In contrast, meso-substitution produces IPCE spectra with two less intense and well-separated peaks. The positive effect exerted by a cyanoacrylic acid group attached to the ethynylphenyl substituent has been analyzed by a photophysical and theoretical approach. This provided supporting evidence of a contribution from charge-transfer transitions to both the B and Q bands, thus producing, through conjugation, excited electrons close to the carboxylic anchoring group. Finally, the straightforward and effective synthetic procedures developed, as well as the efficiencies observed by photoelectrochemical measurements, make the described ß-monosubstituted Zn(II) porphyrinates extremely promising sensitizers for use in DSSCs.
The first examples of thiocyanate-free thiophene-substituted Ru(II) cyclometalated complexes, based on thiophene-derived 2-(2,4-difluorophenyl)pyridine ligands, are presented and investigated as photosensitizers in DSCs. Upon thiophene substitution the complexes presented enhanced optical properties compared to the reference dye with no thiophene substitution. DSCs based on the dithienyl-derived dye showed power conversion efficiencies up to 5.7%, more than twice that containing the complex without the thiophene substitution.
